Oil window: The oil viewing window located on the side of the water pump iseasy to inspect and the oil level is easy to repair. High and low pressure water seal components The high and low pressure dual water seal design of the"U" type "Buna N" material enhances the performance of thewater pump and improves its service life. The plunger support guide ringensures the coaxiality of the plunger, extending the service life of the waterseal and plunger. Pump head assembly: Selected forged brass material, high strength, no porositydefects, long service life, high pressure resistance, stable operation,reinforced 6-bolt fastening, 10mm, grade 8.8. Check valve assembly: The valve cage is made of specialmaterials that are sturdy and durable. The stainless steel 303 and 404 poppetvalves and springs, as well as the brass valve seat and cover, are sturdy anddurable, extending their service life. Pommel Precision machined hard solid ceramic plunger, sturdy anddurable. Crank Axle Accurate rounded corners and process treatment ensure durabilityand service life. Oil seal and O-ring A better crankcase oil sealing system, with stainless steelsprings for oil seals and O-ring seals to ensure sufficient tension. Bearing The positioning of large-sized bearings and snap rings ensuresthe concentricity of the crankshaft connecting rod, ensuring stable operationof the water pump. Bearing Block Precision machining ensures coaxiality and concentricity. Plunger Connecting Rod The high-quality alloy connecting rod has high load strength,durability, and stable operation. Crankcase The surface of the crankcase that has been oxidized by precisioncasting is a classic streamline design.
Technical: Suitable for 20L drums Max. Delivery: 5L/min Features: Force feed high volume pumps Extreme viscous grease Reduce waste Clean and convenient method of drum change Our pumps take on the toughest challenges from transferring lighter fluids(oils, solvents and adhensives)to moving medium-viscosity materials(RTV silicone, greases, coatings, plastisols and offset inks) to pumping very heavy viscosity materials(ink flushes, epoxies and mastics). Positive-priming force on the material: Downward force of the follower forces material into the pump inlet, assuring positive priming of high-viscosity materials Follower Has an elastomer seal: Twin blade wiper seals against the material container's sides, preventing drying and contamination of the material and wipes the container's sides clean Four-way air valve control: This directional valve controls Up/down movement of the follower. Primer unit remains coupled to the air system at all times(use of an air regulator and gauge is recommended).
Pumps,Water pumps
700bar Hydraulic pump for hydraulic puncher.
We are one of the concrete pump manufacturers in Korea Brand: SAMIL GIANT in Korea Boom length: 67m 62m 58m 52m 48m 45m 42m 37m 32m 28m 24m 21m Stationary pump, Line pump We are able to send full details if you make an inquiry
Pumps
Chart recorders Gas analysing meters & detectors Load cells & display units. Instrumentation: flow, level & pressure control equipment for all industrial processes & mediums Vacuum switches generators & pumps Pressure gauges
Sewage Pump
We Supply Wide Variety Of Pumps To Our Valued Customer All Over The World. Our Customers Manly From Power, Steel, Sugar, Paper, And Chemical Industries. Few Types Of Pumps Are Listed Below. Please Refer Our Brands Section For Checking Out Our Pump Brands End Suction Pumps Split Case Pumps Multi Stage Pumps Sump Pumps Vacuum Pump Submersible Pumps
double tube hand pump for BIG SUP board TRIPLE ACTION it's more compact and light. It's the best for brands who want to use a pump of triple action as standard equipment in their SUP. The compact piston permits also females and young guys to be able to achieve easily high pressure. HP6, being used in TRIPLE-doublesingle action, can achieve 30psi rapidly and effortlessly. The switching 3-2-1 can be realized easily and comfortably rotating the switch knob. Itâ??s completely customizable for colour, graphic and calibration of gauge meter. Features: · capacity 3.2+3.2L, max. pressure 30psi as DIN EN 16051 · switch knob to change comfortably from triple to double or single seals and anti-sand filter for long life of pump and SUP extra long body and high-airflow piston for an easier inflation pump completely shock-proof, compact and light (1.7kg) · shockproof gauge meter
