Find Verified Sae4140 Alloy Steel Bar Manufacturer In China Suppliers, Manufacturers and Wholesalers

We have a wide variety stock of rebar, available dimensions from 8 mm to 32 mm,grades 60,40 ASTM A615,and BS4449, lengths 4,5,6,9,and 12 meters,plain,and deformed bars. Material SD390/490/400,B500B/GR460B,HRB400/500,ASTM A615 GR40/60 Standard BS4449,JIS,ASTM/A615 Length 6m,12m Application Widely used in construction industry.

We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.

Material SD390/490/400,B500B/GR460B,HRB400/500,ASTM A615 GR40/60 Standard BS4449,JIS,ASTM/A615 Length 6m,12m Application Widely used in construction industry for reinforcing concrete(Express way; office building, Bridge etc) Transportation By sea(20' 40' container)

We are supplier of Reinforcement Bars. can supply REBARS as per below: -Size: 6mm to 50 mm -Length: 6 meters up to 16 meters -Packing: Once folded bundles available. hese corrugated steel bars are used as tension devices in the construction of concrete slabs and walls, as well as decorative/ornamental grille work. When used in concrete constructions, these help to strengthen and hold concrete when it is compressed, and come in a wide variety of sizes to fit various building construction needs. At ARC. AVAILABLE IN 3/8 (10mm), 5/8 (16mm), (20mm), (12mm), 1 (25mm) and 1 (32mm)

Classification : Monel Alloy 1.According to the preparation process can be divided into deformation superalloys, casting superalloys and powder metallurgy superalloys. 2. According to the strengthening mode, there are solid solution strengthening type, precipitation strengthening type, oxide dispersion strengthening type and fiber strengthening type, etc.

We are supplier and exporter of TMT Rebars. TMT Bars / Rebar which find usage in the core infrastructure development like construction of Multi Storeyed buildings, bridges, dams, railways, power plants as reinforcement material. These bars are rolled from Tested billets as per IS 2830 which ensures uniform physical and mechanical properties. The range varies from 8mm to 32mm, conforming to BIS 1786 - Fe 415 and Fe 500. Properties Units IS : 1786 Fe 415 OUR BARS IS: 1786 Fe 500 OUR BARS

192 is the steel of carbon structural steel, which is a kind of alloy steel and carbon steel. The carbon content is about 0.05%~0.70%, and some can reach up to 0.90%. It can be divided into ordinary carbon structural steel and high-quality carbon structural steel. Now the common round steel processes are hot rolling, forging and cold drawing. The steel quality and application scope of these three processing modes will also have some differences. For example, the specification of hot rolling is generally 5.5-250MM, and the appropriate steel can be selected according to the actual needs. Generally, parts are manufactured by machinery or used as seamless steel pipe blanks, and steel is also used in some building construction. Round steel has relatively high strength, high hardenability and very good toughness, so its pressure bearing capacity is also guaranteed. Even if it is used at high temperature, the creep strength is high and the durability is also guaranteed. Material A192 Thickness 0.1mm-300mm or as required Standard AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique Hot rolled,cold rolled Surface Treatment Clean, blasting and painting according to customer requirement Thickness tolerance �±0.1mm Application It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time Within 7-15 workdays after receiving deposit or L/C Export packing Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity 250,000 tons/year Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts. Warehouse Storage Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project.

Performance and application of material ST37: the material has good performance, that is, through cold rolling, it can obtain cold rolled strip and steel plate with thinner thickness and higher precision, with high straightness, high surface finish, clean and bright surface of cold rolled plate in Taiwan Strait, easy to be coated, various varieties, wide application, high stamping performance, non aging, and low yield point. Now the common round steel processes are hot rolling, forging and cold drawing. The steel quality and application scope of these three processing modes will also have some differences. For example, the specification of hot rolling is generally 5.5-250MM, and the appropriate steel can be selected according to the actual needs. Generally, parts are manufactured by machinery or used as seamless steel pipe blanks, and steel is also used in some building construction. Round steel has relatively high strength, high hardenability and very good toughness, so its pressure bearing capacity is also guaranteed. Even if it is used at high temperature, the creep strength is high and the durability is also guaranteed. Material ST37 Thickness 0.1mm-300mm or as required Standard AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique Hot rolled,cold rolled Surface Treatment Clean, blasting and painting according to customer requirement Thickness tolerance �±0.1mm Application It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time Within 7-15 workdays after receiving deposit or L/C Export packing Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity 250,000 tons/year Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts.

