Buy Yanmar Nozzle X 7 Yanmar 4Tnv88 Parts Suppliers and Manufacturers

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

Calcium Acetate Monohydrate, E263, CAS no. 5743-26-0, calcium salt of acetic acid, s a white, odorless, and tasteless crystalline powder. Also known as Calcium acetate, manufacturing process via chemical synthesis, calcium carbonate and acetic acid as raw materials. Calcium Acetate Monohydrate is mainly used in the production of candy products, desserts, and baked good (bread, cakes, pastries). As an experienced Calcium Acetate Monohydrate manufacturer and supplier, we has been supplying and exporting Calcium Acetate Monohydrate for almost 10 years, please be assured to buy from us. Any inquiries about price and the market trend please feel free to contact us, we will reply you within 1 working day. Calcium Acetate powder Specification Product Calcium Acetate CAS anhydride :62-54-4; monohydrate :5743-26-0 INS 263 EINECS 200-540-9 EEC E263 Structure Molecular formula 1.Anhydrous:Ca(C2H3O2)2 2.Hydrates:C4H6CaO4H2O 3.C4H6CaO4xH2O(x

We are sellers of certified halal frozen whole chicken, chicken feet, chicken , beef, pork our products meet the SGS testing, we can supply all kinds of frozen chicken cuts. Freezing Process: IQF Part: Whole Shape: Packaging: Cartons Shelf Life: 12 months We supply high quality and large quantities of Halal and non-halal frozen whole chicken, frozen chicken feet and frozen chicken parts. The different types of frozen whole chicken and frozen chicken parts that we supply are: A. Whole chicken. Please indicate the size that you want. B. Chicken leg quarter/Chicken whole leg C. Chicken drum stick D. Chicken thigh E. Chicken boneless leg F. Chicken G. Chicken wing tips H. Chicken 2 joint wing I. Chicken whole leg boneless with skin on J. Chicken feet K. Chicken gizzards L. Chicken wing middle joint M. Chicken inner fillet middle half cut N. Chicken boneless and skinless breast without inner fillet O. Chicken half breast boneless and skinless without inner fillet Q. Chicken head R. Chicken back S. Chicken front T. MDM Specifications: - Feather off - well cleaned and fresh - no bruises - no black pads or ammonia burns - no bad smells - no excessive blood or blood stains - moisture content is less than 3% weight and packaging: whole chicken each weight 800g to 2500g x 7-10 in a box Other parts from 2kg up to 10 - 15/20kg Payment Terms : TT Only

chicken parts; 1. halal whole chicken 2. chicken leg quarters 3. chicken breasts 4. chicken wings 5. chicken feet and paws 6. chicken drumsticks 7. chicken gizzards 8. chicken liver Product description and chemical composition Detailed Description: - Washed and clean. - Without yellow skin. - No feathers. - No bad smell. - No blood. - No bruises. - No black pads. - No traces of carved deep wounds. - No ammonia burns. - Broken bones: under 3%. - Moisture content: less than 1%. - Drainage: 0 to -5 C for 8 hours. - Blasted at: -40 C. - Storage at: -18 C - 100% Fresh and Frozen Safe for human consumption Storage, loading and transportation system. Stored in chill rooms for early dispatch or frozen and stored for dispatch as required Loading is made in refrigerated pallets, containing in each pallet 1MT/1000kg. Our method of packaging, Protects the product from contamination, damage and moisture loss and spoilage by micro-organisms As customer requires, NB: We load 27 metric tons in 1 x 40 feet. We sale best quality Frozen Halal whole chicken and chicken parts like feet,paws,wings,leg,breast,drumsticks .We provide quality goods at very competitive price and we want buyers globally in need of our products contact for details as regards to our goods. 1. frozen whole chicken 2. frozen chicken feet 3. frozen chicken Paws 4. frozen chicken breast 5. frozen chicken thighs 6. frozen chicken drumstick 7. frozen chicken leg quarters 8. frozen chicken wings 9. frozen mid joint chicken

Specifications: Spares part will pack in plastic bubble sheet, after that pack in 5-ply carton, after that shrink wrapping. Then finally pack in size adjusent wooden box. Dome Dia: 70 cm Light Intensity: 1,00,000 Lux Field Size: 20 CM Action Radius:160 cm Color Temp: 4200 K Halogen Bulbs: 12V 55W x 7 Power : 220V AC/DC

Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic

Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium

Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum

V7 Borewell Submersible Pumpset Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Cast iron casting bowl and SS-410 grade impeller in mix flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps Specification - Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW - Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2880 RPM - Head Range : 18 Mtr. To 650 Mtr. - Discharge Range : 1860 LPM to 55 LPM - Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0 - Degree of Protection : IP 58 - Direction of Rotation : Electrically Reversible -3ph - Thrust Load : 11.2 kW -37.3 kW -8000 lbs - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5

We are Brazil Exporter and Importer Certified producers of USA, Brazil, Argentina, UK Halal and non Halal Frozen Chicken. We supply at both CIF and FOB terms at any safe world port. Our product meet both International and National Standards. We can supply various Frozen Chicken cuts such as; We can supply various Frozen Chicken cuts such as; 1. frozen whole chicken 2. frozen chicken feet 3. frozen chicken Paws 4. frozen chicken breast 5. frozen chicken thighs 6. frozen chicken drumstick 7. frozen chicken leg quatars 8. frozen chicken wings We ship directly to all Asian ports, and we are registered to supply and deliver directly to China, Hong Kong, Vietnam,dubai,saudi, Taiwan, Korea, Thailand , Malaysia and other countries.. we produce and supply the best quality of Grade A Frozen Chicken Feet,Paws and other chicken parts Processed Frozen Chicken Paws â?? Grade A Specifications: - White skin - No broken bones 0% - Outer yellow skin off - Well cleaned and fresh - No bruises - No black pads or ammonia burns - No bad smells - No excessive blood or blood stains - Moisture content is less than 3% - Weight per piece is 35-50g - Length per piece 12-15 cm Frozen Temperature: - Blasted at: minus 40 degrees Celsius - Storage at: minus 20 degrees Celsius. - Temperature during Transportation: minus 18 degrees Celsius We package in 20kg carton boxes, each box contains 5kg polybags x 4. Customized packaging of all other sizes are offered, and we also provide labels for buyers. We load 27MT per container 40FT. Processed Frozen Chicken Feet â?? Grade A Specifications: - White skin - No broken bones 0% - Outer yellow skin off - Well cleaned and fresh - No bruises - No black pads or ammonia burns - No bad smells - No excessive blood or blood stains - Moisture content is less than 3% - Weight per piece is 35-60g - Length per piece 14-16cm Frozen Temperature: - Blasted at: minus 40 degrees Celsius - Storage at: minus 20 degrees Celsius. - Temperature during Transportation: minus 18 degrees Celsius We package in 20kg carton boxes, each box contains 5kg polybags x 4. Customized packaging of all other sizes are offered, and we also provide labels for buyers. We load 27MT per container 40FT