Opgw Performed Helical Suspension Clamp Suppliers and Manufacturers

The unique design of the lightweight HuaNeng Fitting mechanical suspension supports spans of optical ground wire (OPGW) cables through a wide range of line angle variations. HuaNeng Fitting's mechanical suspension is easy to install while supporting vertical, lateral, and longitudinal unbalanced loads and angular tension without damaging cable strands or affecting fiber performance. Separate bolts Composition inner twisted wire, Outer twisted wire, Rubber block and cast aluminum shell. Uses To play a supportive role, the optical fiber composite overhead ground wire (OPGW) are hung on a straight line on the tower.

OPGW Performed Helical Suspension Clamp The unique design of the lightweight HuaNeng Fitting mechanical suspension supports spans of optical ground wire (OPGW) cables through a wide range of line angle variations. HuaNeng Fitting's mechanical suspension is easy to install while supporting vertical, lateral, and longitudinal unbalanced loads and angular tension without damaging cable strands or affecting fiber performance. Separate bolts OPGW Suspension Clamp Suspension clamps are also known as overhanging wire clamps or overhanging fixtures. According to the use, opgw suspension clamp include ABC cable overhanging wire clamps, ADSS cable overhanging wire clamps, and overhead line overhanging wire clamps. Suspension wire clamp is a general term for all types of wire clamps that suspend wires or cables from a pole tower. Pre-twisted opgw cable clamps are used for the connection of OPGW cables and towers to reduce the static stress at the support point of OPGW cables, to improve the vibration resistance of ADSS cables, to buffer the dynamic stress of wind vibration, and to ensure that the cable bends within the permissible value, so that the cable does not produce bending stress, so that the optical fiber does not produce additional loss in the cable after installation.

Model: AXD1280 Suitable ADSS diameter: 10.1 -11 mm Application span: max 150m Hot dip galvanizing per ISO 1461

An OPGW (Optical Ground Wire) tension clamp is a specialized device used in the installation and maintenance of OPGW cables. OPGW cables are composite overhead cables that combine optical fibers for communication purposes with a metallic ground wire for power transmission and grounding. The OPGW tension clamp serves the purpose of securely attaching the OPGW cable to the supporting structure, such as poles or towers, while maintaining the necessary tension. It plays a crucial role in ensuring the stability and reliable performance of the OPGW system. Here are some functions of an OPGW tension clamp: Cable Gripping: The tension clamp is designed to securely grip the OPGW cable to prevent it from slipping or becoming loose. It typically consists of specially designed jaws or grips that firmly hold the cable in place. Tension Adjustment: The clamp allows for adjustment of the tension applied to the OPGW cable. This feature is important to maintain the desired tension level in the cable, which is essential for its proper functioning and mechanical stability. Mechanical Strength: OPGW tension clamps are constructed using robust and durable materials, such as stainless steel or aluminum alloy, to provide high mechanical strength. This ensures that the clamp can withstand the tension forces exerted on the cable and withstand environmental conditions, such as wind and ice loading. Electrical Continuity: The tension clamp also maintains the electrical continuity of the metallic ground wire within the OPGW cable. It provides a reliable connection between the cable and the supporting structure, ensuring effective grounding and electrical performance. Corrosion Resistance: OPGW tension clamps are often designed with corrosion-resistant coatings or materials to withstand exposure to harsh outdoor environments, including moisture, UV radiation, and temperature variations.

Description ADSS preformed tension clamp is designed for connecting and fastening the ADSS fiber to the overhead pole. Feature 1) quick and easy installation 2) distribute the stress uniformity 3) guarantee no cable damage or slipping 4) strong resistance to corrosion and cruel environment 5) made of aluminum alloy, aluminum clad steel and galvanized steel Order Tips 1- confirm the cable type 2- confirm the cable diameter 3- confirm the span and the rated tensile strength 4- the material can be aluminum alloy, aluminum clad steel or galvanized steel Our service 1, Fast Response Time 2, Quality and Certified Products3, Resonable Price 4, Cheap and Reliable Transportation 5, 7*24 Hours After Sales Service

NFC standard Suspension Clamp for LT and HT AB Cable.

