Silica brick is a refractory product containing SiO2 as a main component. Its SiO2 content is generally not less than 93%. Silica brick is an acidic refractory material. It has strong resistance to acid slag and good resistance to oxides such as CaO, FeO and Fe2O3. However, it has poor resistance to alkaline slag erosion and is easily oxidized by Al2O3, K2O and Na2O. Destruction by the action of matter. The softening temperature of the silicon brick load is as high as 1640~1680�°C, and the long-term use volume is stable under high temperature. However, silica bricks have poor thermal shock resistance and high refractoriness. When using silica bricks, pay attention to two points: when the silica brick is at 200~300�°C and 573�°C, the volume suddenly expands due to the crystal transformation. Therefore, the temperature rise below 600 �°C in the oven should not be too fast, when it is cooled to below 600 �°C. Dramatic temperature changes should be avoided; as far as possible not in contact with the alkaline slag. Application Coke oven, Hot blast stoves, Crown or Superstructure of glass furnace.
SiO2: 95% for coke oven, blast furnace, glass furnace.
Silica bricks are the main species of silica-based refractories, where the mass fraction of sio2 is not less than 93%. Silica brick is a typical acid refractory bricks, the acid slag has a good resistance to al2o3, feo, fe2o3 and other oxides also has good resistance, but the resistance to alkaline slag is poor, easy to cao, k2o, na2o and other oxides and damage. Silicone brick softening temperature as high as l640-1680 â??, long-term use at high temperatures more stable. But the thermal resistance of silicon brick is poor, refractoriness is not high enough.
Fused silica brick has better thermal shock resistance, much lower thermal expansion, and can be used to do hot repair. Fused Silica Brick for Hot Repair of Coke Oven is similar to general silica brick, but it has better thermal shock resistance. The property of fused silica brick is similar to general silica brick, but it has better thermal shock resistance, much lower thermal expansion and it can stand suddenly change of temperature. It also can be heated in very short time after buildup and do not need to calculate thermal expansion. So we can directly use its cold size for masonry. Put on wooden pallets, tightened with iron stripes, covered with plastic bag, warped with film, shipped in pallet by container. Do corner protection and other measures to avoid products from breaking. And these packages should be under ISPM standard.
A brief introduction of silica brick Silica brick is a kind of acid refractory mainly made from tridymite, cristobalite and a small amount of residual quartz as well as glass phase. The raw material is natural silica sand whose SiO2 content should be more than 96%. The higher SiO2 content in silica sand, the higher temperature silica bricks resist. Silica bricks are used in the roof and superstructure of glass melting tanks as well as for hot repairs. Our silica brick advantages --Adopts high quality silica and advanced technology, our silica bricks enjoy the advantages of high purity, long service life, good thermal conductivity, high refractoriness under load, and good creep resistance. --In addition, it has accurate size tolerance, pure color and luster appearance. --Because of the good thermal shock resistance of silica brick, it is mainly used in the continuous operating furnace. --Supporting the use of other high quality refractories, our silica brick can extent the service life of float glass furnace to 8 years and double the service life of bottle glass furnace. Applications The silica brick can be widely used in coke oven, hot blast furnace, glass furnace and carbon furnace. In glass industry, it is mainly employed to build the doghouse crown, suspended wall of channel, top crown and inlet sealing. In detail, silica bricks plays the following role in different fields: --being the partition walls in coke oven carbonization and burning chamber; --metallurgy industry: used as refractories for steel making open hearth regenerator, slag pocket, soaking pit; --arch crown and other weight bearing areas in ceramic kilns, hot blast furnace and acid open hearth; --worked as building checker chamber, chute, combustion chamber, coking chamber and furnace arch in glass melting furnaces. Specifications 1.Higher SiO2 content of more than 96%, with true density of 2.34g/cm3, thus it has good performance in corrosion of acid slag. 2.Excellent resistance in high temperature. The melting temperature under load is 1620-1670â??. Durable, with no deformation under high temperature. 3.Good thermal shock resistance, High heat conductivity. 4.At 1450, there is 1.5-2.2% overall expansion which makes the joint-cutting dovetailed, thus silica bricks have good air tightness and strong structure.