size upon request

Produced by Chongqing Hesheng Longgang Technology Co., Ltd. (manufacturer) Basalt fiber reinforcement (new material to replace reinforcement) Product Description: basalt fiber reinforced bar (BFRP) is a new composite material formed by pultrusion process. It is made of basalt fiber as reinforcement, resin, filler and curing agent. Now it has been widely used in construction, highway and bridge constructionã?? Basalt fiber reinforcement can completely replace ordinary steel reinforcement and deformed steel; Compared with ordinary reinforcement, it has strong advantages: (see Annex for technical parameters) 1. The cost is the same as that of ordinary reinforcement; 2. The strength is 200% of the ordinary reinforcement with the same specification and diameter; The tensile strength reaches 1100mpap; The reinforcement is only 450MPa, 3. Basalt fiber reinforcement, especially with high acid, alkali and corrosion resistance, is a kind of electrical insulator that will never rust. 4. Basalt fiber reinforced bar, which is non-magnetic. It has high tolerance to the moisture concentration in cement mortar and the penetration and diffusion of carbon dioxide, and can prevent the corrosion of concrete structure in harsh environment, so as to improve the durability of buildings and bridges. 5. The specific gravity of basalt fiber reinforcement is 2.1g/cm3; The specific gravity of steel and reinforcement is 7.85/cm3; The diameter weight of the same specification is 370% lighter than that of steel reinforcement, and the strength is 200% of that of steel reinforcement. 6. The physical properties of basalt fiber reinforcement are higher than that of steel reinforcement, and the cost is the same as that of steel reinforcement, which is of epoch-making significance to replace steel reinforcementã??

Special Use: Cold Heading Steel Wire Gauge: 1.8mm-5.5mm Application: Construction Alloy Or Not: Is Alloy Type: Galvanized Place of Origin: India and China

Standard : JIS, AISI, ASTM, GB, DIN, EN, BS ETC. Material 201 301304L 309S 316L310S321410 4302205 2507 904L INCOLOY Alloy HASTELLOY MONEL etc Specifications Round bar Diameter : 0.1~500mm Hexagonal bar Size : 2mm~100mm Flat bar Thickness : 0.3~200mm Width : 1~2500mm Square bar Size : 1mm*1mm~800mm*800mm Length : 2m, 5.8m, 6m, or as required. Surface : Black, peeled, polishing, bright, sand blast, hair line, etc. Price Term : Ex-work, FOB, CFR, CIF, etc. Export to : Singapore, Canada, Indonesia, Korea, USA, UK, Thailand, Peru, Saudi Arabia, Viet Nam, Ukraine, Brazil, South Africa, etc. Delivery Time : Standard size is in stock,prompt delivery or as order's quantity. Package : Export standard package, bundled or be required. The inner size of container is below: * 20ft GP: 5.9m(length) x 2.13m(width) x 2.18m(high)about 24-26CBM * 40ft GP: 11.8m(length) x 2.13m(width) x 2.18m(high) about 54CBM * 40ft HG: 11.8m(length) x 2.13m(width) x 2.72m(high) about 68CBM Use of stainless steel round bar: 1. It is used to manufacture self tapping screws such as bolts and nuts; 2. Used for manufacturing rivets; 3. Used for making spring steel wire and transmission mechanism parts; 4. It can be used for filling and strengthening in welding materials; 5. Main parts and components that can be used to manufacture molded articles; 6. It can be made into welded pipe for deep processing of seamless steel pipe or raw material of seamless steel pipe. 7. It is widely used in petroleum, chemical, food and other industries 8. It can also be used in shipbuilding, boiler and pressure vessel manufacturing, etc. 9. Mainly used for automobile parts: axle parts, such as automobile half axle sleeve and various small bearing shells 10. Mainly used for bicycle accessories: bicycle frame tube and various frame joints 11. Widely used in hardware products factories and machinery manufacturers 12. Widely used in various vehicle parts 13. Wide application and furniture decoration industry 14. Widely used in various mechanical equipment 15. Widely used in various pipelines 16. Widely used in various construction machinery 17. Applied to household appliances 18. Applied to electronic communication equipment

* Ordinary low alloy steel is a kind of ordinary alloy steel containing a small amount of alloy elements (in most cases, the total amount of w does not exceed 3%). This kind of steel has high strength, good comprehensive properties, corrosion resistance, wear resistance, low temperature resistance, and good cutting and welding properties. * Under the condition of saving a lot of rare alloy elements (such as nickel and chromium), usually 1 t ordinary low alloy steel can be used for 1.2-1.3 carbon steel, and its service life and scope of use are much longer than carbon steel. Ordinary low alloy steel can be smelted in open hearth furnace and converter with general smelting method, and the cost is close to that of carbon steel. Material : API5L Thickness : 0.1mm-300mm or as required Standard : AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique : Hot rolled,cold rolled Surface Treatment : Clean, blasting and painting according to customer requirement Thickness tolerance : �±0.1mm Application : It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time : Within 7-15 workdays after receiving deposit or L/C Export packing : Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity : 250,000 tons/year * Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts.

