CS-613W is 2-component water-based premium epoxy product. CS-613W as admixtures can improve the properties, particularly in relation to water absorption reduction, toughness enhancement, vibration damping and increase of the bond strength of cement to reinforcements other than being used as admixtures, CS-613W is used partial replacement of fine aggregate, for coating, sealing and repairing concrete and for coating steel reinforcing bars for corrosion protection. AREA OF APPLICATIONS Repair mortar for concrete areas. Industrial flooring. Bonding agent for new to old concrete. As water based primer. Can be applied with damp surface. FEATURE Weatherproof and waterproof of capabilities that help prevent the deterioration of the ground-coat material. Low odor. Washable with water including tools. Best to wash as soon as possible before it hardens.100% water resistant when cured.
1.We use imported base paper from Germany. For solid color, base paper most 80 to 120GSM. For wood base paper is between 70-85 gsm 2. High quality water-base ink- Available over 200 shades in Solid colors and wood grains 3. With clear texture ,high Fidelity meeting international standards. 4. With smooth surface coating 5. Germproof, mould proof, antistatic and wear-resistance. 6. Green environmental protection and Odorlessness which Conforms to the GB18584-2001 standard requirement 7. Can be used for the hot press molding craft, the production efficiency is high. 8. Melamine paper takes shape easily, is widely used for the panel furniture and the decorative yarn. Product Specification: Width: 1230-1260mm or 1300-1800mm Length: 500-1000m For storing: Put it in room to a cool and dry place keep the temperature 20-25°C in room. The best humidity is: 50-60% We can also give you complete decorative solution with Matching Melamine Edge Banding, PU Paper. If you need just need Melamine/prelaminated boards either in MDF / Particle board we can also do so
Senna Plant Benefits For Health: As stated above, senna possesses medicinal value which can provide various health benefits given below. 1. Senna For Constipation: Being a laxative, senna is effective in relieving constipation. It has been approved by the US FDA as a non prescription drug to treat constipation. Senna stimulates the muscles of the colon to push fecal matter through more quickly. Senna leaf acts on the intestinal walls to cause contractions that lead to bowel movements. It softens stool by enabling the colon to absorb water. It can effectively cure even the most severe cases of constipation. The glycosides in it help transport electrolytes, causing bowel movements within 6 to 12 hours of its intake. Senna can be bought as an over the counter (OTC) medication for adults and children above 2 years of age. 2. Great Colon Cleanser: Senna has been regarded as a â??cleansing herbâ?? due to its laxative effects. Senna leaf is used in traditional Chinese medicine to clear away the heat accumulated in the large intestine, helping the body get rid of the stagnant food accumulated in the stomach. Today, it is widely used in cleansing the colon before colonoscopy and other types of colon surgery. 3. Treatment of Hemorrhoids: Senna has been found to be effective in the treatment of anal lacerations and hemorrhoids as it helps reduce swelling and facilitates quick healing. Moreover, since it promotes soft stools, it helps cause easy defecation in pathological conditions like anal fissure. This is due to the fact that after oral ingestion, the compounds in senna get absorbed into the intestinal tract, resulting in the separation of non-sugar parts in the colon. These non-sugar components increase the peristaltic movements by irritating and stimulating the intestinal tract. In this way, it speeds up the passage of stools through the intestinal tract. 4. Treatment of Intestinal Worms: The laxative properties of senna have been found to be useful in the treatment of worms in the stomach and colon.  Senna Medicinal Plant: Nutritional Value: The nutritional value of this herb has been explained in the table below. As evident from the table, it is devoid of calories and fat but a rich source of vitamin B
Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
Commodity: Potassium Amyl Xanthate Product Nature Chemical name: Potassium Amyl Xanthate (PAX) Equivalent to : Z-6, AERO 350 xanthate Molecular Formula: C5H11OCSSK Physical characteristics: Slight yellow or grey yellow free flowing Powder or pellet and soluble in water. It is a xanthate based on the C5 alkyl isoamyl alcohol in the potassium salt form Testing method: Lead acetate titration CAS Number: 2720-73-2 EINECS No.: 213-180-2 Use A Collector With High Collection And Normal Selectivity,widely Use In Floatation Of CU/PB/NE AND PYRITE, Especially For The Floatation Of The Gold In Gold And Copper Mine.it Could Make Good Result In Copper And Lead Oxidized Ore.ofeen Used In Rough Selecting And Scavenging. Specifications Chemical components Specification 1 Specification 2 Purity 85% Min 90% Min Moisture & volatiles 10% Max 4% Max Free alkali 0.5% Max 0.2% Max Packing and Storage 120KG IRON DRUM,134 DRUMS PER 20'FCL,16.08MT; (OR 110-180KG IRON DRUM) 850KG Wooden Box,20 Box Per 20'fcl,17mt; (or 500kg,800kg,850kg Wooden Box With Inner BAG) 25-50KG WOVEN BAG
Commodity:Avobenzone CAS No. 70356-09-1 Molecular Formula C20H22O3 Molecular Weigh 310.39 EINEC No. 274-581-6 Specification Quality standard: USP36 Appearance Off-white powder Assay 95.0-105.0% Melting range 81.0~86.0 Impurities Any individual impurity: 3.0% The sum of all of the impurities: 4.5% Loss on drying 0.5% Packaging and storage: 1kg/aluminum foil bag. 25kg/barrel, pharmaceutical packaging barrel. Sealed, stored in dark, with a shelf life of 2 years. Reference dosage: The hygiene standards for cosmetics stipulate that the maximum amount added shall not exceed 5%, and the general dosage is 1-4%. Usage: Sunscreen agent-1789 is the most effective fat soluble UVA filter and is a safe and effective UVA sunscreen approved by the US FDA for sale on the counter. It can effectively block UVA, thereby increasing the SPF value of sunscreen products. It can improve the efficacy of sunscreen products when used in combination with UVB filters, and BL-200 has the best effect when used in combination with octyl methoxycinnamate. BL-200 can increase its stability in the product. It has an extremely effective protective and repairing effect on human skin. Application: This product is soluble in oil and can be formulated into a cream using the usual method. However, the product turns red when it encounters metal ions, so other components such as formula water should not introduce metal ions. The equipment should be made of pure stainless steel, and an appropriate amount of EDTA-2Na should be added to the formula water phase to chelate with metal ions.
