Find Verified Hydraulic Manifold Blocks Suppliers, Manufacturers and Wholesalers

Only AAK was able to produce the hydraulic manifold blocks, and its technology is not inferior to American and Japanese counterparts

Scott comes from an equipment company in the United States. In the second half of last year, they developed a hydraulic equipment to be introduced at the exhibition. The chief engineer of the company requires the purchasing department to get all hydraulic manifold blocks arrive at the factory within 3 months. There is a hydraulic manifold block. Due to the slow production, the production time of 45 days is not enough. Scott disassembled the hydraulic manifold blocks, purchased the hydraulic valve blocks from one factory and the hydraulic cartridge valves from another factory. All hydraulic manifold blocks and those parts produced separately arrived at the factory in the United States in 3 months. The technicians in the workshop installed them. After a few days of commissioning, they found that there were oil leakage on one hydraulic manifold block, that is the one disassembled and produced in two different factories. The chief engineer requires getting a new hydraulic manifold block within 1 month, otherwise it will be too late to catch the exhibition.

Scott contacted the original manufacturer. As a result, the two hydraulic valve manufacturers prevaricated each other. Their engineers also tested the hydraulic cartridge valves and hydraulic valve blocks separately, and there was no abnormality. Scott tried to contact new manufacturers of hydraulic manifold blocks, but they all said that they couldn't get samples ready within 30 days. Scott was worried.

Scott saw on AAK website that a hydraulic manifold block was very close to the size he wanted to purchase, so he sent an inquiry. After two rounds of communication, we learned about the problems he encountered in purchasing hydraulic manifold blocks. I told him that if the hydraulic cartridge valves and the hydraulic valve blocks were approved to be no problem, the workshop technician might break the seal ring or shift the seal ring during the installation of the hydraulic manifold blocks. This kind of hydraulic manifold blocks purchased from different manufacturers and then assembled is easy to have problem. A customer of AAK encountered similar problems before. After Scott asked their mechanic to replace the sealing ring, there was no abnormality in the test run, and they could catch up with the exhibition. Scott is glad that the problem of hydraulic manifold block has been solved, and said that for all hydraulic equipment orders after the exhibition, the hydraulic manifold blocks will be purchased from AAK, and also asked us to send hydraulic manifold blocks with similar dimensions to the United States to test stability and service life.

For the Hydraulic Manifold Block with porous system like cranial nerve, after made samples successfully,
They have a special hydraulic manifold block, which includes 13 groups of M32 threaded holes, and all of them are stepped holes. At the same time, there are cross holes, straight holes, and bypass holes. The hole size is required to be more than 8. Compared with the hydraulic manifold blocks with 10 groups of normal threaded straight holes, it is not only complex in structure, but also 20% higher in precision. Arno knew that it was difficult, so he arranged 3 hydraulic manifold block manufacturers for proofing, which lasted 60 days, but all of them failed to meet the standard. This is a test order of hydraulic manifold block from an old customer. Arno wants to struggle again. Due to time constraints, he does not dare to use a new hydraulic manifold block manufacturer. His old hydraulic manifold block supplier is also unreliable. This makes , who has eight years of procurement experience, a little overwhelmed.

I had a hunch that this hydraulic manifold block was not simple. Because the PO of hydraulic manifold blocks given to me by is a challenge every time. engineers pondered over the drawing of hydraulic manifold block sent by , and it is really difficult to process, with very high precision. There are not only many pore systems, but also many deep holes, more than 20 groups of 4 deep holes, with a length diameter ratio greater than 25. For M32 threaded holes of stepped holes, the coaxiality between holes is required to be 0.02mm, and the coaxiality between threads and holes is required to be 0.045mm. This complex pore system structure is like the distribution of the nervous system of the human brain. Doctors without more than 10 years of experience in brain surgery may not be confident to operate on the operating table.

technical team, after 3 days of internal research and discussion, the plan has been worked out, and our chief engineer will handle the knife, starting from the production drawing of the hydraulic manifold block. However, I replied to that was only 90% sure that the sample of this hydraulic manifold block was successful, and the cost was not low. Maybe hesitated and didn't give any reply for 3 days. On the fifth day, received the development fee paid by him.

