Cnmi Cosmetic Grade Mica Powder Epoxy Resin Dye Suppliers and Manufacturers

METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

1.Chemcial name: Glycolic acid 2.CAS NO.:79-14-1 4.EINECS: 201-180-5 5.Molecular Fomula: C2H4O3 6.Molecular Weight: M=76.05 7.Synonyms: Hydroxyacetic Acid,acide hydroxyacetique C. What is Glycolic acid Glycolic acid is a natural ingredient derived from sugar cane, though it is now often made synthetically. Glycolic acid has a cosmetic grade.

[Alias] foaming powder; sodium lauryl sulfate; sodium lauryl sulfate; sodium dodecyl sulfate, sodium dodecyl sulfate [English name] Sodium dodecyl sulfate. [Abbreviation] SDS [CAS No.] 151-21-3 [Molecular formula] ROSO3Na R = C12alkyl, C12-C14alkyl [Molecular weight] 288.38 (R = C12alkyl), 296 (R = C12-C14alkyl) [Grade] It can be divided into industrial grade (GB/T15963-2008), toothpaste grade (QB/T2900-2012), latex grade and reagent grade according to application fields and standards. [Technical Indicators] [Performance and Applications] This product is a white or yellowish sticky substance, commonly used in detergents and textile industry. Belon to an anionic surfactant.It is easy to dissolve in water, has good compatibility with anions and nonions, and has good emulsification, foaming, penetration, decontamination and dispersion properties. It is widely used in toothpaste, shampoo, shampoo cream, shampoo, washing powder, liquid washing, cosmetics and plastic demoulding, lubrication, pharmaceutical, papermaking, building materials, chemical and other industries. (1) Used as detergent and textile auxiliaries, also used as toothpaste foaming agent, mine fire extinguishing agent, emulsion polymerization emulsifier, wool detergent, etc. (2) Used as anionic surfactant, emulsifier and foaming agent (Use 3) GB 2760-96 stipulates that it is a processing aid for food industry. Blowing agent; emulsifier; anionic surfactant. Used for cake, beverage, egg white, fresh fruit, fruit juice beverage, edible oil, etc. (4) It is used as an emulsifier for drugs, cosmetics and synthetic resins. Foaming agent for toothpaste and fire extinguisher. Used as a detergent for fine silk and wool fabrics. Flotation agent for metal beneficiation. (5) Used as detergent and textile auxiliaries, also used as toothpaste foaming agent, fire extinguishing foam liquid, emulsion polymerization emulsifier, pharmaceutical emulsion dispersant, shampoo and other cosmetics, wool detergent. (Use 6) Biochemical analysis, electrophoresis, ion pair reagent

Commodity: Sodium Sulphate anhydrous Product Nature Molecular formula: Na2SO4 Molecular weight: 142.04 Property: white granular crystal or powder Use As filler of detergent, the making of sodium sulphide, water glass, or used in papermaking, glass, dye and used as filler, dyeing auxiliary, laxative, antidote, t also can be used in fiber, leather, metallurgy, enamel and soap. Specifications Item GB6009-2003 Type First grade Result of common product Result of neutral product Na2SO4 99.0 99.20 99 40 Water insoluble matter %0.05 0.02 03 Ca & Mg %(Mg) 0.15 0.02 02 Chloride %(Cl) 0.35 0.23 20 (Fe) 0.002 0.0001 0001 Moisture % 0.20 0.02 02 Whiteness % 82 88 85 Packing and Storage Knitted bags lined polyethylene plastic bags double packaging, Weighing 25Kg/50KG/1000Kg. Transportation-and harsh rain. Stored in a cool, ventilated, dry place.

Formula:KAl(SO4)2 12H2O Relative Molecular Weight:474.39 CAS NO,: 7784-24-9 EINECS No.:5637-689-7 HS CODE.: 2833301000 Appearance: lump, white crystal, white powder Properties:Colorless, transparent, particle or crystalline powder, odorless, nontoxic, tastes slightly sweet and puckery, astringent, easily soluble in water, its water solution appears acid,is would lose crystal water and become white powder on heating Usage; Food industry: Buffering agents and leavening agents in food-grade products. Chemical Industry: Water Flocculant, aluminum tanning agents and after-treating agents for leather tanning in the leather industry, dyeing agents,Astringents,mordants etc. Items Specifications Potassium aluminum sulfate [AlK(SO4)2.12H2O] % 99.5 Plumbum(Pb) mg/kg 5.0 Arsenic (As) mg/kg 2.0 Fluorine (F) mg/kg 30.0 Selenium (Se) mg/kg 30.0 Moisture % 4.0

