DESCRIPTION CC-103(1K) Crystalline Waterproofing Materials is fusion resin powders which contains water-soluble crystalline mineral coating with special additive syntheses. It will have a protective coating which is firm and impact resistance after curing. CC-103(1K) is a high technology product to prevent water leakage. ADVANTAGES * Prevent the constructions aging phenomenon * Avoid the leakage and mold on the wall * Effective against negative water pressure * With good stability * Non-Toxic APPLICATION * Internal and external walls * The leakage of inner wall in basements or the protection against negative water pressure * The construction of base isolated structures * Reservoir; drinking water pool * Contaminated water pool; water storage tank PROCEDURE 1. Ensure all surfaces which CC-103(1K) will be applied are clear. 2. Mix one pail(22.5KG) of CC-103(1K) and 4.5~5.0Liter water well by construction mixer. 3. Wait for 3-5 minutes and stir before use; use finishing trowel to smoothing or apply evenly with a nap roller. 4. Use finishing trowel to smoothing after using spray machine. PACKING 22.5KG per pail. STORAGE 6 months in original container stored in dry conditions. LIMITATION The crystalline products need to be used between 4 °C ~ 32 °C when applied.
DESCRIPTION CP-310 was synthesized from imported high-technology macromolecule resin and specialized paint that is different from general acrylic resin. CP-310 is a perfect product to provide a high water-tolerant, climate-tolerant, and anti-UV ability. FEATURES * Excellent environmental water-based waterproofing paint * Water-based, Non-toxic, odorless, inflammable, and harmless * Fine adhesion, extreme toughness, high elastic, and high endurance * Hydrophilic, and may be applied on damp surface USE RoofBuilding, condominium, factory, barracks, school, garden and etc.. WallsBasement wall , exterior wall , and etcâ?¦ PREPARATION 1. (The following steps are recommended for best results) 2. New concrete must cure for a minimum of 30 days 3. All holes or cracks must be properly patched 4. All surfaces must be clean and free of dirt, dust, efflorescence and oil APPLICATION (The following steps are recommended for best results) 1. Stir well before use. Do not thin; however, if thinning is necessary, thin water at a rate of no more than 10% 2. One prime required CP-310 primer 3. Two coats are required for the best resultskeep the thickness of each coating below 1m. 4. Wait for each coating to be total dry before overlaying the next coat. The interval time between each coating is minimum of 8 hours. COVERAGE 5-gallons about 33m2 COLOR Grayã??Whiteã??ivoryã??Green DRY TIME Dries to touch in about 1-2days . Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 14-30 days. CLEAN UP 1. Clean hands and tools with soap water. 2. After 30 days or paint has fully cured, areas may be wasted using a non-abrasive, mild detergent and cellulose sponge. WARNING (Read the following carefully for your own safety) 1. Keep out of reach of children-Do not take internally. 2. May cause eye, skin and respiratory tract irritation. May be harmful if swallowed. Use only with adequate ventilation.
DESCRIPTION CC-103(2K) Crystalline Waterproofing Materials is a capillary waterproofing formulation. CC-103(2K) has high permeability which crystallize and penetrate deeply into the capillaries of the concrete. ADVANTAGES * Applied to wet surface * Transparent, non-toxic and odorless * High cohesion and effective against positive/negative water pressure well APPLICATION * The leakage of inner wall in basements or the protection against positive/negative water pressure * Prevent seepage and leakage in underground passages and tunnels * Avoid the leakage of cisterns and pools PACKING 30KG/Set A: 22.5KG in powder.+ B: 7.5KG additive. COLOR Grey and white. STORAGE 6 months in original container stored in dry conditions and under 25°C.
