01. IP/OP volt.: 12-24VDC 02. IP/OP channel: 4CH 03. Output current: 8A/CH 04. Terminal blocks connection
01. IP/OP volt.: 12-24VDC 02. IP/OP channel: 4CH 03. Output current: 8A/CH 04. Both RJ45 socket connection and Terminal blocks connection
01. IP/OP volt.: 12-24VDC 02. IP/OP channel: 3CH 03. Output current: 8A/CH 04. Terminal blocks connection
01. IP/OP volt.: 12-24VDC 02. IP/OP channel: 3CH 03. Output current: 8A/CH 04. Both RJ45 sockets connection and terminal blocks connections
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
We can supply on a monthly basis around 30-50 tons per month of Ceramic CPU scrap for gold discovery and scrap motherboards and lan cards. Our prices change according to your order. For bulk order or sample order, contact us for our quote. We have in stock CPU Scrap for immediate dispatch. The available CPU scrap details are as follows - -Scrap Ceramic CPU -Scrap Ceramic CPU with Aluminum Cap -Scrap Black Plastic CPU -Scrap Plastic CPU's -Ceramic Pentium pro -CPU 486 ceramic We welcome buyers from all over the world. Contact us with your requirement. Launched Launch Date Q3'13 Processor Number E5-1620V2 For Intel Smart Cache 10 MB For Intel QPI Speed 0 GT/s Instruction Set 64-bit Instruction Set Extensions AVX Lithography 22 nm Scalability 1S Only VID Voltage Range 0.651.30V of Cores 4 of Threads 8 Processor Base Frequency 3.7 GHz Max Turbo Frequency 3.9 GHz TDP 130 W Max Memory Size (dependent on memory type) 256 GB Memory Types DDR3 800/1066/1333/1600/1866 Max of Memory Channels 4 Max Memory Bandwidth 59.7 GB/s ECC Memory Supported Yes PCI Express Revision 3.0 PCI Express Configurations x4, x8, x16 Max of PCI Express Lanes 40 We also sell the following scrap: Computer Mother Boards Computer Finger Boards Computer Memory Computer Processors Computer Power Supplies Computer Hard Disks Computer Floppy Drives Computer CD Rom Computer Cases Computer Wires Computer Keypads Computer Mouse Computer UPS or Lead batteries from UPS Cell Phone Handsets Cell Phone PCB Boards Cell Phone Batteries Lithium Cell Phone Batteries Nickel Cell Phone LCDs Cell Phone Housings Cell P If interested, please do contact with us for more details,product photos,product availability ,shipment time.
Product Description Tubular Plate Battery 2V 250AH (OPzS250-2) Specifications The OPzS battery is a traditional tubular plate flooded battery which offers 20 years design life with a cycle life of 1800 cycles at 80% Deep Of Discharge. This range is most suited for all standby power applications that require the highest levels of reliability and security. Characters 1. Use gel electrolyte, with nice performance on wide temperature range, suitable for harsh environments coperation. (-40�º C~60�º C) 2. Made by tubular positive plate materials, monthly self-discharge rateâ?¤ 1.5% 3. Excellent recover ability of Cycling and deep discharge, more than 800 times cycle life at 100% deep discharge, improve the system reliability effectively. 4. Floaing design life time up to 20 years, in the coperation of normal float charging, capacity keeps stable, attenuation rate stays low. Application Wind power system, Solar power system, Emergency lighting alarm systems, UPS(Uninterruptible power sypply) Telecommunications, Telephone exchanges control equipment, EPS instrumentation, Bank ATM System, Medical equipment, Fire and security system and so on. Capacity 77�°F(25�ºC) 100 hours rate(3.00A 1.85V) 300Ah 10 hours rate(25.0A 1.80V) 250Ah 5 hours rate(42.0A 1.80V) 210Ah 3 hours rate(62.5A 1.75V) 187Ah 1 hour rate(132.0A 1.67V) 132Ah Internal Resistance Full charged battery 77�°F(25�ºC):0.0008�© Capacity affected by Temperature (10 hour rate) 104�°F(40�ºC) 102% 77�°F(25�ºC) 100% 32�°F(0�ºC) 85% 5�°F(-15�ºC) 65% Self-Discharge 68�°F(20�ºC) Capacity after 3 month storage 90% Capacity after 6 month storage 80% Capacity after 12 month storage 60% Max discharge current77�°F(25�ºC):1250A(5S) Charge (Constant Voltage) Float:2.23 to 2.27V/77�°F/(25�ºC) Cycle:2.38 to 2.42V/77�°F/(25�ºC) Max Current:25A
Nominal Voltage 12V Discharge Temperature -15~50 Nominal Capacity (10 hour rate) 20Ah Charge Temperature 0~40 Number of Cells 6cells Storage Temperature -15~40 2. Rated Capacity at 25 (77 F) 6. Inner Resistance & Max . Discharge Current 10 hour rate (0.1C, 10.8V) 20Ah Fully Charged battery at 25 (77 F) 15m 3 hour rate (0.25C, 10.8V) 16.5Ah Max. Discharge Current 300A (5s) 1 hour rate (0.55C, 10.5V) 11.8Ah Short Circuit Current 1000A 3. Capacity affected by Temperature (10 hour rate) 7. Self-discharge at 25 (77 F) 40 (104 F) 103% Capacity after 3 month storage 91% 25 (77 F) 100% Capacity after 6 month storage 82% 0 (32 F) 85% Capacity after 9 month storage 73% -15 (5 F) 65% Capacity after 12 month storage 64% 4. Dimension and Weight 8. Constant voltage charging at 25 (77 F) Length 181mm Cyclic use 14.4~14.9V Width 77mm Maximum charging current 6A Height 167mm Temperature compensation -30mV/ Total Height 167mm Float use 13.6~13.8V Reference Weight 5.5kg Temperature compensation -20mV/
