Huahao frp round solid rods are widely used as pcb equipment drive shafts .Pcb equipment fiberglass rod has many advantages : good corrosion resistance , lightweight and high strength , heat insulation and non-poisonous , smooth and good looking surface, small friction resistance high transport capacity , easy installation , long service life . This product is suitable for pcb equipment and cleaning equipment. Colors: our regular colors include black , gray , red , orange , yellow , white , green , and blue . And we can offer any color you request . Customized colors are accepted . Welcome to visit our website . Dimension: 2mm to 100mm .
Industries Served Applied in various sports equipment. We offer custom-made parts. Functions and Characteristics 1.Light weight, high strength. The specific weight of FRP pultrusion fiberglass tube is 1.8-2.1g/cm, only 1/4 of steel. It is easy to transport and install. Compared with plastic, the strength is ten times of plastic products. 2.Corrosion-resistance, anti-aging and with a long service life. It can be used in different corrosive environment, such as acid, alkali, salt, some organic solvent and so on. In the areas of corrosion-resistance, it has the superiority that other metals can not compared with. Adding to the characteristics of good resistance to water and aging, its service life could be expected to more than 15 years. 3.Good security. FRP pultrusion fiberglass tube has excellent electrical insulation, non-magnetic, no spark and can also be add the process of flameproof according to users needs. 4.Good resistance to impact and can be designed freely. Better resistance to impact and fatigue make carbon fiber composite products can be bended repeated without permanent deformation. Otherwise, it can be designed into different sections according to the customers demand. 5.Colourful and Economics. FRP pultrusion fiberglass tubes have various specifications and the colors can be designed according to customers requirements. In addition, the price is affordable and have a good future.
Insulator core rod made of ECR fiberglass reinforced the epoxy resin.Insulator core rods also are also called fiberglass rod,FRP rod,GRP rod,fiberglass bar,Insulation rod,fiberglass stick ,ECR rod and so on. 1.Standard: IEC61109 2.Material: E glass and epoxy resin. 3.Process: Continuous pultrusion. For more detail,
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scra tch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Material: FRP Brand: HongBang Application: fishing rod, road mark, parking marke.
Material: FRP Brand: HongBang Application: fishing rod, road mark, parking marke.
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
k onto reel with easy pushi or pull of rod. 6. Duct rods/duct rodders have many applications, not only pulling the cable but also pulling 7. Anticorrosion , good elasticity , long working life. Fiberglass push pull, tracing duct rods, duct rodder--bazhou deli power tools Box
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod ma
Introduction Our company produces duct rodders has 12 years of history, we generate different diameter of duct rodders, diameter range from 3mm to 15mm length of 15mm.Duct rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of duct rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Wanqi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Electrical insulation FR4 G10 epoxy resin fiberglass rod is made from glass cloth fabric impregnated with epoxy resin, then heated into prepreg and rolling into the rod shape, finally put into the different diameters molds, under high temperature and pressure to cure into the rigid laminated rods. Usually for mechanical & electrical applications, with good moisture resistance. Diameter 6-110mm Length 1,000mm Color green/natural
Insulating Solid Rod is made of ECR glass reinforced epoxy resin.We use continuous pultrusion procss .The products fullfill The standard of IEC61109.Insulator core rods also are also called fiberglass rod,FRP rod,GRP rod,fiberglass bar,Insulation rod,fiberglass stick and so on. 1. Standard: IEC61109 2. Material: E glass and epoxy resin. 3. Process: Continuous pultrusion. Process: 1 - Continuous roll of reinforced fibers/woven fiber mat 2 - Tension roller 3 - Resin Impregnator 4 - Resin soaked fiber 5 - Die and heat source 6 - Pull mechanism 7 - Finished hardened fiber reinforced polymer Specifications: 1.Color: light green or brown. 2.Length: according to Customer requirement. 3. We offer customized products,including the new size, New surface treatment, Jointing the fitting, screw or mechanical.
Features and benefits: Strong non-conductive fiberglass rod construction. Rustproof bull-nose pulling eye. For longer conduit runs and underground duct. Rugged tubular steel reel with adjustable positioning. Feed device allows rod to feed out or be wound back onto reel with easy push or pull of rod. Many applications, both commercial and residential. 8pics 300kg 1350*480*1500.
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod WanQi rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage.
Introduction Our company produces Duct Rodders has 12 years of history, we generate different diameter of Duct Rodders, diameter range from 3mm to 15mm length of 15mm.Duct Rodders, 60m, 100m, 150m, 180m and a variety of specifications, of course also can according to the customer need to customize the length. The color of the rod is divided into white, yellow, orange, blue, black, green, red, we on the rod make m the number of markers, and can be used for the customers in the rod marker customers trademarks. We can provide a variety of Duct Rodders cage style, in order to meet the needs of customers in different countries. Product introduction The rod Deli rods are manufactured from state-of-the-art materials formulated to offer the high performance & durability demanded by our customers.The core of the rod is manufactured by the pultrusion process. This involves impregnating high strength continuous glass fiber filaments with a liquefied resin. The fibers are drawn in to a heated die where the resin matrix is cured, bonding the fibers together and allowing mechanical loads to be transmitted through the matrix and distributed amongst the fibers.The resulting pultruded rod combines both the high stiffness required to push the rod through long distances of ducting, with the flexibility to handle tight bends without damage. This inner core is then coated with a highly durable, scratch resistant polypropylene sheath which protects the core from mechanical damage. 1+2 4?? 1+2 4?? The frames Frames are also a feature of the Hunter systems. a larger footprint for stability; steel brake handles that will last forever; dual rod out-feeding positions and wheels inside the frame width. The two smallest sizes feature frames with the feedout built into the handle. All frames can be laid down on either side. These are just some of the design features that will make every unit more usable and friendly for the end user. Rod selectIon Which is the right rod diameter for any given application? The rod selection is usually governed by several factors including: The size of ducting it is to be pushed through The distance the rod is to be pushed The number and tightness of bends in the ducting If the ducting is already occupied by cable When being pushed through the duct, any rod will tend to form “sine waves”, hitting the wall of the duct at certain intervals. Each time the rod comes in contact with the wall of the duct, it causes friction. The friction will build and eventually prevent the rod from being pushed any further. Small rod in large duct will make more frequent contact with the ducting; the same rod in smaller duct will make less frequent contact and therefore less friction so it can be pushed further. Large rod in small ducting is a good situation, but reduced flexibility of the rod may cause increased friction in the tighter bends.
Raw Materials: Fiberglass Solid Epoxy resin Diameter: 12mm, 16mm, 18mm, 20mm, 26mm , 30mm, 36mm, 40mm, 45mm, 60mm, 80mm, 110mm . Length: as per the customer's request Application: For Electric Industry
Various solid fiberglass rods and bars designed as ribs and weight rods for roman curtains and shades Bundle
Fiberglass fishing rod Packing:slide fastener Length:2.7m-8.0m Material:fiberglass 100% Hollow. (please contact us for detailed information) Please send e-mail to us for the information .