Model Number:JH-082 Product name: suspension clamp Brand Name:Jinhan Type:XGU-1 standard:GB Application:broad Material:aluminum produce according to customers'drawing and requirement samples available package cartons & pallets according to customers' requirement

Qucik detail Place of Origin Zhejiang, China Brand Name CROP Model Number Suspension clamp Product name ABC suspension clamps for self supported Sample Supply Free Material Plastic Installation Quick Certifications ISO9001 OEM Acceptable Export All over the world Business Type Manufacturer

Preformed tension clamp is also called preformed dead end or dead end cable clamp. The raw material of preformed tension clamp is aluminum clad steel wire or galvanized steel wire, For communication ADSS optical fiber, OPGW cable and OPPC. The unique pre-formed tension clamp design not only simplifies the installation but also ensures the safety of the cable connection. Terminal cable clamps provide excellent performance to protect ADSS/OPGW/OPPC cables from stress points and prevent signal drops during transmission. What is the raw material of the pre-formed tension clamp The raw material of the prefabricated tension clamp is aluminum-clad steel wire or galvanized steel wire. What is the purpose of prefabricated tension clamps Prefabricated tension clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. What are the types of prefabricated tension clamps The preformed tension clamp and guy wire dead end grips used on the conductor and earth wire look alike in shape, but there are really big differences in the specification, raw material, and strength requirement of the two types of guy grips. 1. Dead-end for short span ADSS Dead-end for short span ADSS with a small tension clamp material for aluminum-clad gang wire, mainly used for the corner towers, the middle of follow-tower and connecting the terminal tower, the largest installation file from the less than 100 meters. 2. Dead-end for medium/long span ADSS Dead-end for medium span ADSS in tension and large tension clamp material for aluminum-clad steel wire, mainly used for files larger than 100 meters away from the corner tower, the middle tower and Terminal Tower successive connection. As an experienced manufacturer and supplier of preformed tension clamps, Boersen Photoelectric is able to OEM to customer specifications. If you have any questions, please feel free to contact us.

Dead end grip for OPGW Component Inner armor rods, outer armor rods, thimble, U-shaped hanging loop, Extensioe Rods, bolt, nut, etc. Characteristic 1. Stress is distributed equally, without stress focus. It can protect optical cabl-es very well. 2. Under the condition of not exceeding the intensity of cable's side pressure, it has higher grip power for the cable, and can support higher tensile force. 3. The grip power for the cable is not less than 95% of rating's pulling resisting intensityof the optical cable, completely satisfying the needs of setting up the cable. Conditions For The Usage 1. Terminal poles/towers; 2. Corner poles/towers; 3. Dead-end poles/towers; Intensity According to the requirement of customers, 30kN, 70kN, 100kN, 120kN, etc, can be supplied. Select Chart Model Grip(KN) Length of Inner Armor Rods(mm) Length of Outer Armor Rods(mm) Estimated Weight(KG) Color ONZ-60-* * 60 1900 1500 2.9 Yellow ONZ-70-* * 70 2000 1600 3.5 Yellow ONZ-80-* # 80 2200 1700 4.2 Yellow ONZ-90-* # 90 2400 1800 4.3 Yellow ONZ-100-* # 100 2500 1900 4.5 Yellow ONZ-120-* # 120 2600 2000 5.0 Yellow Note: representing the outer diameter of the optical cable (mm).

ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.

ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.

Wholesale ADSS Suspension Clamp An ADSS (All-Dielectric Self-Supporting) Suspension Clamp is a component used in the installation of ADSS fiber optic cables. ADSS cables are designed to be self-supporting and do not require any metallic elements for support, making them suitable for aerial installations in various environments, including power distribution lines, railways, and more. The suspension clamp is an essential part of the ADSS cable installation process, as it helps secure the cable to the supporting structures, such as poles or towers. The primary purpose of the ADSS suspension clamp is to maintain the appropriate tension on the cable while preventing excessive bending or stress that could negatively impact the cable's performance and longevity. ADSS suspension clamps are typically made of materials that are durable and resistant to environmental factors such as UV radiation, extreme temperatures, and moisture. They are designed to hold the ADSS cable securely in place while minimizing stress and strain on the cable itself. The installation process of ADSS suspension clamps involves attaching them to the support structure and then securing the ADSS cable in the clamp. This process ensures that the cable is held in the correct position and tension, optimizing its signal transmission capabilities and overall reliability. Features Durable Construction: ADSS suspension clamps are typically made from materials that are resistant to environmental factors such as UV radiation, extreme temperatures, and moisture. This durability helps ensure the longevity of the clamp in various outdoor conditions. Corrosion Resistance: The materials used in the construction of ADSS suspension clamps are often chosen for their resistance to corrosion, preventing degradation over time due to exposure to harsh weather conditions.

Qucik detail Place of Origin Zhejiang, China Brand Name CROP Model Number J hook suspension clamp Product name J hook suspension clamp for self supported twisted conductors Sample Free Material Aluminum,Copper