How does Chinese Hydraulic Manifold Manufacturer AAK ensure the reliability and longevity of the machining quality of hydraulic manifold blocks?

AAK customizes hydraulic manifold blocks for customers in multiple countries, including Germany, the United States, Russia, and Israeli military clients.

We strictly control the selection of materials, processing techniques, surface treatment, cleaning, and inspection to ensure the reliability and longevity of hydraulic manifold blocks like below:

1. Materials and Pretreatment
1) Material Selection
The valve block material should have a dense structure and be free of defects such as sand holes and interlayers. If necessary, non-destructive testing should be carried out.
If forging blanks are used, they need to undergo normalizing treatment to eliminate internal stress and non-destructive testing.
2) Pretreatment
Cast iron or large steel parts require aging treatment or pretreatment.

2. Machining process
1) Surface processing
The surface roughness of the hydraulic valve block must meet the design requirements, and the installation surface (such as the contact surface of hydraulic valves and pipe joints) must not have scratches to prevent leakage
Rough machining requires reserved precision grinding allowance, and the surface roughness Ra value after precision machining should meet the accuracy requirements.
2) Chamfering and deburring
Edge chamfer 2 45 (small valve body chamfer 45 ), keep the oil passage hole sharp and remove burrs.
All flow channels (especially intersections) need to be thoroughly cleaned of burrs to avoid residual effects on system stability.

3. Surface treatment and rust prevention
1) Coating and Marking
The surface can be plated with electroless nickel, with a thickness controlled between 0.008-0.012mm.
Steel seal markings should be placed next to each oil port, with a distance of �¢?�¥ 6mm from the hole opening, to avoid affecting the sealing performance.
2) Rust prevention measures
After processing, rust and dust prevention treatment should be carried out, and sealed and stored in a clean and dry environment.

4. Cleaning and assembly
1) Cleaning
Before assembly, the manifold block should be thoroughly cleaned using rust proof cleaning solution or kerosene/engine oil to ensure that blind holes and flow channels are free of iron filings and impurities.
Maintain pressure during flushing, and switch the solenoid valve to flush all channels.
2) Assembly
Check if the connectivity of the ducts is consistent with the schematic diagram, ensuring that the seals and components are all qualified products.
When using anaerobic adhesive to seal screws, it is necessary to clean the joint surface and let it stand for 24 hours before applying oil.

5. Inspection and Testing
1) Inspection
After processing, it is necessary to check the dimensional accuracy of oil ports, threads, counterholes, etc.

This morning, Joselito sent an email asking about the production time of 1,000 hydraulic manifold blocks, which surprised me a little, because in the past two years, Joselito has basically placed orders for just hydraulic valves only, but very few for the hydraulic manifold blocks. Joselito is a purchaser of BEZARES company in Spain. We met 2 years ago. After communication, it was learned that he encountered problem on the hydraulic manifold blocks purchased this time.

A batch of hydraulic winch equipment of their company was complained by some users that the winch was often weak. Their after sales found that the hydraulic manifold block was leaking. Because of the purchase cost limitation, he disassembled the hydraulic manifold blocks and purchased them separately from 3 hydraulic valve manufacturers. Now the leakage problem of the hydraulic manifold blocks has come, all 3 manufactures prevaricate and are not responsible for the oil leakage of the hydraulic manifold blocks, they thought that the problem was caused by the unreasonable design or the wrong installation method of the hydraulic manifold blocks. The engineer checked the hydraulic manifold blocks one by one and found different problems, some sealing ring was broken, some gasket at the interface was worn, and some has iron filings in the valve hole. In the past year, a lot of money, labor and maintenance costs were spent on the after-sales for the hydraulic manifold blocks. Now the customers are not satisfied with their after-sales performance, and the boss is not happy to spend the after-sales money indiscriminately. Joselito has a big headache.