Basic Parameters Dimensions: 201 x 99 x 35 mm Weight: 333g Adapter Input: AC 100 ~ 240 V Output: DC 24V 2.65A Display mode Segment LCD with white backlight + LED in red and green Function Introduction Charge Active, pre-charge, constant current and constant voltages are the stages of charging mode. The initial charging mode depends on the battery voltage, so active and pre-charge don't happen to every batteries. For charging mode and current, please refer to the paragraphs of charging mode and charging current on page 2 & 3. Tester will stop charging if one of the conditions below was met. 1) Remaining capacity 99% & current intensity = 0 2) Remaining capacity = full charge capacity 3) Current intensity reduce to end charge current when constant voltage charge 4) Remaining capacity reach up the set value Discharge Constant current discharge for double loads Inner load: 0 ~ 1000mA, adjustable continuously via Battery Manager External load: 0mA, 500mA, 1000mA, 1500mA, 2000mA, five gears with dip switches offered Tester will stop discharging if one of the conditions below is met. 1) Remaining capacity set value 2) Voltage set value 3) Current intensity reduce to zero Remarks: Many batteries can not measure exact current intensity, which cause an else current value appears after you set a value. However, the actual discharging current is the same with your set value. Test Testing time is 12 seconds and the purpose is to check both the charging and discharging performances. After finishing test, LED flickers with green color and LCD reports the test result. Normal: Test OK Shown on LCD Abnormal: Test NG Shown on LCD Possible causes and solutions for the abnormal: 1) Cause: battery voltage is too low to discharge Solution: try to charge the battery to raise voltage 2) Cause: remaining capacity is too full to charge any more Solution: try to discharge the battery to reduce the remaining capacity 3) Bad contact of battery connecting wires 4) Damaged battery 5) Tester trouble Capacity Correction The battery capacity value in the battery management chip will different from the actual capacity after a battery goes through many recycling cycles. It will affect the use of the battery when the difference reaches a certain degree. Capacity correction is to deep discharge a battery and then fully charge, which will correct the capacity value in the battery management chip. Remarks: Discharging current can be set via Battery Manager. Deep discharge will cause a battery losing communication with tester, so battery dropping phenomenon may happen in the discharging process if the end capacity and voltage are set too low. In such a case, active charge will make the battery work again. 50% Capacity CD50%: charge firstly, and then discharge to 50% capacity DC50%: discharge firstly, and then charge to 50% capacity Online Functions Tester can be connected with master machine via a USB port. Users can monitor, control and set parameters via Battery Manager software in the master machine. Monitoring Battery information can be monitored via three windows. 1. Home screen Battery bar and brief information can be read on home screen. 2. Battery detail information window Show smart battery data in real time and the data can be saved and printed in image format. 3. Battery graph window Voltage, current and capacity are traced in curves. Control Battery Manager can control slave machine completely. Right-click menu on the battery bar includes the related commands. Attention All the functions of charge, discharge, capacity correction and 50% capacity are comply with the charging discharging conditions, which are showed on function introduction paragraph in page 4 & 5, so parameters should be set reasonably. Especially, deep discharge will cause a battery losing communication with tester. Others 1. Active cooling 2. Active batteries of zero voltage When a battery is deep discharged, the discharge protection circuit will start up and the voltage in the battery connector will become zero voltage. In this case, an appropriate voltage should be supplied to active the battery. 3. Battery identification Battery information can be read from battery management chip after establishing communication. 4. Intelligent protection Against over-current, over-voltage, over-charge, over-heat and short circuit. 5. Fan Discharging mode: fan startup Other modes: fan startup when temperature above 48 Fan stop working when temperature below 40 6. Trouble alarm LED flickers in red color and current command stops when one of the conditions below happen. 1). There is not current for around 50 seconds when charge. 2). There is not current for around 25 seconds when discharge. 3). Charging time is above 8.8 hours. 4). Discharging time is above 9.9 hours. 5). Suitable for almost all laptop batteries, above 95% Structure Accessories 1).1 * adapter 2). 1 * USB cord 3). 1 * CD 4). 13 * connectors 5). 10 * cables 6). 10 * jumpers 7). 1 * loader Standard Export Carton
Dolby AC3/DTS audio decoders Input: 2 x Optical;1 x Coaxial;1 x Audio Output: 1 x SW/CEN;1 x FR/FL;1 x SR/SL,1 x USB It is an audio converter used in public entertainment and home Convert the optical and coaxial digital audio signal from computer PC sound card, PS3, XBOX360, Blu-ray DVD players, HD set-top boxes, HD players into analog signal, decode Dolby AC3/DTS audio and output analog audio at the same time, restore the DTS/AC3 field, widely used in schools, squares, concert halls, cinemas and other public places to enjoy the effect of DTS and Dolby. The product is widely used in back-end decoding of the computer PC sound cards, XBOX360.PS3, PS2. Set-top boxes, high-definition player, DVD player, etc. Good sound quality, feature-rich, with many interfaces, plug and play. compact, portable . Interface Introduce: A. Optical input interface: Next XBOX360, PS3, PS2. Set-top boxes, DVD player, Blu-ray DVD players, HD player B. Coaxial input interface: can be connected to computer PC sound card or notebook coaxial output, high-definition players, set-top boxes, DVD player, etc. C. AUX Input Interface: Connect to any group of LPCM stereo signals (such as computer audio, MP3 / 4 player audio) D. Three output channels: connect to home theater or a 5.1-channel power amplifier (three input channels) E.USB output: Supply 5V power to 5.1 Channel Headphone. 0.5 kg.