Commodity: Caustic Soda Flakes Caustic Soda Pearls / Bead / Prill / Granule Caustic Soda solid Molecular formula: NaOH Molecule Weight: 40 H.S code: 28151100 CAS: 1310-73-2 UN number 1823 Dangerous Class 8 We use rich natural gas resources and its strategic of liquid alkali procurement, storage, transport conditions, gradually formed transportation and sale of liquid alkali, production and sales base and external processing of flake caustic, solid caustic soda, granular caustic soda, which provide ideal condition and environment for domestic and foreign trade. Typical Specifications: Indexes Purity NaCl Na2CO3 Fe2O3 99 99 0.15 0.9 0.003 98 98 0.15 0.5 0.002 96 96 2.8 0.85 0.005 Used as a raw material in the manufacture of soaps ,detergent, textiles and paper ,and likewise ,in water softening and treatment, drilling mud in oil field, refining petroleum products, and washing beer and soft drink bottles, in food and drug industry ,it is used as acidity regulator, alkali, and so on. Packing :Flake/pearl:25kg/plastic woven bag with PE inner Solid :200kg/ iron drum Loading weight in 1 x 20fcl: 27mt
Commodity:Sodium persulfate Molecular Formula : Na2S2O8 Molecular weight : 238.13 Description Sodium persulfate is a white,crystalline,odourless salt.It is used as initiator for the Polymerization of monomers and as a strong oxidizing agent in many applications.It has the particular advantage of being almost non - hygroscopic,of having a particularly good storage stability as a result of its extremely high purity and of being easy and safe to handle. Transportation Road/Rail transport : GGVS,GGVE,ADR,RID/CLASS 5.1 Sea transport : GGV Sea/IMDG code : CLASS 5.1 Page 5185,UN no.1505 Water hazards class 1(slight water hazard) All information is given in good faith,but without warranty,since the conditions of use are outside our control. Verification by the user is recommended.Freedom from patent restriction cannot be assumed. Package (1) In 25kgs net multiple paper bags with one PE bag inner (2) In 25kgs net PE bags (3) In 25kgs net woven bags with two PE bags inner (4) In 1000kgs net big woven bags with one PE bag inner The above package is also with a pallet 1000kgs each. Storage NPS(SPS) is not combustible but assists combustion materials due to release of oxygen.Provided it is stored under appropriate condition.It must be stored dry in closed containers and protected from direct sunlight,heat and humidity.Impurities such as dirt,rust or traces of metal and reductants may cause catalytic decomposition.The product as supplied or in solution needs to be handled with appropriate care.The eye,skin and clothes must be protected when working with NPS(SPS) as damp powder or aqueous solution has a bleaching and slightly corroding effect. Application Polymerization : Initiator for the emulsion or solution Polymerization of acrylic monomers,vinyl acetate,vinyl chloride etc.and for the emulsion co-polymerization of styrene,acrylonitrile,butadiene etc. Metal treatment : Treatment of metal surfaces(e.g. in the manufacture of semiconductors; cleaning and etching of printed circuits),activation of copper and aluminium surfaces. Cosmetics : Essential component of bleaching formulations. Paper : modification of starch,repulping of wet - strength paper. Textile : Desizing agent and bleach activator - particularly for cold bleaching.(i.e.bleaching of Jeans). Others : - Chemical synthesis - Water treatment(decontamination) - Waste gas treatment,oxidative degradation of harmful substances(e.g.Hg) - Disinfectant ITEMS SPECIFICATIONS Appearance white crystalline salt Assay 99.0% w/w min Active oxygen 6.65% w/w min Chloride and chlorate(as CL) 0.005% w/w max Ammonia (NH4) 0.05% w/w max Manganese(Mn) 0.0001% w/w max Iron(Fe) 0.001% w/w max Heavy metals(as Pb) 0.001% w/w max Moisture 0.05% w/w max Decomposition of the product as supplied at above 65C Recommended storage temperature Normal Temperature Storage stability as from date of delivery 12 months
