** Airless Spray Gun HK-747 OMEGA ** Features [HK-747 OMEGA] - Enhanced precaution for musculoskeletal disorders through soft operation - 30% discharge pressure improved compared to existing models - Dual safety system - Improved leak prevention with faster closing speed of the needle ** Technical Data [HK-747 OMEGA] - Max. Working Pressure : 720kgf/cm² - Burst Pressure : 1,400kgf/cm² - Cast-iron Material : Forged Aluminum - Weight : 480g
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Capsicum Oleoresin is prepared by extracting the crushed capsicum (Capsicum Annum Linn) with volatile solvents by percolation method. It contains the pungent principles, capsicin not less that 8 percent. It also contains the red colouring matter called Capsanthin. This product is a powerful irritant and a carminative, which is also used as a counter irritant in lumbago and neuralgia. It can also be used to treat stomach ache that involves poorly functioning stomach muscles and as an antibacterial agents. Extraction of oleoresin capsicum from peppers involves finely ground capsicum, from which capsaicin is extracted in an organic solvent such as ethanol. The solvent is then evaporated, and the remaining wax like resin is the oleoresin capsicum. An emulsifier such as propylene glycol is used to suspend the OC in water, and pressurized to make it aerosol in pepper spray. The high performance liquid chromatography (HPLC) method is used to measure the amount of capsaicin within pepper sprays. Scoville Heat Units (SHU) are used to measure the concentration or "heat" of pepper spray. A synthetic analogue of capsaicin, pelargonic acid vanillylamide (desmethyldihydrocapsaicin), is used in another version of pepper spray known as PAVA spray which is used in the United Kingdom. Another synthetic counterpart of pepper spray, pelargonic acid morpholide, was developed and is widely used in Russia. Its effectiveness compared to natural pepper spray is unclear. Pepper spray typically comes in canisters, which are often small enough to be carried or concealed in a pocket or purse. Pepper spray can also be bought concealed in items such as rings. There are also pepper spray projectiles available, which can be fired from a paintball gun. It has been used for years against demonstrators. Derived from chilli peppers, oleoresin capsicum is the active ingredient in pepper spray and in some topical pain relievers.
** Airless Spray Gun HK-300 ** Technical Data [HK-300] - Max. Working Pressure : 500kgf/cm² - Cast-iron Material : S45C - Weight : 680g
SHUTTERINGOIL Applied by spraying guns, rollers or by brushes prior to pouring aerated concrete and are recommended for use as a concrete mould release agent with the protection of moulds from rust. APPLICATION \' It is used for prevents sticking of formwork to concrete, allowing easy stripping of formwork after harder�±ng of concrete. , BENEFITS It helps easy removal of the shuttering at time of deshuttering the member whereas the oil must be of good condition. It helps in the repetative use of plywood for more project. It make a thin layer between the plywood and concrete which help in reducing of adhesion in the inner surface.
1. Four fingers 2. Build-in filter 3. Standar G-thread (7/8") 4. Max working pressure: 270bar / 3900psi
Graco Airless Spray Gun Filters Paint Filters & Strainers Filters & Baskets Graco Spray Gun Filter FEATURES Graco Airless Spray Gun Filters, PN 218-133, 218-131, 287-748, 287-032, 287-033 Graco Manifold Filter Stainless Steel PARAMETER Graco Airless Spray Gun Filters, PN 218-133, 218-131, 287-748, 287-032, 287-033 We are a Graco airless spray gun filters and wire screen supplier. If you are interested in our products, please feel free to contact us! YMX FILTER MANUFACTURING CO., LTD is a custom fabricator of series of wire screen, cone strainers and woven wire cloth products. For more than 20 years' experience, we are serving customers from a wide range of industries from all over the world. If you are interested in custom wire screen, you can click here to browse our website.
Airless spray gun filters for graco, Wagner, Spraytech, ASM,Titan. We have different colors for your choice. They are Made from high quality stainless steel wire mesh. Different size for your choice. About the package we usually use valve bag. various sizes
Shot blasting machines, shot peening machines, blast room systems, paint spray booth, baking oven, surface finishing equipments, dust collector, baking booth, pneumatic shot blasting machine, airless shot blasting machine, hanger type shot blasting machine, tumblast type shot blasting machine, rotary barrel type shot blasting machine, roller conveyor type shot blasting machine, diabola type shot blasting machine, table type shot blasting machine, stone texturing machine, paver block shot blasting machine, coil spring shot blasting machine, leaf spring shot blasting machine, structure shot blasting machine..