Salient Features Highly efficient 3-Phase Water Filled Motor - 100% EC grade copper winding - Easily Rewindable - Motor Designed with Higher Cooling Effect Ensures Longer Life - Sustainable uniform performance for years - Ensures long life durability - Optimized Hydraulic & Mechanical Design - Improved efficient performance - Excellent output in Low Radiation - Dynamically balanced design - Zero maintenance Product Specification Power Range : 3.0 HP to 10.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 â?? 50 Hz Input Solar DC Power Range : 3000 Wp, 10000 Wp Input Solar DC Voltage Range : 330 Vmp , 600 Vmp Head Range : 10 Mtr , 50 Mtr Discharge Range : 126000 LPD , 425000 LPD Type of Duty : S1 Material Of Construction Part Grade Oil Seal : Nitrile butyl rubber Motor Shaft : SS - 420 Motor Body : Cast Iron / J4 Motor Bush : LTB-4 / Teflon Thrust bearing assembly : SS - 420 & Carbon Base : Cast Iron Bracket : Cast Iron Flange : Cast Iron Casing : Cast Iron Impeller : Cast Iron
Highly efficient 3-phase Air Cooled motor - 100% EC grade copper winding - Easily Rewindable - Good suction lift characteristics - Sustainable uniform performance for years - Ensures long life durability - Optimized Hydraulic & Mechanical Design - Improved efficient performance - Excellent output in Low Radiation - Dynamically balanced design - Double shielded ball bearings, so no need of external lubrication - Mechanical seal or stuffing box is provided as per customers requirement - Zero maintenance Product Specification Power Range : 1.0 HP to 10.0 HP Operating Speed : 0 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 10000 Wp Input Solar DC Voltage Range : 110 Vmp, 600 Vmp Head Range : 10 Mtr, 50 Mtr Discharge Range : 45000 LPD - 405000 LPD Max. Suction Head : 7 Mtr Type of Duty : S1 Material Of Construction Part Grade Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Water Pump suitable for Commercial vehicles,Cars
Sewage Pump - B
Inline Pressure Pump
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
Product Specification Power Range : 1.0 HP to 2.0 HP Operating Speed : 0 - 3100 RPM DC Power Range : 900 Wp - 2000 Wp DC Voltage Range : 70 Vmp - 110 Vmp Head Range : 30 Mtr - 90 Mtr Discharge Range : 8000 LPD - 30000 LPD Type of Duty : S1 - Zero Running Cost - Less Maintenance - Eco-Friendly - Simple Installation - Pollution Free Material Of Construction - Motor Part Grade Mechanical Seal : Graphite Ceramic Motor Shaft : Stainless Steel Motor Body Pipe : SS-304 Lower Hosing : Aluminum Diaphragm : High Nitrile butyl rubber Top Cap : Stainless Steel Bottom Plate : Stainless Steel End Cap : Stainless Steel MATERIAL OF CONSTRUCTION SCREW (HELICAL) PUMP Part Grade Outlet : SS-304 Suction : SS-304 Outer Shell : SS-304 Rotor Screw : Stainless Steel Stator : Rubber Coated Alloy MATERIAL OF CONSTRUCTION â?? CENTRIFUGAL PUMP Part Grade Check valve housing : SS-304 Check valve : PC Suction : SS-304 Outer Shell : SS-304 Impeller : POM Bowl : PC Pump Bush : NBR Pump Sleeve : Stainless Steel Pump Shaft : Stainless Steel Coupling / Pump Couple : Stainless Steel
Salient Features Highly efficient 3-phase water filled motor - Easily rewindable - Dynamically balanced design - Extended life with flawless performance - Thrust bearing : Carbon + S.S. material for High thrust load capacity - 100% EC grade copper winding - Presenting world 1st design (design registered 100% fully S.S.-304 investment casting pumps. - Zero maintenance - Superior performance - Sand proof operation - Highly efficient 3-phase water filled motor Product Specification Power Range : 1.0 HP to 20.0 HP Operating Speed : 0 - 2890 RPM Operating Frequency : 0 - 50 Hz Input Solar DC Power Range : 900 Wp, 20000 Wp Input Solar DC Voltage Range : 110 Vmp - 600 Vmp Head Range : 30 Mtr , 220 Mtr Discharge Range : 10000 LPD - 420000 LPD Type of Duty : S1 material of construction - motor Part Grade Body Lock : Spring Steel Stud Ring : M.S. (Zinc Coated) Stator Stamping : CRNGO - M45 Silicon Winding Wire : 100% EC Copper Shaft : SS-420 Rotor Stamping : CRNGO - M45 Silicon Copper Lamination : 100% EC Copper Upper Housing : SS-304 Lower Housing : SS-304 Connection Piece : SS-304 Oil Seal : NBR TB Set : Carbon + SS Base : SS-304 Drain Plug : Brass Couple Sleeve : Stainless Steel Water Bolt : Brass MATERIAL OF CONSTRUCTION PUMP Part Grade Suction : SS-304 Couple : Stainless Steel Couple Counter : SS-304 Rubber Seal : NBR Bush Seal Cover : SS-304 Bowl : SS-304 Impeller : SS-304 Key : SS-410 Bowl Bush : NBR Bush : LTB-4 Middle : SS-304 Cap : NBR Outlet : SS-304
