Hydraulic Check Valve Suppliers and Manufacturers

He has done very well and occasionally inquires about the price with HYDRAULIC VALVE. For the hydraulic check valves purchased some time ago, the production director found that 20% of the hydraulic check valves have parameters that do not meet the standard, so they must get new qualified ones to the workshop within 20 days, otherwise the delivery of customer order would be delayed. Charles asked the original manufacturer of the hydraulic check valve to complete the replacement within 2 weeks. The manufacturer is willing to replenish, but the production can be started only after 15 days, that is to say, it will take 30 days to replenish. tried to find other suppliers of hydraulic check valves, and all replied that it could not be completed in such a short time. realized that something was going to happen and began to look for a new hydraulic valve manufacturer, contacting factories one by one. thought that had also participated in the quotation of this hydraulic check valve, and the samples provided also met the requirements, but it was not considered because the quotation of was slightly higher than that of other hydraulic valve manufacturers by 7%. sent us an e-mail to ask whether the quotation of hydraulic check valve offered 6 months ago can be maintained, and if we can finish an urgent order of 100 hydraulic check valves in 10-12 days. I felt that this should be an order for hydraulic check valve encountered with problem. told us the truth. About 20% of the hydraulic check valves produced by the original factory were unqualified and rejected by their production director. Now he must replenish them as soon as possible. General hydraulic valve manufacturers are unwilling to make such aftercare orders, but HYDRAULIC VALVE don't think so, because , as a production factory, has the same goal as the importer, that is to serve users well, so is more willing to help customers and solve complaints from users together. Fortunately, the corresponding materials are in stock. Combined with the 24-hour production line, our production director conservatively estimates that it can be completed in 12 days. asked us to start blanking now and the hydraulic check valve order will be issued tomorrow. After 10 days, 100 hydraulic check valves were successfully finished. was very happy and quickly air freighted these hydraulic check valves to the Thanks to the God, 100 hydraulic check valves finally arrived at their workshop in 20 days. informed us by email that their engineers installed, debugged and tested hydraulic check valves, which were all normal. The 7% higher price was also agreed by his owner. The owner was very amazed that can deliver so quickly and the quality was better than that of the original manufacturer.

a purchaser of in He is responsible for the procurement of hydraulic components. He has done an excellent job some time ago and has been praised by his supervisor for many times. Before the shopping season, he wanted to relax and planned to go on vacation with his family next week. A phone call from the owner disrupted all his plans. A major dealer in asked for help for a excavator produced by their company within 1 week . His engineer came to the user for routine maintenance and found that there was oil leakage in the hydraulic system. After pressure test, it was found that there was oil leakage in the hydraulic check valve, and 12 excavators had such faults. this hydraulic check valve, and got the reply that it was too cold in at this time. For such high frequency operation, even if the hydraulic check valve was replaced, it was estimated that the hydraulic check valve would still leak oil 1 week later. Unless more low temperature resistant sealing rings are used, this will take time to test, but the finishing time is to be determined. was so helpless, he had to find a new hydraulic valve supplier. asked several local hydraulic valve manufacturers. They either didn't have time to produce or require over 50pcs MOQ. After knowing these situations, the supervisor asked Daniel to give the dealer a plan that can be implemented within 10 days. had to cancel the vacation. thought of HYDRUALIC VALVE who he had contacted for inquiry before. He emailed us to ask whether we can produce the hydraulic check valve for the excavator, which needs to be resistant to low temperature. According to the drawings and working conditions provided by him, we advised that it takes 20 days to customize. All our existing hydraulic check valves are not close to this size. reiterated the hydraulic check valve needs to be low temperature resistant, and frankly told us what they are currently experiencing. I answered directly that the core lies in the low temperature resistant sealing ring. Daniel felt that maybe could solve this problem. After 18 days, we sent a sample of hydraulic check valve. The test results proved feeling. The parameters passed the test and there was no oil leakage at low temperature. The order for 12 hydraulic check valves was also easily confirmed. hanging heart can finally be put down. asked why hydraulic valve manufacturer needs time to be determined to test, and we solved it in 18 days. Why hydraulic valve manufacturer is unwilling to do this small quantities, but it is OK for hydraulic valve. At the same time, the price of hydraulic valve is cheaper than that made in and that made in the .