** Airless Paint Sprayer HK-421 ** Features [HK-421] - Convenience of repair & maintenance - Low-noise design to remove hearing trouble - Reduced freezing with mounted air jet system - Typical fluid handled : Inorganic-zinc, Tar-epoxy, Alkyd, Urethane, High viscosity paint - Application : Container, Pier.Pipe coating, Drum coating, Heavy anti-corrosive coating ** Technical Data [HK-421] - Pressure Ratio : 42:1 - Max. Delivery : 20L/min. - Operating Air Pressure : 3~6.5kgf/cm² - Max. Discharge Pressure : 273kgf/cm² - Dimension(LxWxH) : 68x72x100cm - Weight : 80kg - Noise : 70~80dB - Air Motor Stroke : 120mm
** Airless Paint Sprayer HK-331 ** Features [HK-331] - Low-noise design - High pressure pump of 214kgf/cm² comparing with small size pump - Low-freezing design - Application : Timber products, Finishing coating, Heavy anti-corrosive coating
Tumblast type machines are basically designed for batch type operation. Tumblast Machine consists of Vertical/Horizontal door. Components to be blasted are loaded on to the endless rubber conveyor of the machine from this door. One No. of Blast wheel unit, is strategically placed at the top of the Blast cabinet will fire abrasive at high velocity on the tumbling components and blast cleans them thoroughly. Tumbling action of the rubber belt conveyor ensures that each and every portion of the component will get exposed to the blast stream for through cleaning. For unloading the components from the machine, door of the machine is opened and rubber belt conveyor is made to move in reverse direction and blasted components is then get collected into the Bin/Tray (under customer scope).
Product Details: Product Type L Other Technology : Other Power Source : Pneumatic Operating Type: Semi Automatic Power : 420 Volt (v) Pressure : 6-7 Bar Surface Treatment : Painted Supply Ability : 7-10 Unit Per Month Price Range 50000.00 - 110000.00 INR/Unit Minimum Order Quantity : 1 Unit Power : 420 Volt (v) Operating Type : Semi Automatic Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Pressure 6-7 Bar Color Dark Blue Surface Treatment Painted Weight (kg) Not Applicable Metric Ton Power Source Pneumatic Product Type Other Usage/Applications Casting, Forging, Sheet metal etc Technology Other Applications of the portable blaster : De-sanding and de-coring of castings. Descaling of castings, forgings parts. For creating rough surface inside and outside of heavy structure, pressure vessels, pipes for proper bounding of the primer/paint. Can also be used in Wooden industry for decorative design purpose. For creating textured/rough surface on different type of paving blocks, marbles, granite for their proper bounding on surface. For removal of heat treatment scale, welding flux , corrosion, rusting in steel components. For engraving / creating design, etching on different type of stones and metals. For removal of old paint from metal surface of ships and other structural steel components. Specification: Power 5 Hp Capacity 200 Kg Material Stainless Steel Automation Grade Semi Automatic Application Rust Removal, Surface Finishing Motor Phase Three Phase Voltage 220-240 V | 50 Hz No. of Wheels 3
Product Details: Product Type Other Technology Other Power Source Pneumatic Operating Type Semi Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price Range 50000.00 - 125000.00 INR/Unit Product Specifications: Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Color Dark Blue Power 420 Volt (v) Usage/Applications Casting, Forging, Sheet Metal Technology Other Operating Type Semi Automatic Pressure 6-7 Bar Surface Treatment Painted Power Source Pneumatic Portable Sand Blaster Applications of the portable blaster : De-sanding and de-coring of castings. Descaling of castings, forgings parts. For removal of heat treatment scale, welding flux , corrosion, rusting in steel components. For engraving / creating design, etching on different type of stones and metals. For removal of old paint from metal surface of ships and other structural steel components. For creating rough surface inside and outside of heavy structure, pressure vessels, pipes for proper bounding of the primer/paint. Can also be used in Wooden industry for decorative design purpose. For creating textured/rough surface on different type of paving blocks, marbles, granite for their proper bounding on surface. Specification: Power 7 Hp Capacity 500 Kg Material Stainless Steel Automation Grade Manual Application Paint Removal Voltage 220-240 V | 50 Hz Motor Phase Single Phase No. of Wheels 3