Product Nature Chemical name:Potassium Amyl Xanthate (PAX) Equivalent to : Z-6, AERO 350 xanthate Molecular Formula: C5H11OCSSK Physical characteristics: Slight yellow or grey yellow free flowing Powder or pellet and soluble in water. It is a xanthate based on the C5 alkyl isoamyl alcohol in the potassium salt form Testing method: Lead acetate titration CAS Number: 2720-73-2 EINECS No.: 213-180-2 Use A Collector With High Collection And Normal Selectivity,widely Use In Floatation Of Cu/pb/ne And Pyrite,especially For The Floatation Of The Gold In Gold And Copper Mine.It Could Make Good Result In Copper And Lead Oxidized Ore.Ofeen Used In Rough Selecting And Scavenging. Specifications Chemical components Specification 1 Specification 2 Purity 85% Min 90% Min Moisture & volatiles 10% Max 4% Max Free alkali 0.5% Max 0.2% Max Packing and Storage 120kg Iron Drum,134 Drums Per 20'fcl,16.08mt; (or 110-180kg Iron Drum) 850kg Wooden Box,20 Box Per 20'fcl,17mt; (or 500kg,800kg,850kg Wooden Box With Inner Bag) 25-50kg Woven Bag
FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
Roasted Guar Korma has been developed as a product free of antinutritive factors with balanced Amino Acid Profile. Suitable for Poultry, Swine, Ruminant and Aquaculture. Processed with heat and steam, inactivates harmful trypsin inhibitor which indirectly enhances protein and Amino acids digestibility in the product resulting in increased productivity of livestock and poultry. This process also reduces gummy substance by hydrolysing glactomannan and heat breaks cell walls resulting in higher digestibility of Guar Korma. The anti-nutritive trypsin inhibitor is present in both Soybean and Guar seed, but gets inactive when processed into Soybean meal and Guar meal respectively. We have two qualities of Roasted Guar Korma namely ULTRA and PREMIUM In Roasted Guar Korma ULTRA, the minimum protein content is 48 % and in Roasted Guar Korma PREMIUM, the minimum protein content is 55 %. The other nutritional and Amino Acid values of ULTRA and PREMIUM Roasted Guar Korma are listed below:- • Higher percentage of Crude Protein (CP) • Free From Aflatoxins • Higher Digestibility Index, due to the removal of anti-nutritive factors • More desirable and balanced Amino acid Profile • Higher Energy content and fat percentage • Lower percentage of less digestible Fibre • Higher Palatability, complete elimination of characteristic bean odour and taste. • Low content of Total Volatile Nitrogen (TVN) • Free flowing, uniform fine particle size with good fat and water binding ability NUTRITIONAL VALUES ULTRA PREMIUM Protein 48% – 50% 55% – 60% Metabolize Energy 2550 KCal/Kg 2700 KCal/Kg Moisture Less Than 8% Less Than 6% Fiber 6% – 8% 4% – 5% Fat 5.00% 5.00% Ash/ Sand Silica Less Than 2% Less Than 1% Calcium 0.55% 0.55% Phosphorus 0.68% 0.68% Available Phosphorus 0.19% 0.19% Urease Activity Less Than 1% Less Than 1% Pepsin Digestibility 85.00% 85.00% Trypsin Inhibitor Less Than 1 Less Than 1 Aflatoxins NIL NIL Salmonella NIL NIL E.Coli NIL NIL
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Magnesia Bricks Description Magnesia Bricks are alkaline refractory materials. These products have over 90% magnesium oxide content and adopt periclase as the principal crystalline phase. Magnesia Bricks can be divided into two categories of Burnt Magnesia Bricks and Chemical Bonded Magnesite Brick. They have excellent performance of superior high temperature mechanical strength and volume stability. Magnesia Bricks can service in the high temperature of 1750.. They are ideal products for glass furnace application. Magnesia Bricks Features: It is a kind of alkaline refractory product with periclase as main phase magnesite-alumina spinel clinker as basic material. the product has such characteristics as good temperature vibration, good strength and volume stability in high temperature. Magnesia Bricks Application Basic open-hearth furnace for steelmaking Electric furnace bottom and wall Permanent lining of oxygen converter Non-ferrous metal metallurgy furnace Hyperthermia tunnel kiln Lining of rotary cement kiln Heating furnace bottom and wall Regenerative chamber of glass furnace Magnesia Bricks Properties High Refractoriness Good alkaline slag erosion resistance High apparent initial softening temperature Good thermal conductivity High thermal expansion Magnesia Bricks Manufacturing Process Burnt Magnesia Bricks are manufactured with magnesite clinker as the raw material and fired in the high temperature of 1550~1600 after smashing, burdening, mulling and molding. High-purity products can be fired in the temperature that over 1750. Chemical bonded magnesite brick is produced with certain chemical bonding through mixing, molding and drying.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.