Whenever there is a new sample of AAK hydraulic valves, I must put it on the desk for a few days. Take a look at the hydraulic check valve with the same attitude of appreciating works of art, and taste a cup of coffee. The work is so simple. The parameters of AAK hydraulic check valves have surpassed most of the domestic hydraulic valve counterparts, and the appearance is also beyond what the 10-year-old hydraulic check valve manufacturers are able to keep pace with. AAK hydraulic valves have no quality complaints for 6 consecutive years. In 2019, AAK hydraulic check valves were used on aircraft by a Russian customer, which is a witness of good quality. AAK hydraulic check valve, how good is it? See the visual comparison in the picture below. Only from the appearance, the hydraulic check valve produced by 10 years old factory has lost. Not to mention meeting the parameters of hydraulic check valve using in aircraft, they may not dare to think or do it. AAK hydraulic valves is an ODM manufacturer for international first-line hydraulic valve brands. It is difficult to find the third one in Ningbo, the hometown of hydraulic valves. You can also have a small try. AAK HYDRAULIC VALVES (198) 2022-04-16

Last Friday, we received 3 emails from Niki, they are all the order for a same hydraulic check valve, but only the ship to address is different. It is the first time for their company to place the orders of 1,500 hydraulic check valves at one time. Niki is a purchaser of a Dutch hydraulic equipment company. Last year, a boarding bridge equipment needed hydraulic check valves. At that time, he planned to purchase from old suppliers. Unexpectedly, after dozens of hydraulic check valves from the initial samples were installed on the boarding bridge and tested for less than a month, the boarding bridge will slowly decline automatically. The engineer judged that the hydraulic system did not maintain the pressure, and it is likely that some hydraulic check valves leaked. However, after disassembling and inspecting the hydraulic check valves, it was found that the matching clearance accuracy of the valve spool and valve sleeve was within the normal range, and there was no jamming. Niki contacted the hydraulic check valve manufacturer, and manufacturer also didn't know why the hydraulic check valve leaked, so they could only replace those leaking hydraulic check valves. Niki is a little worried that if the leakage source of the hydraulic check valve is not found and replaced blindly, there may be a bigger problem later. Niki was not satisfied with the old supplier and had to start looking for new manufacturers of hydraulic check valves again. AAK received message from Niki on our website: what are the reasons for the leakage of hydraulic check valves? I realized that there was a leak in the hydraulic check valves purchased by Niki, but he hasn't found the root cause. After receiving the drawings of hydraulic check valve and the working conditions of boarding bridge equipment provided by Niki, we still can't 100% determine what caused the leakage of hydraulic check valve. We suggest him send us one of the previously leaked hydraulic check valves for analysis. After dismantling, our engineer is 90% sure to understand the root cause of the leakage, but still need to try sample to make it 100% sure. Niki is also willing to allow AAK to make samples according to his hydraulic check valve drawing. One month later, we sent 12 samples of hydraulic check valves to Niki and told him that the leakage of the hydraulic check valves from original manufacturer should be caused by poor details in production. There will be a certain gap between the cap and the thread of the valve sleeve of the hydraulic check valve. How to seal this gap is not only the detail but also the key, especially for the equipment with high working conditions. AAK uses thread anaerobic adhesive, which can completely fill the gap, enhance the sealing or retention force of mechanical connection components, prevent thread loosening and leakage due to vibration between the cap and valve sleeve of hydraulic check valves, and protect the joint from corrosion. Few hydraulic valve manufacturers