Description Adopts high quality silica and advanced technology, our silica bricks enjoy the advantages of high purity, long service life, good thermal conductivity, high refractoriness under load, and good creep resistance. In addition, it has accurate size tolerance, pure color and luster appearance. Because of the bad thermal shock resistance of silica brick, it is mainly used in the continuous operating furnace. Supporting the use of other high quality refractories, our silica brick can extent the service life of float glass furnace to 8 years and double the service life of bottle glass furnace. It is widely used in coke oven, hot blast furnace, glass furnace and carbon furnace. Applications The silica brick can be widely used in coke oven, hot blast furnace, glass furnce and carbon furnace. In glass industry, it is mainly employed to build the doghouse crown, suspended wall of channel, top crown and inlet sealing. In metallurgy industry, it is adopted as the nozzle brick. The main applications Doghouse crown, suspended wall of channel, top crown and inlet sealing of glass furnace High temperature part of coke oven. Specifications High purity Long service life Accurate size tolerance Pure color Luster appearance Advantages Good thermal conductivity High refractoriness under load Good creep resistance High refractoriness
Features: 1. Good acid and slag resistance. 2. Good thermal conductivity. 3. High tridymite content. 4. Accurate dimension and good appearance. Application: Mainly used for coke oven of coking chamber and combustion chamber partition, steel open hearth of regenerative chamber and sediment chamber, soaking furnace, glass melting furnace, refractory silica brick materials and ceramic firing kiln and kiln of the vault and other supporting parts. Used in the construction of regenerative chamber, chute, combustion chamber, coking chamber, furnace roof etc. parts of the coke ovens. Also used in hot blast stove of high temperature bearing parts and the roof of acid open hearth furnace. Technical Index: Item Silica Brick for Coke Oven Sole, Walls Other Positions SiO2 % 94.5 94.5 A12O3 % 1.0 1.0 Fe2O3 % 1.0 1.0 CaO % 2.5 2.5 Apparent Porosity % 22 24 True Density g/cm3 2.32-2.33 2.32-2.34 Cold Crushing Strength MPa 40 35 Refractoriness Under Load (0.2MPa) 1650-1660 Residual Quartz % 0-1 Permanent Linear Change (1450 *2h) % 0-0.2 0-0.2 Thermal Expansion Rate 1000 % 1.28 1.30 Refractoriness 1710
Silica brick is a kind of acid refractory mainly made from tridymite, cristobalite and a small amount of residual quartz as well as glass phase. The raw refractory material is natural silica sand whose SiO2Â content should be more than 96%. The higher SiO2Â content in silica sand, the higher temperature silica bricks resist, its refractoriness under load is as high as 1640 ~ 1670. Glass kiln silica brick has high temperature and volume stability, no pollution to glass liquid, chemical corrosion resistance, small bulk density, and can reduce the weight of furnace body. It also has the ability of resistance to acidic and alkalic steam attack with high performance of flushing resistance. It is mainly used to build the doghouse crown, suspended wall of channel, top crown and inlet sealing, and also to be used to build the checker chamber, chute, combustion chamber, coking chamber and furnace arch in glass melting furnaces. Silica brick has good corrosion resistance to glass liquid. It is the preferred refractory for crown construction of glass melting furnaces, in terms of cost, strength and of defect potential.
Advantages: 1.High purity. 2.Good thermal conductivity. 3.High refractoriness under load and high tridymite content. 4.Low true densit Application: 1.Widely used in hot blast stoves. 2.Used in high temperature sections of the checker chamber in hot blast stoves. 3.Used as low-cost alternative to andalusite and mullite checker bricks in hot blast stoves. 4.High refractoriness, average thermal shock resistance makes it suitable in consistent temperature environment. Technical Index: Item Silica Brick for Hot Blast Stove Wall bricks ,Dome Bricks Checker Brick SiO2 % Y95 Y95 A12O3 % ¨¹1.0 ¨¹1.0 Fe2O3 % ¨¹1.0 ¨¹1.0 Apparent Porosity % ¨¹22 ¨¹24 True Density g/cm3 ¨¹2.33 ¨¹2.33 Cold Crushing Strength MPa Y40 Y35 Refractoriness Under Load (0.2MPa) æ Y1650 Y1650 Residual Quartz % 1.0 1.0 Creep Rate 0.2MPa (155050h) % 0.6 ¨¹0.6 Permanent Linear Change ( 1450*2h) % ¨¹0.2 ¨¹0.2 Thermal Expansion Coefficient(1000æ) % ¨¹1.26 ¨¹1.26 Fumigated wooden pallet, using paper or non-woven fabrics between layers separated,plastic shrink film protected outside,finaly using straps. The size of wooden pallet is 95x95cm,95x100cm or as your requirements.
Advantages: 1. Longer service life, accurate size tolerance, pure color, luster appearance. 2. Excellent thermal shock resistance. 3. Good structural strength at high temperature. 4. Zero thermal expansion rate 5. Without crack and peeling phenomena. Application: 1. It is widely used in hot repair project on coke oven. 2. Coke oven maintenance time shortens greatly. Ensure the quality of coke oven repair. Improve the production of coke oven. 3. CUNSE is not only providing the hot repair method of coke oven, but also contracting for coke oven maintenance. Technical Index: Item Zero Expansion Silica Brick SiO2 % 96 Fe2O3 % 0.7 Al2O3+TiO2+R2O % 0.7 Refractoriness 1710 Apparent Porosity % 22 Bulk Density g/cm3 1.8-1.85 True Density g/cm3 2.34 Cold Crushing Strength Mpa 35 0.2Mpa Refractoriness Under Load T0.6 1680 Permanent Linear Change % 1500 X2h 0 +0.2 Thermal Expansion Coefficient 1000 0.2 Thermal Shock Resistance(1000 Water- cooling, cycles) 25
Feature It is mainly made of top class silica, via shaping and burning under the high temperature, possesses high temperature resistant, high strength and low impurities, etc. â?º Advantage: 1) Good thermal insulaton effects 2) Good acid erosion resistance. 3) High softening point with temperature. 4) No shrink in burn repeatedly. Stable Capability, High Quality, Excellent Service, Competitive price is the most important advantage of our products. Application: The main applications are the low temperature parts such as blast furnaces and hot blast furnaces, waste incinerators and glass melting furnaces.
