Glassfibre chopped strand mat (briefly as CSM) is an non-woven E-or C-glassfiber glassfibre which is made of chopped strands of 50mm in length, which are randomly and uniformly dispersed and bound together with polyester binder in powder or emulsion form. Uniform density, no any other impurity. Proper rigidtitly, Excellent flexibility. Good permeability easy for deaeration, good technics Excellent processability in moulded parts, applying for diversity moulding and processing. Specially in opened moulding and closed moulding Good mechanical physics and chemistry properties. packing storage and transport Products package and storage, transportation Chopped strand mat will be wrapped up paper pipe of 76mm inner diameter, and polyvinyl chloride film will be used for packing and sealing and then package them with carton.such as width of 1040mm,The carton size will be:28L*28W*H1070cm the mats should be put horizontally or vertically. It¡¯s allowed to be packaged by bulk and pallet when shipping by containers.When package by pallet ,each pallet vertially 16 cartons.The pallet size will be :112L*112W*H10 cm Chopped strand mat should be reserved indoor with drying, cool, wet-proof and rain-proof condition. It suggests that temperature should be control within 1535 and humidity should be control within 35%¡«65%. The covering memberane shall be no opened until applying The products are suitable for all kinds of FRP process, such as handing lay-up, Filament winding, molding process. Centrifugally cast filled process. mechanical process,etc..It is widly used for automobile parts, sanitary wares, chemical corrosion resistance pipe, cooling tower, storage tank, ships manufacture, building materials, furniture and so on.
性能 Property 玻璃 类型 Glass type 单位面积 质量 Area weight G/m2 幅宽 Width 200 Mm 卷重 Roll weight ㎏ 含水率 Moisture Content % 可燃物含量 Combustible Content % 断裂强度 Breakage strength N 测试方法 Test method Gb/t 1549 Iso3374 Iso3374 Gb/t17470-1998 Iso3344 Iso1887 Iso3342 Emc80 E/c-glass 80¦16 ¦5 6
Fiberglass chopped strand mat, both powder and emulsion type. E-glass. For reinforcing GRP/FRP product, used together with polyester, vinylester resin by hand lay up process. Weight: 100g/m2 - 900g/m2 width: 100mm-2600mm
Chopped strand mat Product code Area weight g/m2 Width mm Wet out speed s Styrene solubility s Moisture Content % Binder EMC series 100-900 100-3000 â?¤100 â?¤40 â?¤0.20 Polyester Powder Chopped strand mat is mainly used to process FRP products through hand lay-up molding process, winding molding process, and molding molding process. This product is mainly used in car ceilings, bathroom fixtures, pipes, building materials, automobiles, furniture and other fiberglass products
Chopped strand mat Good drapability Easy impregnation Fast wet-through and de-airing High mechanical properties of the laminate Film + carton box + pallet * 18 tons per container
Fibreglass Chopped Strand Mat Emulsion bonded Density 300/450/600 GSM Width 1.04 meteres
Fiberglass chopped strand mat, briefly as csm, is a kind of reinforcing product that made from continuous fiberglass strand, which is chopped into a certain length, distributed in an random and non-directional position and bonded with binders. It is suitable for hand lay-up, mold press, filament winding and mechanical forming ect., such as grp processes. The main products include kinds of panels, boats, sanitary ware, water tank, anticorrosive engineering products, storge tank, automobile parts and cooling towers etc.
"DD fiberglass" Fiberglass chopped strand mat Glass type: e-glass, c-glass; Area weight: 150, 225, 300, 450, 600g/m2; Width: 1040mm, 1250mm. Binder: powder, emulsion. Film, carton
Fiberglass chopped strand mat , 225/300/450gsm powder/emulsion binder 450gsm, 1040mm, 76m .
300/450/600/225 gsm powder/emulsion binder Woven roving 400/600/800gsm Direct roving 1200/2400/4800tex Fiberglass mesh Chopped strands for smc/bmc 3/4/6/12mm. According to customer requriement
E-glass chopped strand mat We are the manufacturer and exporter specialized in e-glass chopped strand mat in china, the capacity is about 6500mt per year, the normally specifications are 300g/m2, 450g/m2, 600g/m2 and the width is 1000mm, 1040mm, 1250mm, 1270mm, 2540mm ect, powder or emulsion bind! quality products, competitive price and fast shipping, we sincerely wish we can have the chance to cooperate in near futurer. 30kg/roll, 300gsm, 1040mm*76ooomm
This product have excellent properties of resin impregration, easy mouldability, which is mainly for the applications by hand lay-up frp mouldings such as various sheets and panels, boat hulls, bath tube, cooling towers, etc. Features: 1. Weight/m2: 200g/250g/300g/450g/600g, etc 2. Binder type: powder, emulsion 3. Roll width: 1. 04m, 1. 27m, 2. 08m 4. Roll weight: 30 kg or 35kg/roll 5. Packing: inner plastic bag and outer carton.