In March this year, the sales manager of Caterpillar received a phone call from a Spanish customer complaining that several excavators produced by their company had small start-up faults. The repairman judged that the hydraulic system leaked oil, which should be caused by the leakage of the hydraulic check valve. The customer asked them to replace the hydraulic check valve as soon as possible. This customer accounts for 40% of Caterpillar's sales. Although it has passed the maintenance period, they must help the customer solve the problem. The original hydraulic valve supplier said that for the hydraulic check valve under this working condition, there can only be no leakage for 2-12 months. In extreme cases, it may be less than 2 months. The customer was disappointed with such a maintenance plan. The owner asked Mark, the purchasing manager, to find a solution satisfying the customer. Mark contacted more than 10 hydraulic valve manufacturers, but did not get a satisfactory reply. He owner urged him to make a new plan twice a day. Mark thought of AAK HYDRAULIC VALVE he had contacted before. Maybe AAK can do some help. He firstly asked us why so many hydraulic valve manufacturers can't achieve 0 leakage for more than 12 months for this style of hydraulic check valve? The hydraulic check valves often use steel ball or metal cone slide valve to contact and compress with the orifice of metal valve seat under the action of spring and fluid pressure to prevent the reverse flow of liquid, but it is difficult to achieve absolute seamless butt joint in the cutting of metal contact surface. Especially under the special working condition of this customer, it is more difficult to avoid leakage. This hydraulic valve manufacturer who has insured for 2 months is already great. Mark thought that AAK HYDRAULIC VALVE could not produce a hydraulic check valve with 0 leakage for more than 1 year, and asked how long we could insure at most. AAK can produce hydraulic check valve with 0 leakage for more than 12 months. If there is no leakage within 1 month, and if subsequent maintenance is in place, the hydraulic check valve can be 0 leakage for 24 months. Mark was surprised at our reply and thought we were joking. Let's talk about it with facts: AAK will send the hydraulic check valve samples within 20 days, you test the hydraulic check valve first, and we will then discuss it after the test. After 15 days, AAK sent the hydraulic check valve samples to Caterpillar. Their engineers conducted internal test first, and there were no abnormalities in many tests. Their after-sales personnel took the samples directly to the customer's construction site for on-site installation and commissioning. It worked continuously for 12 hours, and everything was still normal.

When I got up to go to the bathroom at 1 a.m. last Monday, my wechat phone rang. It was from Carl, the purchasing manager of Denison hydraulic pump company in the United States. I was very surprised by this phone call. Generally, we communicate with Carl in the form of e-mail and have never used wechat phone. Carl firstly said sorry to disturb my rest, and asked if I could arrange a video conference at 8:00 tomorrow morning. He needs to discuss a troublesome problem with our technical team. I'm concerned that the communication on the phone will not be clear, and asked him to send me a written email first, and then I'll reply to him. Half an hour later, a detailed email with a schematic diagram of the hydraulic system came in. Last week, the hydraulic pump supplied by them encountered problems with his customer. The customer's hydraulic system has been shelved for half a year, and now it needs to be driven. After the operator starts the hydraulic pump, there is no pressure in the hydraulic system. The field engineer judged that there was no flow output of the hydraulic pump, but after inspection, it was found that the rotation direction of the motor was consistent with that of the hydraulic pump, and the oil level, oil temperature and viscosity of the hydraulic pump met the working conditions. The suction system of the hydraulic pump was replaced, including the oil suction pipe and filter. After startup, there was still no flow output. The transmission parts inside the hydraulic pump are intact without falling off, fracture and blade jamming. A week has passed and no reason has been found. Because the hydraulic pump is still in the warranty period, if it cannot be solved in another week, it can only be returned for claim. Carl asked the original supplier of each part for the hydraulic pump and got nothing. After reading the email, I asked him if the hydraulic pump used a hydraulic check valve? Carl said that the hydraulic check valve was provided by HAWE company in the United States, but the after-sales period of the hydraulic check valve has expired. Because AAK supplied hydraulic check valves to their company last year, and the quality was very satisfying, although the hydraulic check valve in this hydraulic pump is not from AAK, he wants to see if AAK technical team can find out the reason. I said there was no problem with the 8:00 video conference tomorrow, because the chief engineer of AAK didn't travel, but I'm not sure if we can help. The next day in the video conference, their engineers showed the whole system. Our chief engineer found that the displacement of the hydraulic pump was 8ml / R, so he asked them to fill the hydraulic pump directly in the oil outlet pipeline, and then start it up. The hydraulic pump still had no flow.