AAK suggests that Joselito should purchase the whole hydraulic manifold blocks in one factory as much as possible, because each hydraulic valve manufacturer has different quality positioning. AAK has now received more and more inquiries for hydraulic manifold blocks, including Skyjack, a Canadian listed company, and Brevini, a top company in the field of transmission.

Joselito finalized the purchase contract of the hydraulic manifold blocks with AAK in two rounds, and required that AAK hydraulic manifold blocks should not be reported for repair within 1 year. It is not only the hydraulic valves and hydraulic manifold blocks produced by AAK with quality assurance, but also 3 points that are difficult for peers to do well:

1. AAK shall deeply clean the hydraulic manifold blocks before assembly to ensure that it is 100% free of iron filings, dirt and other impurities.

2. Only technicians with more than 10 years of experience are qualified to assemble, check the matching between the duct and the hydraulic schematic diagram, and test the accuracy of each duct to ensure that the sealing ring of the hydraulic valves will not be damaged. After assembly, use the test bench to debug the hydraulic manifold blocks for many times, including pressure test and function test,

With hydraulic manifolds, the energy consumption of the original unsalable equipment not only decreased by 20%, but also became hot seller
is from a agricultural machinery equipment company, mainly responsible for purchasing hydraulic components. In the second half of last year, the sales of one of their rotary tillers were poor. Users reported that the equipment was insensitive and inefficient, and the fuel consumption was 10% higher than that of the same type of equipment. The boss realized that there were hidden dangers in the hydraulic manifolds and asked the engineers to check the causes. However, more than 1 month had passed and there was no practicable plan. The boss was worried and asked to contact the original hydraulic manifold manufacturer to see if they could provide technical support, but they were only good at producing hydraulic manifolds according to the drawings. Connor also asked all his manufacturers of hydraulic components, but none of them gave a plan. When reported these to his boss, he could only helplessly look at his boss shaking his head.

the display and introduction of hydraulic manifolds, and left a message: what is the relationship between hydraulic equipment with high energy consumption and slow response and hydraulic manifolds I understood that Connor had a problem with hydraulic manifolds, but it was difficult to answer. After several communications, I learned that his boss was worried, and wanted to solve the problem that had plagued his company for nearly 3 months.

According to the hydraulic manifold drawings and the video of rotary tiller work sent by engineers had discussion. The probability was that the hydraulic manifold design had hidden problems. From the analysis of hydraulic manifold and system schematic diagram, there were certain energy conflicts between the design of some oil circuits and the selection of hydraulic valves. could redesign the hydraulic manifold to match their equipment. also readily paid the development cost. 1 month later, sent the hydraulic manifold samples. 2 months later, said that after their rotary tiller was installed with hydraulic manifolds, it was responsive during operation. The operation was more than 20% higher than before, and the fuel consumption was also reduced by 20%. The customer feedback was good, and more and more customers came to try it out.

told me privately that he had seen his boss's long lost smile. The boss paid more and more attention to him. He will be promoted to the management next month.

hydraulic manifold has 3 advantages
1. engineers have experience in hydraulic manifold design, especially in oil circuit design. Ensure flow distribution as required, eliminate bypass throttling loss and reduce energy loss.

Increase the equipment efficiency by 11% and reduce the energy consumption by 30%. AAK exclusive hydraulic manifold has no rival

At the beginning of March this year, Bartolomeo said in an email that he would like to make an appointment to consult AAK about hydraulic manifold problems. Bartolomeo, from Italy, is the purchasing manager of Italpresse Industrie Shanghai Branch. According to the communication, their company developed a hydraulic die-casting machine at the end of last year. The sales volume is just so. The general feedback is that the equipment has high energy consumption and low production efficiency. Their engineers pondered for more than 2 months, but couldn't find the reason, and the boss also had a big headache. Bartolomeo felt that the hydraulic manifold design dragged down the equipment and consulted the original hydraulic manifold manufacturer. However, the manufacturer could not put forward constructive opinions on the hydraulic manifold design.

