NEOFLON ETFE is a copolymer of tetrafluoroethylene and ethylene, and has the lowest specific gravity among all fluoropolymers. It has superior characteristics in melt processability and mechanical properties compared with PTFE and FEP, and has good electrical and chemical properties. It is suitable for applications requiring its mechanical toughness, chemical resistance, heat resistance and electrical properties.
NEOFLON ETFE EP-506 is a resin for extrusion of thin coatingsof small wire sizessuch as aerospace wire, automotive wire, appliance wire, thin film and tubing, etc.. Itmay be used for injection molding of thin wall parts. Ethylene tetrafluoroethylene copolymer is a kind of chemical substance. ETFE is the strongest and toughest fluoroplastic. It not only maintains the good heat resistance, chemical resistance and electrical insulation properties of PTFE, but also greatly improves the radiation resistance and mechanical properties. The tensile strength can reach 50MPa, which is nearly twice that of polytetrafluoroethylene.
NEOFLON ETFE EP-506 is a resin for extrusion of thin coatingsof small wire sizessuch as aerospace wire, automotive wire, appliance wire, thin film and tubing, etc.. Itmay be used for injection molding of thin wall parts. Ethylene tetrafluoroethylene copolymer is a kind of chemical substance. ETFE is the strongest and toughest fluoroplastic. It not only maintains the good heat resistance, chemical resistance and electrical insulation properties of PTFE, but also greatly improves the radiation resistance and mechanical properties. The tensile strength can reach 50MPa, which is nearly twice that of polytetrafluoroethylene.
NEOFLON PFA AP-Series NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom. It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins.
NEOFLON PFA AP-210 is excellent in melt flowability and is suitable for injection molding and extrusion molding. Introduction - AP-210 is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether. - Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by injection molding and extrusion molding. - Excellent chemical resistance which is not affected by most of the chemicals. - Excellent heat resistance. Continuous use temperature is 260 â??. - It retains flexibility without losing toughness under the environment from cryogenic to high temperature. - Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency. - It shows high electrical resistance and dielectric strength. - Nonflammable like POLYFLON PTFE and NEOFLON FEP. - Excellent weather resistance. No properties change even when exposed outside for a long time. - Non-stickiness. It shows excellent releasability and water repellency / oil repellency.
NEOFLON PFA AP-Series NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom. It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins.
NEOFLON FEP NP-Series NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene. FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON PFA AP-Series NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom. It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins. Grades and Features of AP-Series Grades MFR (g/10 min.) Features AP-201 20 - 30 Superior in melt flowability. Suitable for injection-molded articles that have complex shape, and for ultrafine thin-wire coating (AWG34 - 44). AP-202 65 - 80 Excellent melt flowability. Suitable for injection-molded articles that have complex shape, and for thin-wire coating (AWG44 - 52). AP-210 10 - 17 Good melt flowability. Suitable for injection molding. AP-230 1.5 - 2.5 Superior in stress crack resistance. Suitable for extrusion and transfer molding. AP-201SH 20 - 30 High purity grade. Superior in melt flowability. Suitable for complex shape articles. AP-211SH 10 - 17 High purity grade. Long-term flexibility and good stress crack resistance. Suitable for joints and parts for pumps. AP-215SH 10 - 17 High purity grade. Suitable for injection molding. Suitable for joints and parts for pumps. AP-231SH 1.5 - 2.5 High purity grade. Long-term flexibility and good stress crack resistance. Suitable for extrusion and transfer molding. AP-210AS 11 - 14 Anti-static grade. Suitable for injection molding. AP-230AS 1.5 - 3.0 Anti-static grade. Suitable for extrusion molding. AP-230ASL 1.0 - 2.5 Anti-static grade. Suitable for extrusion molding.
NEOFLON PFA AP-Series NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom. It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins.
NEOFLON FEP NP-Series NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene. FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON FEP NP-Series NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene. FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene. FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON FEP NP-Series NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene. FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA. Grades and Features of NP-Series Grades MFR (g/10 min.) Features NP-20 4.5 - 8.5 Suitable for general extrusion molding of wire coating, pipes, tubes and films. NP-30 2.0 - 3.5 Suitable for thick-walled wire coating and wire jacket. NP-101 21 - 27 Improved melt flowability. Best suited for high-speed wire coating such as LAN cable. NP-120 4 - 10 Stress crack resistance is improved from NP-20. Wide range of applications, from thin-walled to thick-walled wire coating. We can give discount according to order quantity.
NEOFLON FEP NP-Series NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene. FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA. Grades and Features of NP-Series Grades MFR (g/10 min.) Features NP-20 4.5 - 8.5 Suitable for general extrusion molding of wire coating, pipes, tubes and films. NP-30 2.0 - 3.5 Suitable for thick-walled wire coating and wire jacket. NP-101 21 - 27 Improved melt flowability. Best suited for high-speed wire coating such as LAN cable. NP-120 4 - 10 Stress crack resistance is improved from NP-20. Wide range of applications, from thin-walled to thick-walled wire coating. We can give discount according to order quantity.
We are factory supplier of all types of plastic raw materials like ABS, EPS, HDPE, LDPE, LLDPE, PA, PET, PLASTIC MASTERBATCHES, PLASTIC RAW MATERIALS, POM, PP, PPO, PS, PTFE, PVC, PVDF. Aluminium and copper for wholesale buyer. Kindly please contact us for any inquiry about scraps, we are leading supplier. Filler masterbatch CACO3, Color masterbatch Factory Sales, Plastic Companies supplier, Quality colorful plastic masterbatch, Thermochromic Plastic, Fibreglass reinforced plastic, Pet granules suppliers, Black masterbatch CACO3 Filler, PA66 factory for sale, Clarian PVC pipe wax, plastic insulator materials, Plastic polythene injection, is polypropolene, CACO3 filler masterbatch, Quality PVC granules,HDPE Granule, Proporlene plastic virgin, Granules film grade, PP Recycled pelltes mask, idpe recycled granules, pvc regrind scrap, pla bio degradable, Plastic pets granule. IDPE recycling quality film grade, scrap prices pvc window, etfe powder, pet bottle flakes, PA66 recycled pellet, poly lactic acid, injection molding pla, scrap yard pc, recycled hips regrind, pvc resin paste, fluorosplastic, abs plastic scrap. Flake plastic scrap low rate, pp filler black master batch, regidity pom impeler ppo, plastic high temperature heat, price of scrap aluminium, lead prices per pounds, scrap price of steel, scrap price of brass, how much does plastic cost, price of scrap aluminium. Worldwide with a very good range of prices.The plastic recycling companies are playing the most appreciable job in preventing the environment from getting polluted by using plastic scrap in the process of recycling and make it reusable. PRM limited is one of the most popular companies that explored a huge appreciation for providing a great efficiency and effective plastic recycling process.
PVC cable and teflon, EP, PFA, ETFE, XLPE, TPU, Carbon fibre high temperature wire.