Fiberglass chopped strand mat With the characteristics of non-directional and even distribution, high mechanical kinetics. With fine plating and fitting for complex shapes of moulders. Well-soaked with resin, cutting freely, working simply. With high strength of absorbing resin, smooth appearance. Specification Package First sealed with pvc film, then packed in the cardboard box. Standard weight: 250g/¼o, 300 g/¼o, 380 g/¼o, net weight 30kg per box.. Standard weight: 450 g/¼o, 600 g/¼o, net weight 35kg per box.
we are the professional manufactory of Chopped Strand Mat, we have 1800 tons capacity per month and three production line , we can produce 100-900 gsm form width 15mm to 3600mm. as the only one fiberglass manyfactory in Thailand , most of our product sales to Euro markat
Chopped Strand Mat Fiberglass Chopped Strand Mats are non-woven fabrics consisting of randomly distributed chopped strands held together with a powder or emulsion binder. Chopped Strand Mat is compatible with unsaturated polyester, vinyl ester, epoxy and phenolic resins. The products are most widely used in hand lay-up process and can also be used in filament winding, Compression molding and continuous laminating processes. The typical end-use applications include various panels, boats, FRP roof shoot, Autonitive parts, bathroom equipment and cooling towers. Product Features 1.Uniform density ensures consistent fiberglass content and mechanical properties of the composites products. 2.Uniform powder distribution ensures good mat integrity, little loose fibers and small roll diameter. 3.Excellent flexibility ensures good moldability with no spring-back at sharp corners. 4.Fast and consistent wet-out speed resins and rapid air release reduce resin consumption, improving manufacturing costs, productivity and mechanical properties of the end products. 5.The composite products have high dry and wet tensile strength and good transparency. General Data Binding type : Powder or Emulsion; Densily : 85-900g/m2; Width : Max.3300mm, Tapes available. Edge : 1 or 2 untrimmed edge available upon request.
300g fiberglass mat/ chopped strand mat/ csm/ sheet/ felt 1.Introduction E-glass chopped strand mat is made of randomly distributed chopped strands held tighter by a emulsion/ powder binder. It is compatible with unsaturated polyester, vinylit, epoxy resins. The roll width ranges from 50mm to 2080mm. Special requirements may be available upon request. 2.Usage It is used for processing and manufacturing frp products with getting through hand lay up process, filament winding process and press molding. Typical products is including bathroom accessories, pipe, building material, automobile, furniture, vessel, cooling towers and other frp products 3.Packing Product is manufactured in form of a roll wound on a paper tube and then packed in a plastic film and placed within a cardboard carton. Rolls can be loaded into a container directly or on pallets. 4.Parameter Density(g/m2Moisture content (%Loss on ignition (%Binder typeWidth (mm) 2250.22.1-6.3Powder/ emulsion1040 1270 2080 2500.22.1-6.3Powder/ emulsion1040 1270 2080 3000.22.1-6.3Powder/ emulsion1040 1270 2080 4500.22.1-6.3Powder/ emulsion1040 1270 2080 6000.22.1-6.3Powder/ emulsion1040 1270 2080
E glass chopped strand mat E glass chopped strand mat is made from e-glass chopped strands around 50mm in length, bonded together by powder or emulsion binder which is extremely soluble in styrene. The basic strand has a sizing system containing a silane coupling agent. 1. Excellent impregnation properties 2. Excellent conformability 3. Good mechanical properties 4. Good drapability 5. High tensile strength