Bartolomeo thought of AAK, because AAK had proposed to modify the oil circuit when receiving the inquiry about the hydraulic manifold. According to the design drawings and system schematic diagram of hydraulic manifold provided by Bartolomeo, AAK engineers closed the door and discussed for 3 days, basically found out the direction, and it is 90% determined that there was a deviation in the oil circuit design of the original hydraulic manifold on the hydraulic die casting machine. There is an energy conflict between the original hydraulic manifold oil circuit aperture and the hydraulic valve used, resulting in the slow response of the hydraulic system and the need for additional energy to maintain the operation of the system, resulting in high energy consumption and low production efficiency. AAK can redesign the hydraulic manifold oil circuit and send hydraulic manifold samples within 30 days. Bartolomeo was very happy that AAK found the cause of hydraulic manifold problem at once. The situation was fed back to the boss, who immediately paid for AAK to redesign and test samples.

A month later, AAK sent out the whole newly designed hydraulic manifold. Two weeks later, Bartolomeo emailed to order 20 hydraulic manifolds first to replace those ones on the equipment complained by customers. I was surprised that there was no comment on AAK hydraulic manifold samples but received the urgent order first. Bartolomeo advised that according to the comparison of their engineerâ??s on-site test run, the die casting machine with AAK hydraulic manifold has a sensitive response, the working efficiency is 11% higher than before, whatâ??s more, the energy consumption is reduced by 30%. Their boss asked to order some hydraulic manifolds for emergency use first, and then replace all hydraulic manifolds on the original equipment with AAK shipments.

Hydraulic Pay Off Stand

We are supplier and exporter of Hydraulic Oil.

Our product is a high quality product made from imported oils and additives of best quality. It has a very good life and will give the best performance under the most critical conditions. It is available in 210 ltrs. Hdpe drum/ 26 ltrs. And 50 ltrs.

Multi-brand Hydraulic Oils ISO VG 15, 32, 46, 68 and 100. Available in Drums, pails, IBCc, Bulk.

The hydraulic valve blocks designed and produced by not only has high reliability and small pressure loss to ensure that there is no oil running between the channels, but also has compact structure, small occupied space, simple oil circuit and easy pipe layout, so as to ensure the high efficiency requirements of different actions of various actuator elements. The valve block can control the valve, which is easy to adjust and operate. hydraulic valve block was designed and proofed successfully at one time within 1 month, which impressed the engineers o

The vast majority of hydraulic valve block manufacturers blindly proofed according to customer drawings, ignored working conditions, and did not understand the internal structure and working principle of hydraulic valve block. It is easy to cause hidden dangers in the hydraulic system, and the problem cannot be found.
power insensitivity of the hydraulic system related to the hydraulic valve block We replied that this is difficult to judge because it is a system problem that needs to be checked one by one. the next day then we understood why he left such

The power unit of a hydraulic system developed by his company needs a hydraulic valve block. Their engineers mentioned that the sensitivity of the power unit is the key and that all components need to cooperate closely. the hydraulic valve block manufacturer strictly controlled the accuracy according to the drawings, it could be easily done. After the hydraulic valve block is finished, it is installed to test the hydraulic power unit. After the oil pump is started, the instantaneous pressure supply at the oil outlet of the power unit does not come up, and it just supply normal pressure after a few minutes. After checking each component one by one, it is suspected that there are hidden dangers in the hydraulic valve block. After detecting the hydraulic valve block, there is no problem in the oil passage and channel of the hydraulic valve block the original hydraulic valve block manufacturer for analysis and solution. The manufacturer said that the hydraulic valve block was completely produced in accordance with the drawings and the accuracy was within the required range, and the reason for problem was unknown. hydraulic valve block , they all said that they could match the drawings, but not sure about the problems of the hydraulic valve blocks.

hydraulic system and the picture of the oil circuit running direction of the hydraulic valve blocks of the original have ideas after 3 aspects of comparative analysis.