A tiny detail of the hydraulic check valve symbol direction is wrong, which put the hydraulic check valve manufacturer in a very difficult position, the factory is almost closed. There is a devil in the details. Whether you can grasp the devil of the hydraulic check valve symbol requires you to think every day, in addition to hydraulic check valve, hydraulic check valve, and still hydraulic check valve. When I opened the mailbox, I saw the e-mail of Adair who we had known for 3 years. There was a habit with Adair. He purchases only one type of hydraulic valves from each one hydraulic valve manufacturer. We AAK HYDRAULIC VALVE has been his supplier for the hydraulic pressure valves. After reading the email, it was actually a proofing request for a hydraulic check valve, not a hydraulic pressure valve. It was a little abnormal. I thought he sent the wrong email. I reminded him whether the e-mail was sent by mistake. He said bluntly that he would need 3 samples of the hydraulic check valve as soon as possible, according to the drawings in his email. Somehow, I always felt there was a problem somewhere, and I went to see the drawing of the hydraulic check valve. It is found that in the layout at the bottom of the drawing, the arrow direction on the hydraulic check valve symbol is reversed. For the hydraulic check valve symbol, the arrow direction is reversed, which is fatal. It seems that a designer is unlikely to make such a low-level mistake. When the technical team got the drawing and started proofing, they called me. The hydraulic check valve symbol on the drawing seemed wrong. I'm glad they can also find that there is an objection to the hydraulic check valve symbol. I asked what they think of the hydraulic check valve symbol. They suggested making two sets of samples, one according to the hydraulic check valve symbol on the customer's drawing, and the other is for the hydraulic check valve symbol we understand. When Adair received two sets of samples, he deliberately asked why they were two sets of samples. When we pointed out the details of the hydraulic check valve symbol, Adair began to tell me the devil's story of the hydraulic check valve symbol. 6 months ago, he sent his hydraulic valve manufacturer the drawing with this hydraulic check valve symbol, which was made by their chief designer overnight. The hydraulic valve manufacturer proofed according to this drawing. As a result, the hydraulic check valve sample was also approved at one time. The devil began to make trouble from this time. The 2,000 hydraulic check valves were produced and shipped to his customer. The customer is testing a new production line and needs to use these hydraulic check valves. After installation, there is a big problem in startup and commissioning. Because of the wrong direction, the medium returned, polluting the whole new production line, and directly causing a loss of more than 260,000 US dollars.

This morning, Robert sent an email asking about the production time of 1,200 hydraulic check valves, which surprised me a little, because in the past 2 years, he normally just placed small quantity trial orders of hydraulic check valves. Robert is a purchaser of John Finlay company in Australia. We met 2 years ago. A batch of hydraulic tamping machine equipment of their company began to receive complaints again and again from the previous year. After inspection, it was found that the hydraulic check valve in the equipment did not maintain pressure. Robert contacted the original hydraulic check valve manufacturer to find a solution. The manufacturer advised that the working pressure and working frequency of the hydraulic tamping machine may be too high, resulting in frequent collision between the ball valve and valve seat of the hydraulic check valve, affecting the sealing effect. The only solution is to replace the leaked hydraulic check valve. Although replacing the hydraulic check valve is a heavy workload, Robert has no choice but to accept. The trouble is that 6 months later, the same problem happened again. The customer was very unhappy. The boss asked Robert to find a new supplier of hydraulic check valve immediately. Robert suggested purchasing hydraulic check valves from AAK to replace those unqualified ones, because the durability test of AAK hydraulic check valves was the most lasting among all of the samples from different manufacturers at the beginning. At present, there is an equipment installed with AAK hydraulic check valve, which has been used for 1 year but without any abnormality. The boss thought that the price of AAK was more than 20% higher and unacceptable, and asked Robert to look for a new manufacturer of hydraulic check valves. In the process of continuous screening, Robert selected 5 hydraulic check valve manufacturers to try their samples. Basically, after half a year, these hydraulic check valve samples had similar problems one after another. Robert was at a loss. He once again suggested to the boss to purchase AAK hydraulic check valves. After comparing so many hydraulic check valve manufacturers, none of their samples can be used for more than 1 year under this working condition, but the equipment installed with AAK hydraulic check valve has been used for nearly 2 years, and there has been no failure to maintain pressure. If the hydraulic check valve needs to be replaced every 6 months, the after-sales cost is too high, which has far exceeded the 20% higher cost of the hydraulic check valves. More importantly, it brings the reputation of unstable equipment quality to users. After listening to Robert's analysis, the boss approved AAK as the preferred supplier of their company for hydraulic check valves. It took Robert 2 years to persuade his boss to place a large order with AAK. He knew that the durability of AAK hydraulic check valve