ProName: Acetone oxime ,Acetoxime CasNo: 127-06-0 Molecular Formula: C3H7NO Appearance: White crystal ProductionCapacity: 1-100 Metric Ton/Month Grade: Industrial Grade Specifications: index value appearance white crystalline powder or flakes Assay 99.0% residue on ignition 0.01% Boiling point 135 c at 1,013 hpa Moisture 0.25% Uses: It is used as raw material for medicine, pesticides, dyes and organosilane coupling agents. It is also useful in the determination of nickel and cobalt. Acetone oxime is an excellent corrosion inhibitor (deoxidant) with lower toxicity and greater stability compared to hydrazine. Package: 25kg carton drum or 1kg foil bag or by request of clients Storage: Store in dry, dark and ventilated place Transportation: by sea or by air

Commodity : Soda Ash Light / Dense Molecular formula:na2co3 Molecule weight:105.99 H.S Code:28362000 Cas: 497-19-8 Properties : white crystal powder, easily soluble in water, water solution is alkali. Easily absorbing moisture and co2 if exposing in the air. Applications: mainly used in glass-manufacturing, chemical industry, metallurgy, paper, dye, synthetic washes and petrochemistry. Packing :25kg/ 40kg/50kg/750kg pp woven bag with waterproof pe inner , two layers Specifications standard : gb210.1-2004 Items : specification First grade : specification Second grade Total alkalinity(as na2co3 in dry base) %99.2% min98.8% min Chloride content(as nacl) %0.7% max0.9% max Iron content(as fe in dry base) /%0.003% max0.0035% max Sulphate content(as so4 in dry base) /%0.03% max0.03% max Water insoluble matter /%0.03% max0.03% max Loss on ignition a/ %0.5% max0.5% max

Commodity: Sodium Bisulfite Molecular Formula: NaHSO3 Molecular Weight: 104.06 Properties: White monoclinic crystalline powder with sulfur dioxide odor; relative density: 1.49; very easily soluble in water; can be decomposed when heated; slightly soluble in ethanol; aqueous solution is acidic; has strong reducing property; can be oxidized in the air or loose sulfur dioxide. Quality Standard: HG/T3492-80 Technical Indicator High-purity grade Acrylic grade Food grade Refined grade Industrial grade 1 NaHSO3 % 99.5 Insol. in water % 0.003, 0.005, 0.03, 0.04, 0.05 Chloride(Cl) % 0.003, 0.004 Iron(Fe) % 0.001 0.002 0.005 Heavy metal(Pb) 0.001 Arsenic(As) % 0.0001 Clarity test Qualified Use: It is used in the bleaching of cotton textiles; as reducing agent in dyes, paper-making, leather, chemical synthesis; in the manufacture of pharmaceutical intermediates, developer, food bleacher, antiseptic and anti-oxidants. Packing: In PP woven bag lined with PE bag; paper-plastic composite bag, and kraft paper bag etc. Net wt.: 25/50/1000 kgs/bag or upon clients' request.

4-Hydroxybenzoic acid Chemical Name:4-Hydroxybenzoic acid Trade Name:p-oxybenzoic acid Molecular Formula:C7H6O3 Molecular Weight:138.12 CAS No.:99-96-7 Properties:white odorless crystalline powder, easily soluble in hot water and alcohols, aethers and acetone, slightly soluble in cold water and benzene, insoluble in carbon bisulfide; relative density is 1.46 Use: Can be used as antiseptic, intermediate of dyes, pharmaceuticals; as main material of liquid crystal polymers; as material of pesticide intermediate Specification Item Specification Polymer Grade Technical Grade Appearance white crystal powder white crystal powder Purity(on dry base) % 99.6 99.0 Melting Point 214-217 212-216 Odor odorless odorless Solubility Clear and transparent clear and transparent Loss on Drying % 0.20 0.50 Color(Pt-Co) 10 40 Ash % 0.02 0.15 Sulfate(SO42-) 0.01 0.05 Chloride(Cl-) % 0.005 0.02 Phe% 0.01 0.10 Salicylic Acid % 0.02 0.10 4-Hydroxyisophthalic Acid(HIPA) ppm 500 / Insolubles in Metha ppm 50 / Potassium(K+) ppm 5 / Sodium (Na+) ppm 5 / Iron (Fe) ppm 5 / Ca2++Mg2+ppm 5 /