1. Input voltage: 12-24V/DC 2. Output voltage:12-24VDC 3. Output current: 10A*1Channel 4. Dimension: L142*W45*H27 5. Dimming type: DALI/PUSH-DIM
It is not just an individual working unit to turn On/Off Switch to DC12-48V LED Light 0-100% dimmer, but also a great media to join a smart system via RS485 Modbus-RTU comm. port. It means, no matter for simple group LED lights dimming/control or for complicated smart system control, LC-01 is the best choice in market. *4-channel designed led light dimmer and controller is using pwm dimming technology to direct drive led lights, 1~5% dimming no flash concern *each channel max load current 4a (4 channels total output power 768w@48v), with Protection design against overload, short circuit and surges *independent working unit, able to extend working units in series for more channels dimming and control demand *isolate rs 485 and modbus-rtu communication protocal able to connect with hmi tft Touch panel or smart control system like system chart 4 to dim lighting range from fully off "0" to full-on "1000" for different lighting mode and environment change setting *4-channel isolate multi-function digital input able to work with existing or general power On/off switch for light on/off and 0-100% brightness dimming and to connect sensor for On-off, detain or group dimming setting *wide working voltage 12-48v dc, to ensure stable and continued electricity supply for led lights to extend the working life of led lights, industrial power supply working source is recommended *extend ports for remote control or sensor for smart control system *watchdog function supported *easy installation and set up, cost-effective, low maintenance cost, long working life of led and environment protection
Product Name: Electric Skateboard (600W) Specifications: 1) Battery capacity: 3 x 7A, 36V 2) Motor power: 600W 3) Charging time: 3 - 6hrs 4) Speed:
Artnet-dmx converter is the ethernet control system based on the artnet protocol, used to convert the artnet network date package into dmx512 date, adopting high-speed arm processor, stable and reliable working. Following art-net standard protocol, it support rj45 network interface and standard dmx512 output interface.
Ad300 decodes the input ts signal and output aes and balance analog audio, supports mpeg-2/mpeg-4 aac/aac2, mpeg-1 audio layer 1/2/3, wma9 audio decoding standards. Adopted low power consumption and high integration, ad300 decodes up to 20 channels audio in real time in 1u chassis with less than 30 watts consumption for whole equipment. Module-based design, supports hot swap, thus it is easy to maintain and upgrade, and it can join with other process modules of our company flexibly to realize multifunction and interface solution Management is based on web browser, support snmp Main features: Audio decoding compliant with the standard of mpeg-2/mpeg-4 aac/aac2, mpeg-1 audio layer 1/2/3, wma9 Supports asi, ip input Supports aes, balance analog audio output Decode up to 20 channels audio in 1u equipment Module-based design, supports hot swap, many different processing modules can be assembled in same chassis flexibly Management supports web browser. Independent management software and snmp Power consumption of whole equipment is less than 30 watts Dual power supply can switch automatically -
1.Available for encoding, and for setup of the address for each DMX512 decoder module (SC-DMX-00xH/L) of own company; 2.Available for one-time setup of different addresses for the DMX512 control system consisted of by SC-DMX-00xH/L(DMX-512 decoder module) of own company; 3.Available for transmission single and multiple channel DMX512 signal; 4.Available for scene function, and for independent setup of DMX512 Start code and value of each channel; 5.Support transmission of DMX512 testing signal by 40Hz or 20Hz; 6.Available for receiving DMX512 signal and for separate display of 512 channels and their respective Start code. Technical specifications: Brand name SC-DMX-512 Communication protocol DMX512/1990 DMX512 I/O RJ45*2 Display 16*4 large screen LCD Power supply input DC 9V Rated power