Last week, Eddy emailed me that after AAK hydraulic check valves of the test order has been used for 3 months , the O-ring seal was still free of wear. He was finally relieved. Eddy, who works at Terex company in the United States, has successfully purchased hydraulic valves from China over the years, and his owner is also very satisfied. At the beginning of last year, a customer complained about the hydraulic equipment supplied by their company for offshore oil field exploitation, which made him very passive. Some equipment has the phenomenon that the drilling machine rises slowly or cannot rise. Their engineer found that the hydraulic check valves used in the oil circuit of the hydraulic equipment had internal leakage, the one-way oil circuit could not be fully locked, resulting in the inability of the equipment to rise. Their engineer can only replace the hydraulic check valves with the previous spare ones and bring the problematic hydraulic check valves back to the company. Eddy sent these hydraulic check valves to the original supplier. The supplier replied that the reason for the leakage in the hydraulic check valves was that the ambient temperature was too low. The O-ring seal of the hydraulic check valves was hardened and worn quickly in extremely cold conditions, which was difficult to solve. Eddy knows that if he can't give reply to customer like this, he must find a manufacturer who is able to produce the hydraulic check valves working at low temperature. Eddy contacted several hydraulic check valve manufacturers, most of them reported that it was difficult to achieve 100% leakage free under such extremely cold conditions. Eddy was worried. When Eddy contacted us, our engineer wanted to see the real reason for the wear of the O-ring of his hydraulic check valves and asked him to send the defective hydraulic check valves. After receiving the samples, our engineer realized that even if the cold resistant O-ring is used, it may not be 100% leak free, and the structure of the sealing ring needs to be changed, because the internal structure of this hydraulic check valve is a little complex. Eddy said that this is the only different reply he received. It seems that Eddy still doesn't believe that AAK can solve the leakage problem of the hydraulic check valves. I told him that a Russian customer has purchased hydraulic relief valves from us, and their hydraulic equipment is also used in oil fields. The customer told us that under extremely cold conditions, the service life of AAK hydraulic relief valve is more than 4 times that of its peers. Three weeks later, we sent 4 pieces of hydraulic check valves of the test order to Eddy. There was no news after 3 months. Until last week, we received email from Eddy amazing that their engineers also admired our idea of adding retaining ring to the O-ring of the hydraulic check valves.

Hydraulic check valve with 12 shipments in 1 year, 3 key elements benchmarking SUN CXFA This week, we launched a hydraulic check valve with 3 key elements benchmark SUN CXFA standard parts. This hydraulic check valve is free-flow, nose-to-side check valves are on/off circuit components that allow free flow from the inlet (port 1) to the outlet (port 2) and block flow in the opposite direction. The manufacturing quality of this hydraulic check valve is compared to SUN CXFA; the function of this hydraulic check valve is benchmarking against SUN CXFA; the performance of this hydraulic check valve is benchmarking against SUN CXFA. In 2022, AAK shipped this hydraulic check valve 12 times to 4 customers, and received 4 inquiries within 4 months of 2023. AAK hydraulic check valve 2 major advantages: 1. Low leakage, internal leakage 1 drop/min. 2. 3 key elements benchmark SUN, but the price is less than 70% of SUN. Technical parameters of AAK E-CXFA Hydraulic Check Valve: Maximum Operating Pressure: 350 bar (5000 psi) Capacity: 40 gpm (160L/min) Internal Leakage: 1 drops/min. Cavity: T-5A AAK hydraulic check valve, 3 key elements benchmark SUN CXFA, you can also have a small try. AAK HYDRAULIC VALVES (564) 2023-04-17