Product Name Sodium Benzoate Specification Food Grade Appearance White Powder/Granular/Sphere Certification FDA, GMP, HACCP, ISO, KOSHER, QS, Halal Purity: 99.5% min [Molecular formula] C7H5NaO2 [Molecular weight] 144.11 [Use] widely used in food industry as Antiseptic, anti-animalcule and antifreezing agent used in food, medicine, tobacco, plating, printing and dyeing [Quality index] in accordance with GB1902-2005 standard for edible grade and BP98 and China national codex 2000 for medicinal grade Package: 25kg net packed in woven bag, or 600kg net packed in ton bag Container: 17MTS/20'FCL without pallets, 14MTS/20'FCL with pallets For extruded, 16MTS/20' container For powder: 17MTS/20' container For granule: 20MTS/20' container Item GB1902-94 version BP98 version China pharmacopoeia 2000 version Content(base on C7H5NaO2 dry basis),% 99.0 99.0-100.5 99.0 Drying loss,% 1.5 2.0 1.5 Dissolve Meet the stipulation Meet the stipulatio Transparency and color / Meet the stipulation Alkalinity acidity; Meet the stipulation Meet the stipulation Meet the stipulation Cchloride (base on Cl) 500PPm 200PPm/ Chloride(base on Cl),/ 300PPm/ Heavy metal(base on Pb) 10PPm 10PPm 10PPm As(base on As),2PPm/ 5PPm Sulfate (base on SO4),1000PPm // Readily oxidizable substance Passed the test/ o-benzene tricarbonic acid Passed the test/

Commodity: Sodium Hydrosulfite Other name: Synonyms: Sodium Hydrosulphite; Sodium Dithionite; Dithionous acid, Disodium salt; Sodium Sulfoxylate CAS No.: 7775-14-6 Molecular Weight: 174.10 Chemical Formula: Na2S2O4 Product Description Appearance: White, crystalline powder. Product Feature Odor: Slight irritative. Specific Gravity: Unavailable Solubility: Soluble in water. Density: 2.19 pH: 6-7 pH Test-Method: PH test paper. % Volatiles by volume @ 21C (70F): 0 Boiling Point: Not applicable. Melting Point: >300 C Decomposes. Vapor Pressure (mm Hg): No information found. Bulk Density: ~0.9 Evaporation Rate (BuAc=1): No information found. Application 1. Widely used in textile industry for vat dyeing, reduction cleaning, printing and stripping, textile textile bleaching . 2. bleaching paper pulps , especially mechanical pulps, its the most fittable bleaching agent in pulps. 3. bleaching kaolin clay, fur bleaching and reductive whitening, bleaching of bamboo products and straw products, 4. in mineral, the compound of thiourea and other sulphides. 5. as reducing agent in chemical industry. 6. Sodium hydrosulfite food additive grade is used in foodstuffs, as bleaching agent and preservative dried fruits, dried vegetable, vermicelli, glucose, sugar, rock sugar, caramel, candy, liquid glucose, bamboo shoots, mushrooms and canned mushrooms. Packaging 50kg/100kg net in iron drums with double PVC bags Product Specification/Models NDEX 90%, 88%, 85%. FOOD ADDITIVE Na2S2O4, 90%, 88%, 85%, Fe 20ppm ZincZnOther heavy metal calculated as Pb, 1ppm Water Insolubles05% Shelf Life(month)12

Food Grade Guar Gum Powder is extensively used in different industries such as food, pharmaceutical, and cosmetic industries. Also, we offer different types of guar gum powder which are produced in accordance with the industrial norms and standards. Food Grade Guar Gum Powder is one of the best thickening additives, emulsifying additives and stabilizing additives. In Food industry guar gum is used as gelling, viscosifying, thickening, clouding and binding agents

Guar Gum Split is refined endosperm derived from guar seed or cluster bean (cyamoperm tetragonoloba). Guar Splits are non-ionic polysaccharide galacomannan. Guar Gum Refined Split (Endosperm) is mechanically separated from guar seed which yields 28-30% of Refined Split. Guar beans are harvested and dried following the growing season. The beans are shelled from the pods, the germ and hull removed. The resulting guar splits are wet-milled into powder; the powder is graded by granulation and quality. Products are re-blended according to specification, bagged and marked. Guar Gum Split with its versatile inherent properties is used all over the globe with different utilities in many industries like Petroleum (Oil drilling), textile, printing, food pharma, cosmetic, toiletries paper, tanneries, mining, explosives, pet food etc. in powder form either directly plain Guar Gum Powder or in derived form. Uses : Guar Gum Split with its versatile inherent properties is used all over the globe with different utilities in many industries like Petroleum (Oil drilling), textile, printing, food pharma, cosmetic, toiletries paper, tanneries, mining, explosives, pet food etc. These industries use Guar Gum in powder form either directly plain Guar Gum Powder or in derived form. We provide quality Guar Gum Splits to quality manufacturer of Guar Gum Powder, which is their pre-requirement for manufacturing high quality Guar Gum. Specifications: Color Pale-white Gum Content 80-85% Splits 92-98% Mineral Matter (ASH) 1.5% max Fiber 1.5 – 2.0 % max Protein 5% Maximum Ether Soluble Substances 0.6% Maximum Acid insoluble ash (sand and/or silica) Traces Black Split 1% max Heavy Metals Nil Appearance Bright creamy yellow Packaging: Type of Bags Quantity HDPE Bags 50.00 Kgs Jumbo Bags 1000.00 Kgs