Glass;Fiber Chopped Strand Mat Description E-Glass Fiber chopped strand mat is a kind of non-woven glass fiber reinforced material, which is made by chopping glass fiber first, then be settled down non-directional and uniform, adding some powder or emulsion binder. It is mainly used for hand laying up process ;and laminating process, ;easy to process, with excellent ;forming performance. Chopped strand mat ;can be saturated with resin ;fast, ;with high ;transparency,;at the same time, uniform fiber ;makes the products ;smooth on surface ;during the lamination process,good performance on coating model. Glass;Fiber Chopped Strand Mat Characteristics 1)Weight is evenly distributed per gram 2)Saturated fast, 3)Bubbles easy ;to be eliminated, 4)High transparency 5)Excellent coating model;performance 6)Less;consumption of ;resin. Glass ;Fiber Chopped Strand Mat Application Mainly used for;tank, winding pipe;products,;the surface layer;of the glass products. Can improve the;surface;corrosion resistance and;enhance the;compressive strength for finished fiber glass products,;prevent leakage,;prolong the service life. Hand laying up;type glass;fiber mat ;is mainly used for;hand laying up ;product;with complex geometric curve,;it is with excellent coating model performance,rapid resin;saturated speed, canimprove the strength and;corrosion resistance performance for finished glass fiber mat products. Glass;Fiber Chopped Strand Mat Technical Parameters ModelTypeMass per Unite Area(g/m2)WidthLinear density(172;m) Loss on lgnition(%) WDQ150 E-Glass 150 104011-13 1.5%-8.5% WDQ225 E-Glass 225 1040 11-13 1.5%-8.5% WDQ280 E-Glass 280 1040 11-13 1.5%-8.5% WDQ300 E-Glass 300 1040 11-13 1.5%-8.5% WDQ450 E-Glass 450 1040 11-13 1.5%-8.5% ZDQ280 C-Glass 280 1040 13-17 3.0%-6.0% FDQ300 CP-Glass 300 1040 13-17 3.0%-6.0% Glass;Fiber Chopped Strand Mat Packaging Packing Quantity Plastic Film+ Carton Box+Pallet About 10tons/ 20 ft 23tons/ 40ft Plastic Film+ Carton Box+Pallet About 10tons/ 20 ft 23tons/ 40ft
Wdz150# glass, fiber chopped strand mat characteristics Weight is evenly distributed per gram, , can be saturated fast, , bubbles easy, to be eliminated, , with high transparency for finished products, excellent coating model, performance, , less, consumption of, resin. Wdz150# glass, fiber chopped strand mat application Mainly used for, tank, winding pipe, products, , the surface layer, of the glass products. Can improve the, surface, corrosion resistance and, enhance the, compressive strength for finished fiber glass products, , prevent leakage, , prolong the service life. Hand laying up, type glass, fiber mat, is mainly used for, hand laying up, product, with complex geometric curve, , it is with excellent coating model performance, , rapid resin, saturated speed, can, improve the strength and, corrosion resistance performance for finished glass fiber mat products. Wdz150# glass, fiber chopped strand mat technical parameters Model Non-alkali/alkaline Gravity(g/m2) Width¡ê¡§mm) Wdz150# Non-alkali 150 900-3200 Wdz150# glass, fiber chopped strand mat packaging Selling units: Single item Single package size:, 1x1x1 cm Single gross weight: 1.2 kg For more information of wdz150# glass, fiber chopped strand mat, pls feel free to contact aileena Mob:86- 18938867591 , E-mail:, hyl(at)resinpu(dot)com , Skype:liaoyuzhen92 Selling units: Single item Single package size:, 1x1x1 cm Single gross weight: 1.2 kg
Glass, fiber chopped strand mat characteristics Weight is evenly distributed per gram, , can be saturated fast, , bubbles easy, to be eliminated, , with high transparency for finished products, excellent coating model, performance, , less, consumption of, resin. Glass, fiber chopped strand mat application Mainly used for, tank, winding pipe, products, , the surface layer, of the glass products. Can improve the, surface, corrosion resistance and, enhance the, compressive strength for finished fiber glass products, , prevent leakage, , prolong the service life. Hand laying up, type glass, fiber mat, is mainly used for, hand laying up, product, with complex geometric curve, , it is with excellent coating model performance, , rapid resin, saturated speed, can, improve the strength and, corrosion resistance performance for finished glass fiber mat products. Glass, fiber chopped strand mat technical parameters Model Non-alkali/alkaline Gravity(g/m2) Width¡ê¡§mm) Wdz150# Non-alkali 150 900-3200 For more information of wdz150# glass, fiber chopped strand mat, pls feel free to contact amber Tel: +86-0755-89311348 Mob: +86-18938867544 Skype: amberqu2 Email: hyresin@outlook.Com Email: hyresin(at)outlook¡ê¡§dot¡ê©com Glass, fiber chopped strand mat packaging Selling units: Single item Single package size:, 1x1x1 cm Single gross weight: 1.2 kg