At 05:10 this morning, I was listening to music and browsing emails. Billy, who had no news in 9 months, sent an email. Without reading the email, I could guess that the hydraulic check valve developed by AAK for 3 months last year had a result. Opening Billy's e-mail and it is an annual order of 5,000 hydraulic check valves at one time, with about 500 hydraulic check valves delivered every month. Billy is from a hydraulic equipment company in the United States, he has purchased a small number of high-pressure resistant hydraulic check valves from AAK in the past. At the beginning of last year, his company received complaints from a customer that its high-power bulldozers were prone to weak starting of the hydraulic system after being used in less than half a year. The after-sales engineer found that the hydraulic check valves leaked and can not maintain the pressure and caused the problem. Billy contacted the original manufacturer of the hydraulic check valves, and manufacturer advised that the system pressure of the high-power bulldozer exceeded 450bar, and the opening and closing frequency was also high. When the hydraulic check valve was in the high-pressure state above 450bar, the valve spool was worn quickly, and the service life could only be guaranteed as 1 million times. Therefore, it was normal to replace the hydraulic check valves every half a year. If you want a hydraulic check valve with a service life of 2 million times, you can only purchase it from German HAWE. Billy has no choice but to make do with the hydraulic check valves of the original manufacturer first, but the after-sales cost every half a year is really unbearable. Maybe other manufacturers can offer hydraulic check valves with service life more than 1 million times. Billy began to contact other factories, including AAK. After receiving Billy's email, AAK engineers had reached a conclusion according to the hydraulic check valve drawings and bulldozer working parameters. In order to exceed the service life of 2 million times of the hydraulic check valves, we can only test new high-pressure resistant materials. We replied Billy at that time that according to the existing steel options of AAK, what your original manufacturer said was right, it can only guarantee the service life of 1 million times of the hydraulic check valves. However, we are confident to develop the one of 2 million times, because we have our own R & D experience in anti-high pressure. Billy replied directly that AAK would be given 3 months to sample the hydraulic check valves with pressure resistance above 450 bar. He also frankly informed that two other hydraulic check valve manufacturers were also making samples. If all manufacturers fail, they can only buy high-pressure hydraulic check valves from German HAWE. Three months later, AAK successfully sent 20 hydraulic check valve samples to Billy. Nine months later, the email came from Billy today.

Cuenca is a senior purchaser of AGRIA company in Spain. The boss is very satisfied with his purchasing work. Two years ago, AGRIA company developed a hydraulic equipment, and there were complaints after sales for more than half a year. The main problem was that the starting force of the hydraulic system would be insufficient, which was caused by the increase of internal leakage of the hydraulic check valves in the equipment. After Cuenca contacted the original hydraulic check valve manufacturer, the manufacturer said that some hydraulic check valves may have deviation during assembly, and he was willing to replace the hydraulic check valves with large leakage with new ones. Cuenca thought it was completely solved after replacement, but what surprised him was that less than a year after the new hydraulic check valve was replaced, the same problem occurred again. The boss was very disappointed with his purchase of hydraulic check valves this time. The manufacturer of the original hydraulic check valves still said that except for replacing the hydraulic check valves, there is no other way. Cuenca began to worry that if the same problem happened a third time, it would be too shameless. To be safe, he began to look for a new supplier of hydraulic check valves and began to test samples. At the same time, he also wanted to know why the hydraulic check valves produced by the original manufacturer leaked. In this way, Cuenca contacted AAK hydraulic valve. After several rounds of communication with Cuenca, we learned the story between him and the original manufacturer of hydraulic check valves, and suggested him to send us the hydraulic check valves with problem and provide us the drawings of hydraulic check valves at the same time. AAK engineer disassembled the hydraulic check valves of the original manufacturer and found that there were wear marks on the sealing line on the surface of the poppet valve. When the pressure oil reversely enters the hydraulic check valve, the cone cannot strictly seal the oil and cause leakage, and some oil flows out of the oil inlet. After receiving AAK's analysis, Cuenca asked us to make 4 samples of hydraulic check valves according to his drawings. Our engineers designed a new hydraulic check valve according to the service frequency and working conditions of the equipment, replacing the cone valve with the ball valve. The cone valve is prone to fatigue creep deformation and wear after working for a long time, resulting in a gap between the valve sleeve and the cone, resulting in leakage. The outer circle of the ball valve can contact the inner taper ring line, and the connecting hole can be closed to reduce the leakage caused by wear. Cuenca was surprised that AAK dared to take the initiative to modify the drawings of their hydraulic check valves, and expected to see the sample performance of AAK hydraulic check valves. Two months later, AAK sent samples of the newly designed hydraulic check valves.