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 4 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price 325000.00 INR/Unit Product Specifications: Usage/Applications Casting, Forging, Sheet metal etc Surface Treatment Painted Power 420 Volt (v) Weight (kg) Not applicable Metric Ton Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Power Source Electricity Product Type Other Operating Type Automatic Pressure 6-7 Bar Color Dark Blue Technology Other Rotary Barrel Shot Blasting Machine Rotary Barrel Type Shot Blasting Machine is widely used in small or medium size iron, steel, alloy and non-ferrous castings, forgings, heat treated parts, pressings and fabrications at the lowest possible cost. The rotary barrel blasting machine employs a specialized internal geometry of the rotating barrel which features contoured ridges on the sides. This design facilitates the multi tumbling action of the drum's rotation, that allows the barrel to topple and mix the workpieces. This action makes sure that the blast stream passes through all surface area, thus providing equal and constant blast results. The machine also provides well-cleaned parts surfaces that are sand, rust, or scale free. It is ideal to use in applications requiring the blasting of small, flat, and light components. Technical Specification: Barrel Size: 649 MM Dia. x 625 MM Length Total Weight Capacity: 100 Kg's Volume: 1.5 CFT Total HP Required: 5 HP Specification: Usage/Application Surface Roughness Preparation Number of Doors Single Door Power Required 5 HP Capacity 0-5 ton/day Driven Type Belt Driven No. Of Blast Wheels 1 Wheel Size (inch) 11.5'' X 2.5'' Model Number BT-RBM-01 Flow Rate (kg per hr.) 1600 Kg/Wheel/Hour Motor Hp 3 HP Brand Adl Blastek Automatic Grade Automatic
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 , , Unit Per Month Price And Quantity: Price 325000.00 INR/Unit Minimum Order Quantity 1 , , Unit Product Specifications: Product Type Other Usage/Applications Casting, Forging, Sheet Metal Weight (kg) Approx. 1 Metric Ton Operating Type Automatic Pressure 6-7 Bar Power 420 Volt (v) Color Dark Blue Power Source Electricity Surface Treatment Painted Technology Other Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Drum Type Shot Blasting Machine Rotary Barrel Type Shot Blasting Machine is widely used in small or medium size iron, steel, alloy and non-ferrous castings, forgings, heat treated parts, pressings and fabrications at the lowest possible cost. The rotary barrel blasting machine employs a specialized internal geometry of the rotating barrel which features contoured ridges on the sides. This design facilitates the multi tumbling action of the drum's rotation, that allows the barrel to topple and mix the work pieces. Technical Specification: Barrel Size: 649 MM Dia. x 625 MM Length Total Weight Capacity: 100 Kg's Volume: 1.5 CFT Total HP Required: 5HP
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price Range 450000.00 - 600000.00 INR/Number Product Specifications: Technology Other Color Dark Blue Power Source Electricity Operating Type Automatic Weight (kg) 3.5-4 Metric Ton Pressure 6-7 Bar Usage/Applications Casting, Forging, Sheet metal etc Power 420 Volt (v) Product Type Other Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Product Description: Tumblast Type Shot Blasting Machine [TB-20X27] Tumblast type machines are basically designed for batch type operation. Tumblast Machine consists of Vertical door. For loading the components, door of the machine is opened manually & components to be blasted are loaded on to the endless rubber conveyor and the door of the machine is closed. After this Blast wheel unit, which is strategically placed at the top of the Blast cabinet, is started. Blast wheel will fire abrasive at high velocity on the tumbling components and blast cleans them thoroughly. The arrangement of the blast wheel ensures optimum blast cleaning and maximum utilization of the abrasive energy.