- Product name: Tumi Ishi Wood Rock
- Color: Natural wood color
- Material: Pine Wood
- Shape and Size: Random
- Type: Other Educational Toys
- Usage: Relax and Educate

REMELTED ZINC BLOCK
ZINC 99.92%, ALU 0.002% , PB 0.003%, CD 0.002%, FE 0.003%

What are Tumi Ishi Wood Rocks?
Tumi Ishi wood rocks are an open-ended wood toy that will provide hours of relaxing, and challenging fun. These handmade blocks are great for boosting focus, and attention, and for promoting creativity
Tumi Ishi wood rocks are handmade and unique (no two blocks are the same). The blocks measure approximately 2 to 4 inches, and the weight of each block varies depending on the wood species

Solid particular board
Glue : E1/E2
100% Pinewood
Size : 44 mm 3x7
38 mm 3x7
33 mm 3x7

AAK's 3 tips to ensure that the Proportional Valve is free of jamming, winning the affirmation of customers in Turkey

Ewalz is from Turkey, and mainly purchases standard parts of hydraulic cartridge valves from Ningbo China. Recently, they developed a hydraulic manifold that requires the use of SUN proportional valves. He purchased it from a proportional valve manufacturer in Ningbo, and after 2 weeks of operation, the equipment experienced significant vibration. The on-site engineer found that the proportional valve was severely stuck. The original hydraulic valve manufacturer stated that this proportional valve is a replica of SUN, with fully calibrated parameters, but there are differences in performance. Ewalz was speechless and had to look for a new hydraulic valve manufacturer for this proportional valve.

Ewalz browsed the AAK hydraulic valve website, stayed for nearly 15 minutes and left a message:

1. Does AAK have an existing program for benchmarking SUN proportional valves?
2. Can AAK completely solve the problem of valve spool jamming, vibration and noise?

After communication, it was learned that the hydraulic manifold they developed was very tight on time, they had no time to customize it and could only choose the existing SUN proportional valve. The proportional valve produced by the original valve manufacturer has the same function as SUN, but has poor performance.

This SUN proportional valve is widely used, and AAK have a record of 6 shipments last year. There has never been any jamming of the valve spool, and we have inventory, which fully meets his requirements.

2 weeks after AAK sent the SUN proportional valve samples, Ewalz informed us via email that the hydraulic manifold debugging was successful. 2 months later, Ewalz informed us that their engineers were satisfied with the AAK proportional valve. The root cause of unsatisfactory performance of the original valve manufacturer's SUN proportional valve lies in its accuracy. The vast majority of proportional valve manufacturers have a cylindricity machining accuracy greater than 5um, which is 70% lower than the SUN standard cylindricity. For the accuracy of proportional valves that is completely in line with the SUN standard parts, there are probably less than 3 hydraulic valve manufacturers in Ningbo China. AAK controls the accuracy of the proportional valve from 3 aspects:

1. AAK proportional valve spool control: The valve spool is produced using a German CNC lathe with one blade and then high-precision cylindrical grinding. The machining error is controlled within �± 1um, and the coaxiality and cylindricity are controlled within 3um.
2. AAK proportional valve hole control: Adopting Swiss honing processing, the accuracy can reach IT6-IT7 level, and the surface roughness can reach Ra0.2-0.025um.

Refractory Burner Blocks are special type of Block which are form of Refractory ceramic material. It is used for Boiler, furnace, kiln, fireplaces & fireboxes.

Quality:
We offer various quality Burner Block are IS-6, IS-8, PI - 30% to 70% Alumina offering high temperature resistance of 1100 C to 1700 C & Special brick as per require technical data considering to application of Brick.

Sizes of Burner Block (Inch):
9 x 9 x 9
12 x 12 x 12
14 x 14 x 14
16 x 16 x 16

Recently, I received the second re-order of a hydraulic pressure reducing valve from French client Chinning. I still remember when I first met Chinning in 2020, Chinning purchased hydraulic pressure reducing valves in a hydraulic valve factory and encountered quality complaints from her customers. The hydraulic pressure reducing valve was deformed in less than 3 months, and some valve spools and valve sleeves were seriously worn. More and more customers began to return goods, and the old suppliers did not cooperate with her work. Chinning had a big headache at that time, and the owner kept putting pressure on her to find a hydraulic valve manufacturer with exquisite quality as soon as possible.