In the Spring Festival, I received a confirmed price for a large quantity of hydraulic check valves from Stephen. The contact between Stephen and I is only 2-3 times in the whole last year. It was noted at the end of the email that he needs me to contact him as soon as possible to discuss this hydraulic check valve. Stephen comes from American CASE company. We met the year before last. After communication, it was learned that at the beginning of last year, a bulldozer of their company needed to use hydraulic check valve, the one that AAK had made samples at the beginning. Because the price of AAK hydraulic check valve was 20% higher than that of his original supplier, Stephen did not choose to purchase hydraulic check valve from AAK. Some time ago, the customer complained that the hydraulic pump was damaged due to the sudden increase of hydraulic system pressure. Stephen communicated with the original hydraulic check valve manufacturer and the manufacturer replaced the hydraulic check valve with a new one, but 3 months later, the same problem came again. The customer was very dissatisfied that this delayed the construction and needed the problem solved at one time. Stephen went back to AAK and asked about the price of the hydraulic check valve. He needed us to maintain the quotation offered last year. I asked Stephen why he went back to AAK to purchase the hydraulic check valve. He told that since the first complaint from the customer, their engineers retested the original hydraulic check valve samples. The hardness of AAK sample was the highest, and the material hardness of each part of the hydraulic check valve was no less than HRC65. I know why their hydraulic check valve went on strike in 3 months. When we made the sample, we knew that the working pressure was more than 450bar, which was a challenge for the hydraulic check valve. The material hardness of each part of the hydraulic check valve is required to reach more than HRC65. There may be no more than 5 hydraulic valve manufacturers that can reach this level in Ningbo. Stephen wondered why the material hardness of each part of AAK hydraulic check valve can be over HRC65? 1. Material selection is the core. AAK adopts 20CrNi2MoV high carburizing bearing steel imported from Germany for this hydraulic check valve. 2. Heat treatment is the key. Through secondary quenching + cryogenic treatment + low-temperature tempering process, it is cooled to 650 ~ 700 and put into the furnace. After cooling to 450 ~ 500 , it is discharged from the furnace. The micro hardness is 237 ~ 247 HV. 3. In the later stage, point-to-point testing is the key. SonoDur3, a Rockwell hardness tester imported from Germany, adopts the UCI hardness test method, and the test program is fast and mobile to carry out nondestructive testing on the hardness of each component of the hydraulic check valve efficiently and accurately.

Duden is from Lukas hydraulic equipment company in Germany. We have cooperated for more than 2 years on hydraulic check valves and hydraulic throttle valves. The order volume is small each time, but the parameter requirements are very high. AAK never despised it because of the small order quantity of the hydraulic check valves or hydraulic throttle valves. At the end of last year, their company developed a new hydraulic unit. Due to time constraints, Duden purchased hydraulic check valves and hydraulic throttle valves from local hydraulic valve manufacturers in Germany. The technicians found the original design defects after installing the integrated valve into the equipment. The position of the hydraulic throttle valve next to the hydraulic check valve is high, accounting for a little position of the motor, which makes it difficult to install the motor. Lukas engineers are a little depressed. If the position of the hydraulic throttle valve is changed, the whole oil circuit layout needs to be changed, but the power supply of the hydraulic system will be affected after changing the oil circuit. What is more troublesome is that there is not much time to redesign and proofing. The Engineers asked Duden to contact some local hydraulic valve manufacturers to check if the design size of the hydraulic throttle valve could be slightly adjusted so that the motor could be installed. Duden checked with several local hydraulic valve manufacturers, all of them were not willing to make samples because of small quantity of the hydraulic throttle valves. Duden tried to purchase small-size hydraulic throttle valves from China to solve the installation problem of the motor. Some Chinese hydraulic valve manufacturers said that they could make samples according to the requested size of their hydraulic throttle valves, but the time needed was more than 30 days. Duden couldn't accept this time and was more worried about the quality of hydraulic throttle valves from these factories. Duden sent an email to AAK asking if we could make several samples of hydraulic throttle valves in 5 days. In the past, the sample time gave by Duden was usually flexible with more than 2 weeks. After asking, I learned that their designers are facing embarrassment. It is also too tight for us to make several hydraulic throttle valves in only 5 days. I suggest Duden give us the overall layout of the integrated valve block. Maybe our engineer has a solution. According to the hydraulic schematic diagram provided by Duden and the specific use of the hydraulic integrated valve block, AAK engineers analyzed it step by step. Finally, it was found that if the hydraulic throttle valve and the hydraulic check valve were designed in parallel, the functions of the two valves were combined to form a hydraulic throttle check valve, which was installed at the position of the hydraulic check valve, and the installation hole of the hydraulic

Shandong Senteke Hydraulic Co.,Ltd.We are manufacturer of cartridge valve and hydraulic system.And we can design valves according to your requirements