Material * ASTM(1005,1006,1008,1010,1015,1020,1025,1030,1035,1040,1045,1050,1055,1060,1065,1070,1080,1084,1016,1022) * DIN(Ck10,Ck15,Ck22,Ck25,Ck30,Ck35,Ck40,Ck45,Ck50, 30Mn4,40Mn4) * BS(040A04,095M15,045M10,080A40,045M10,080M50) * Thickness : 0.1mm-300mm or as required * Standard : AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. * Technique : Hot rolled,cold rolled Surface Treatment * Clean, blasting and painting according to customer requirement Thickness tolerance + 0.1mm * Application : It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. * Shipment time : Within 7-15 workdays after receiving deposit or L/C Export packing : Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity : 250,000 tons/year * Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts Warehouse Storage * Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project.

* A179 is a steel grade produced according to American ASTM standards, which belongs to American standard. A179 Carbon steel round bar is applicable to cold drawn high-quality low-carbon seamless steel pipe for heat exchanger and condenser. * Now the common round steel processes are hot rolling, forging and cold drawing. The steel quality and application scope of these three processing modes will also have some differences. For example, the specification of hot rolling is generally 5.5-250MM, and the appropriate steel can be selected according to the actual needs. * Generally, parts are manufactured by machinery or used as seamless steel pipe blanks, and steel is also used in some building construction. Round steel has relatively high strength, high hardenability and very good toughness, so its pressure bearing capacity is also guaranteed. Even if it is used at high temperature, the creep strength is high and the durability is also guaranteed. Material : A179 Thickness : 0.1mm-300mm or as required Standard : AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique : Hot rolled,cold rolled Surface Treatment : Clean, blasting and painting according to customer requirement Thickness tolerance : + 0.1mm Application : * It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time : Within 7-15 workdays after receiving deposit or L/C Export packing : Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity : 250,000 tons/year * Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts. Warehouse Storage * Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project

* A53 is a steel grade produced according to American ASTM standards, which belongs to American standard. A53 Carbon steel round bar manufacturing requires parts with low stress and high toughness, such as car body, container, deep stamping vessels, pipes, gaskets, etc., which can be used for cold rolling, cold punching, cold heading, cold bending, hot rolling and other processes, as well as carburizing parts with low central strength, carbonitriding parts, etc. * Now the common round steel processes are hot rolling, forging and cold drawing. The steel quality and application scope of these three processing modes will also have some differences. For example, the specification of hot rolling is generally 5.5-250MM, and the appropriate steel can be selected according to the actual needs. * Generally, parts are manufactured by machinery or used as seamless steel pipe blanks, and steel is also used in some building construction. * Round steel has relatively high strength, high hardenability and very good toughness, so its pressure bearing capacity is also guaranteed. Even if it is used at high temperature, the creep strength is high and the durability is also guaranteed. Material : A53 Thickness : 0.1mm-300mm or as required Standard : AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique : Hot rolled,cold rolled Surface Treatment : Clean, blasting and painting according to customer requirement Thickness tolerance : + 0.1mm Application : It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time : Within 7-15 workdays after receiving deposit or L/C Export packing : Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity : 250,000 tons/year * Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts.

* A214 is a steel grade produced according to American ASTM standards, which belongs to American standard. * Now the common round steel processes are hot rolling, forging and cold drawing. The steel quality and application scope of these three processing modes will also have some differences. For example, the specification of hot rolling is generally 5.5-250MM, and the appropriate steel can be selected according to the actual needs. * Generally, parts are manufactured by machinery or used as seamless steel pipe blanks, and steel is also used in some building construction. Round steel has relatively high strength, high hardenability and very good toughness, so its pressure bearing capacity is also guaranteed. Even if it is used at high temperature, the creep strength is high and the durability is also guaranteed. Material : A214 Thickness : 0.1mm-300mm or as required Standard : AISI,ASTM,DIN,BS,JIS,GB,JIS,SUS,EN,etc. Technique : Hot rolled,cold rolled Surface Treatment : Clean, blasting and painting according to customer requirement Thickness tolerance : + 0.1mm Application : It is mainly used to make structural parts such as car girder, beam, transmission shaft and car chassis parts, which can reduce the weight of the parts. Shipment time : Within 7-15 workdays after receiving deposit or L/C Export packing : Waterproof paper, and steel strip packed. Standard Export Seaworthy Package.Suit for all kinds of transport,or as required Capacity : 250,000 tons/year * Round steel belongs to carbon structural steel for construction and machinery, while square steel belongs to carbon structural steel for machinery. Both of them are simple section steel, and their section shapes are respectively round and square. Low carbon is mainly used for drawing wire, forging rivets, bolts, nuts and other metal products of raw materials. Medium carbon round steel and square steel are generally used to make mechanical structural parts.