Chinning did not find a new hydraulic valve manufacturer very smoothly. Because her hydraulic pressure reducing valve had a special use scenario and required high hardness of materials, it was unbearable for ordinary factories. At the same time, under the environmental protection policy of 2019, many previous heat treatment and processing factories were shut down, so the supply supporting system was disrupted, and the heat treatment and processing of many hydraulic valve manufacturers could not keep up.

how does AAK ensure the service life of hydraulic valve products We didn't answer directly, but asked her if the hydraulic valves you purchased had the problem of deformation and rapid wear. She also replied quite frankly that she should find a hydraulic valve manufacturer that paid attention to the service life of hydraulic valves in the fastest time.

I sent her several samples of hydraulic pressure reducing valve and told her that different parts of our hydraulic pressure reducing valve have different material hardness standards, and some could reach about 50-55HRC or higher. There is even no problem with 65HCR with special requirements. The service life of hydraulic pressure reducing valve is our hard index.

More than one week after we sent out the samples of hydraulic pressure reducing valve, we received Chinning's email, including the drawings of hydraulic pressure reducing valve and the hardness requirements for various components. She asked whether we could produce this hydraulic pressure reducing valve? I told her that his hydraulic pressure reducing valve is not difficult, but just the working scene is some special. As long as the heat treatment process is a little unique, it could ensure her requirements. The long service life of hydraulic valve is the most critical.

At the beginning of last year, Lawrence sent an email to ask for help. He is a purchaser of a hydraulic equipment company in Italy and has cooperated with AAK for 2 or 3 years. Almost all of the orders are a small number of hydraulic check valves with high requirements. When encountering problems, he always asks for help from AAK, and AAK is also happy to help him. After several rounds of email communication, it turned out that the power unit for controlling the hydraulic lifting column produced by their company had a customer complaint 3 months after sales. Their engineers found a leak on the valve block of the power unit, that is, around the valve hole equipped with the hydraulic pilot operated check valve. It is preliminarily judged that the leakage should be caused by the wear of the seal of the hydraulic pilot operated check valve. However, after dismantling the hydraulic pilot operated check valve, it is found that the sealing ring is intact.

After Lawrence communicated with the original manufacturer of hydraulic pilot operated check valve, they both thought that there should be no problem with the hydraulic pilot operated check valve or valve block, because the test data before shipping were qualified. The leakage problem should be caused by the wrong operation of the installation personnel of their company. Lawrence seemed to understand because it is true that the test result of the hydraulic pilot operated check valve originally shipped was OK. Lawrence asked their engineers to reinstall it. As a result, it worked normally and everyone thought the problem had been solved. But 3 months later, the same problem happened again, and the customer could not accept and requested to return goods. The boss was very angry and asked Lawrence and the engineer to completely solve the leakage problem of the hydraulic pilot operated check valve. This is why Lawrence emailed to AAK for help.

AAK engineers analyzed according to the valve block integration diagram and the drawing of hydraulic pilot operated check valve provided by Lawrence. There is an assumption that the frequent vibration of the power unit of the hydraulic lifting column affects the stability of the installation of the hydraulic pilot check valve. Following this idea, it is found that the hole depth of the threaded socket integrated with the valve is not enough, which leads to the loosening of the jack position of the hydraulic pilot operated check valve. This problem can only be solved by adjusting the depth of the jack, increasing the thread torque of the hydraulic pilot operated check valve and increasing the bonding area between the valve and the hole. The next day I emailed Lawrence the idea of our engineer's. If we want to verify this idea, we can only make samples. One month later, AAK sent the redesigned hydraulic pilot operated check valve and integrated valve block to Lawrence.