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 5 Unit Per Month Price And Quantity: Price Range 1250000.00 - 1450000.00 INR/Number Minimum Order Quantity 1 Unit Product Specifications Pressure 6-7 Bar Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Product Type Other Power Source Electricity Usage/Applications Casting, Forging, Sheet metal etc Power 420 Volt (v)Operating Type Automatic Technology Other Surface Treatment Painted Color Dark Blue Product Description: Tumblast Shot Blasting Machine [TB-36X42] Tumblast type machines are basically designed for batch type operation. Tumblast Machine consists of Vertical door. For loading the components, door of the machine is opened manually & components to be blasted are loaded on tote endless rubber conveyor and the door of the machine is closed. After this Blast wheel unit, which is strategically placed at the top of the Blast cabinet, is started. Blast wheel will fire abrasive at high velocity on the tumbling components and blast cleans them thoroughly. The arrangement of the blast wheel ensures optimum blast cleaning and maximum utilizationÃ?? of the abrasive energy. Tumbling action of the rubber belt conveyor ensures that each and every portion of the component will get exposed to the blast stream for through cleaning. After the required blasting cycle, blast wheel unit shuts off. For unloading the components from the machine, door of the machine is opened and rubber belt conveyor is made to move in reverse direction and blasted components is then get collected into the Bin/Tray.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price Range 740000.00 - 950000.00 INR/Number Product Specifications: Weight (kg) 3.5-4 Metric Ton Pressure 6-7 Bar Surface Treatment Painted Color Dark Blue Operating Type Automatic Technology Other Power Source Electricity Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Usage/Applications Casting, Forging, Sheet metal etc Power 420 Volt (v) Product Type Other Product Description Tumblast Shot Blasting Machine (Tb- 27x 36) Tumblast type machines are basically designed for batch type operation. Tumblast Machine consists of Vertical door. For loading the components, door of the machine is opened manually & components to be blasted are loaded on to the endless rubber conveyor and the door of the machine is closed. After this Blast wheel unit, which is strategically placed at the top of the Blast cabinet, is started. Blast wheel will fire abrasive at high velocity on the tumbling components and blast cleans them thoroughly. The arrangement of the blast wheel ensures optimum blast cleaning and maximum utilization of the abrasive energy. Specification: Power Required 24 HP Machine Type Shot Blasting Machine Capacity 300 Kg Per Batch Automation Grade Automatic Die Locking Force 10-20 Ton Voltage 415 V Phase 3 Phase Number Of Doors 1 Wheel Size (inch) 15.5'' X 2.5'' Drum Diameter 686 mm (Dia.) X 915 mm (W) Shot Flow Rate 180 Kg/Wheel/Min Brand Adl Blastek Conveyor Belt Rubber Belt Power Per Blast Wheel 15 HP H.P. of Blast Wheel 15 HP X 1 No. No. of Blades 8 RPM of Blast Wheel 2800 RPM Approx. Shot Velocity (Meter/Second) 70-80 Mtr/Sec Volume in CFT 5 CFT Belt Hole Size (Standard) 8 mm Type of Dust Collector Fabric Bag type Capacity of Dust Collector 2000 CFM Filter Cleaning Arrangement Auto-Shaking Mechanism
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Price Range 850000.00 - 1050000.00 INR/Number Minimum Order Quantity 1 Unit Product Specifications: Pressure 6-7 Bar Power Source Electricity Technology Other Operating Type Automatic Color Dark Blue Weight (kg) 3.5-5 Metric Ton Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Product Type Other Surface Treatment Painted Power 420 Volt (v) Usage/Applications Casting, Forging, Sheet metal etc Product Description: Swing Table type shot blast machines are designed and built asfully integrated blast cleaning systems to handle larger and/or more fragilecastings than barrel machines. They provide a cost effective solution for batch cleaning. Swing Table type Machine consists of Horizontal door with a table type work/job handling system. This table is directly mountedon the door and it rotates on its own axis, drive unit of this swing table isprovided outside the door. This table swings out as the door is opened, making the full area easily approachable for loading and unloading of the components. For loading the components, door of the machine is opened manually &components to be blasted are loaded on to the work table area and the door ofthe machine is closed. After this Blast wheel unit,which is strategically placed on the Blast cabinet, is started. Blast wheelwill fire the abrasive at high velocity on the components placed on therotating work table and blast cleans them thoroughly. Rotational mechanism oftable ensures that each and every portion of the component will get exposed tothe blast stream for through cleaning. The arrangement of the blast wheel ensures optimum blastcleaning and maximum utilization of the abrasive energy. After the required blasting cycle, blast wheel unitshuts off and door of the machine is opened manually for unloading of thecomponents.
