Introduction: As the sump pump, series lm(r)s pumps are of single casing and made of wear-resistant metal and natural rubber. The wear parts are made of high chromium for series lms and are rubber lined for series lrs. According to liquid level of the slurry pool, the vertical slurry pump transmission shaft and suction pipe could be chosen for different length. This sump pump could operate under the best condition with different speeds. Application: The vertical slurry pumps are designed to transport the abrasive, large particle and high-density slurries and applied over the fields such as metallurgy, mining, chemistry, coal washery, power plant, building materials and environmental protection.
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
Pumps,Water pumps
700bar Hydraulic pump for hydraulic puncher.
En590, jet fuel a1, pet coke, pump, valve, cosmetic, mechanical seal, cotton bag, glass bottle, hand sanitizer, hydraulics, cosmetic bottles,socks, paper drink straw, alcohol wipe, other korean products, mask, or nitrile gloves and hand sanitizer and korean cosmetics.
Product Description The TS/TSR heavy duty cantilever sump pump is designed for applications requiring greater reliability and durability than conventional vertical process pump can offer. The heavy duty cantilever design makes the TS/TSR pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. · TS pump - hard metal construction · TSR pump - rubber covered construction Structure: Fully Cantilevered – Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. Impellers – Unique double suction impellers; fluid flow enters the top as well as the bottom. This design eliminates shaft seals and reduces thrust load on the bearings. Large Particle – Large particle impellers are also available and enable passing unusually large solids. Bearing Assembly – The maintenance friendly bearing assembly has heavy duty roller bearings, robust housings, and a massive shaft. Casing – The metal pumps have a heavy walled abrasive resistant 27% chrome alloy casing. Rubber pumps have a molded rubber casing adhered to sturdy metal structures. Column and Discharge Pipe – The metal pump columns and discharge pipes are steel, and the rubber columns and discharge pipes are rubber covered. Upper Strainers – Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. Lower Strainers – Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles. Specification 300T-TS Vertical Pump Capacity (Q) : 288-1267m³/h Head (H) : 6-33m Power (KW) : 200KW Speed(N) : 350-700r Effiency : 50 Impeller Dia.: 610mm Impeller No.: 5 Outlet Dia.: 300mm Weight: 3940kg Slurry Pump Spares Pumps spare and parts material : High chrome alloy:A33, A05, A07, A49, etc. vertical slurry pump Natural rubber: R08, R26, R33, R55, etc. Other material as per requests, like stainless steel, duplex stainless steel, Nickle alloy, Alloy 20, and so on. Applications Mining Coal washery Power plant Metallurgy Petrochemical Building material Dredging Other industrial departments, etc. This series of pumps are preferred by many customers with special installation requirements and widely applied in pool. Its wear-resistant metal liner could handle abrasive slurries with rough particles and high concentration.
Type vs and vsr pumps are vertical, centrifugal slurry pumps submerged in sump to work. They are designed for delivering abrasive, large particle and high density slurries. These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties. Wet parts of type vs pump are made of abrasion-resistant metal. All parts of type vsr pump immersed in liquid are lined with rubber outer liner. They are suited to transport non-edge angle abrasive slurry. The type with¡°l¡±is a sump pump of extension shaft series, which is suited for the working condition of deeper level. The guide bearing construction is added to the pump on the basis of the standard pump, so the pump is with both more steady operation and wider application range, but flushing water should be attached to the guide bearing.
We are one of the concrete pump manufacturers in Korea Brand: SAMIL GIANT in Korea Boom length: 67m 62m 58m 52m 48m 45m 42m 37m 32m 28m 24m 21m Stationary pump, Line pump We are able to send full details if you make an inquiry
Pumps
Agri. Vertical Vmc Openwell
300TV-SP Vertical Slurry Pump is designed to be immersed in liquid for conveying abrasive, coarse particles, dirty water and particle contaminated water. Due to the design of the pump assembly, a shaft seal is not required and the pump can be operated in conditions that most pumps would have a low service life and their seal arrangement would not be effective.
Tobee® vertical spindle slurry pump with electric motor Specification: Size (discharge): 40mm to 300mm Capacity: 7.2~ 1492 m3/hr Head: 5.5m ~ 47 m Handing solids: 0 ~ 65mm Concentration: 0%~ 70% Material:high chrome alloy, rubber, polyurethane, stainless steel etc.
double tube hand pump for BIG SUP board TRIPLE ACTION it's more compact and light. It's the best for brands who want to use a pump of triple action as standard equipment in their SUP. The compact piston permits also females and young guys to be able to achieve easily high pressure. HP6, being used in TRIPLE-doublesingle action, can achieve 30psi rapidly and effortlessly. The switching 3-2-1 can be realized easily and comfortably rotating the switch knob. Itâ??s completely customizable for colour, graphic and calibration of gauge meter. Features: · capacity 3.2+3.2L, max. pressure 30psi as DIN EN 16051 · switch knob to change comfortably from triple to double or single seals and anti-sand filter for long life of pump and SUP extra long body and high-airflow piston for an easier inflation pump completely shock-proof, compact and light (1.7kg) · shockproof gauge meter
Pump pv22, Used Korean Hyundai & Kia engine with gearbox, Organic Fertilizer, Used Volvo And Scania Engine With Gearbox, Arnold Palmer Golf Shoes.
Fly ash, fertilizer, seeds, agriculture pump, (electric pump and water pump) nozzle and pipe lance all types of coal.
LAH SERIES SLURRY PUMP Centrifugal Slurry pump centrifugal Heavy Duty Slurry Pump Type LAH pumps are cantilevered,horizontal,centrifugal slurry pumps.They are designed for handling abrasive,high density slurries in the metallurgical,mining,coal,power plant,building material and other industrial departments. The pumps of this type also can be installed in multistage series. The series of the pumps are of double casing.The liners are made from high chrome alloy as well as rubber and elastomer. The shaft seals forms of the series of the pumps can be adoptable of gland seal,centrifugal seal and mechanical seal.The discharge pipes can be positioned at intervals of 45 degree by request and oriented to any eight position to suit installation and applications. The capacity of the HEAVY DUTY SLURRY PUMP can reach 3600m3/h, the head of the pump can reach 80 m. The discharge pipe can reach 16 inches. The main product slurry pump is of 20 series, 80 varieties and more than 400 specifications, such as slurry pump, tailing slurry pump, sand gravel pump and dredge pump all can we product. For more information on pumps, please click here.
Chart recorders Gas analysing meters & detectors Load cells & display units. Instrumentation: flow, level & pressure control equipment for all industrial processes & mediums Vacuum switches generators & pumps Pressure gauges
Sewage Pump