Silica mullite brick is a special high-alumina bauxite and silicon carbide as raw materials, made by a special sintering process, with a strong high wear resistance, thermal shock stability characteristics, in the course of the formation of protective layer, and other characteristics. Mainly used for cement rotary kiln transition zone, decomposition zone. Feature: High refractoriness under load Highâ temperature resistance Lowâ thermal conductivity Good insulatingâ property High flexibility Proper bulk density -
Silica Brick for Coke Oven KNKSKS JG-94 Physical and chemical properties, dimension and appearance, strictly conform to DIN norm Application Construction of Coke Battery Coke Plant, Newly Built or Hot Repair
With the breakthrough of the suspension preheating and pre-decomposition technology in the cement industry and the increasing size of the equipment, the heat load of the kiln is significantly increased, the rotation speed is accelerated, the alkali corrosion is severe, and the lining life and equipment operation cycle are shortened, thus the requirements for refractory materials. More demanding. Its performance advantages are mainly manifested in: 1. High refractoriness under load and excellent high temperature resistance; 2. High strength, abrasion resistance, and easy to peel off and erosion; 3. Low thermal conductivity and good heat insulation effect; 4. Strong flexibility and heat resistance Excellent seismic performance; 5, moderate density, reduce the cylinder load.
Silica brick is a kind of acid refractory mainly made from tridymite, cristobalite and a small amount of residual quartz as well as glass phase. The raw material is natural silica sand whose SiO2 content should be more than 96%. The higher SiO2 content in silica sand, the higher temperature silica bricks resist. Silica bricks are used in the roof and superstructure of glass melting tanks as well as for hot repairs.
Silica bricks are the main species of silica-based refractories, where the mass fraction of SiO2 is not less than 93%. Silica brick is a typical acid refractory bricks, the acid slag has a good resistance to Al2O3, FeO, Fe2O3 and other oxides also has good resistance, but the resistance to alkaline slag is poor, easy to CaO, K2O, Na2O and other oxides and damage. Features: 1.Good acid and erosion resistance, powerful anti high-temperature strength. 2.Soften melting temperature is 1620~1670 °C. 3.Low thermal shock resistance. 4.Natural silica as raw material, plus regular mineralizer. 5.Ensure good bonding and structural strength of furnace. 6.Good heat resistance and long service life. Application: 1.Glass melting furnace, ceramic frit kiln, sodium silicate furnace, soaking furnace, ceramic kiln, etc 2.Coke oven's coking chamber, combustion chamber walls, steel open-hearth's regenerator and sediment chamber, etc. 3.Load-bearing parts of high temperature hot air furnace and acid open-hearth furnace roof, etc. Items Fire Proof Thermal Insulating SiC+SiO2,% 30 - Al2O3,% 65 50 Bulk Density,g/cm3 2.65 - Apparent Porosity,% 19 25 Cold Compressive Strength,Mpa 90 40 Refractoriness UnderLoad, ºC 1650 1680 ThermalShock Resistance,cycles(1100 ºC,water cooling) 20 20 Thermal Conductivity,w/m.k(350 ºC) 2.5 1.4
Cunse silica brick for glass kiln has the characteristics of high purity, high density, high strength and high soft, high refractoriness. It also has the ability of resistance to acidic and alkalic steam attack with high performance of flushing resistance.
Products: Refractory bricks, unshaped refractory, refractory fibre, landscape brick, etc. Our refractory brick include: fireclay brick, high alumina brick, low porosity fireclay brick, mullite brick, silica brick, zircon brick, insulating brick, alkali resistant bricks, etc.
Advantages: â?¢CUNSE has its own crystalline silica mine in Tie men Town which is famous for its silica mine. â?¢High purity, good thermal conductivity, high refractoriness under load and high tridymite content, low true density, low expansion, low creep and low residual quartz content, good dimension and appearance. Areas of Application: â?¢Widely used in hot blast stoves. â?¢Used in high temperature sections of the checker chamber in hot blast stoves. â?¢Used as low-cost alternative to andalusite and mullite checker bricks in hot blast stoves. â?¢High refractoriness, average thermal shock resistance makes it suitable in consistent temperature environment. Physical and Chemical Properties: â?¢Mineralize â?¢Silica content exceeds 95% â?¢Refractoriness up to 1710â??
It is mainly made of top class silica, via shaping and burning under the high temperature, possesses high temperature resistant, high strength and low impurities, etc. Advantage: 1) Good thermal insulaton effects 2) Good acid erosion resistance. 3) High softening point with temperature. 4) No shrink in burn repeatedly. Stable Capability, High Quality, Excellent Service, Competitive price is the most important advantage of our products. Application: The main applications are the low temperature parts such as blast furnaces and hot blast furnaces, waste incinerators and glass melting furnaces. z