1,Name:construction white or clear leno tarpaulin building cover tarps with words or logo printing 2,Material:100% virgin reinforced HDPE coated with LDPE waterproof lamination with UV stabilizer 3,Color:Transparent / Clear, white, green, etc. 4,Thickness:150 micron, 200 micron 5,Weight:120gsm, 130gsm, 140gsm, 150gsm, 160gsm, 180gsm, 200gsm or customized 6,Features:Anti-UV, anti tearing, anti-aging, anti-hail, etc 7,Light Transmittance �?� 88% 8,Width:1m, 2m, 3m, 4m without jointing, other width has to be welded 9,Length:Any length customized 10,Application: Fruit trees tent cover (cherry, grape, apple, etc) Greenhouse roofing cover poultry house sides rolling curtain Home garden plant/flower protection plastic film Construction scafolding cover Main Features: 1) Anti aging, UV resistant, tear resistant, anti hail, etc 2) Large width provided. 1-4m without jointing,if over 4m, width need to be welded up to 30m 3) No limit on length 4) Customized packing accepted. 5) Free sample available.
Characters: 1.Strong decoloring-ability 2.Good adsorption 3.Higher in activity degree Applications: 1.Refining plant oils like: soyabean oil,corn oil,palm oil,coconut oil,sunflower oil,peanut oil,cotton seed oil,oliva oil,rice bran oil,caster oil,linseed oil,tung oil,rapeseed oil,etc. 2. Refining animal oils like: fish oil,lard oil,tallow oil,etc. 3. Refining industrial oils like: used lubricantsoil,motor oil,engine oil,automative oil,paraffin wax,olefin,diesel,etc.
Characters: 1.Strong decoloring-ability 2.Good adsorption 3.Higher in activity degree Applications: 1.Refining plant oils like: soyabean oil,corn oil,palm oil,coconut oil,sunflower oil,peanut oil,cotton seed oil,oliva oil,rice bran oil,caster oil,linseed oil,tung oil,rapeseed oil,etc. 2. Refining animal oils like: fish oil,lard oil,tallow oil,etc. 3. Refining industrial oils like: used lubricantsoil,motor oil,engine oil,automative oil,paraffin wax,olefin,diesel,etc.
PP non woven geotextile fabric Product Description PP non woven geotextile fabric is made from polypropylene(PP) short fiber or long fiber by nonwoven needle punched manufacturing process, pp non woven geotextile fabric has isolation, filtration, drainage, reinforcement, protection and maintence etc. function. APPLICATION : 1.Separation Geotextiles will prevent two soil layers of different particle sizes from mixing with each other , as is illustrated the image below. 2.Drainage Geotextiles will efficiently collect superfluous water from structures , such as rainwater or surplus water, from the soil and discharge it. 3.Filtration Geotextiles are an ideal interface for reverse filtration in the soil adjacent to the geotextile , in all soils water allowa fine particles to moved . Part of these particles will be halted at the filter interface; some willbe halted within the filter itself while the rest will pass into the drain. The complex needlepunched structure of the geotextile enables the retention of fine particles without reducing the permeability of drain. 4.Reinforcement Heavy geotextile can be used to reinforce earth structures by means of fill materials . THanks to their high soil fabric friction coefficient and high tensile strength, they are an ideal reinforcement solution. 5.Protection Geotextile are an ideal protection from erosion of earth embankments by wave action, currents or repeated drawdown. A layer of geotextile can be placed so as prevent leaching of fine material. They can be used for rock beaching or as mattress structure.they can even easily be placed under water. Product Features 1.High tensile strength and modulus ,low elongation, low creep and high long-term design strength. 2.Ease of Construction. 3.Cost effective. 4.Creep resistance. 5.Consistency. 6.Less differential settlement Packaging & Shipping FAQ 1. How about the delivery time? Lead time since receipt of 30% T/T deposit payment :5-15days? 2. Can you send samples to customers? Free samples could be provided , but customer need pay for the freigt cost. 3.Can you produce the product according to customers' requirements? Sure, we are professional manufacturer, OEM and ODM are both welcome.
Polypropylene woven menbrane/ fabric sheets Why use erosion control matting? This geotextile is made from, 100% mono filament polypropylene. Mono filament is the superior, erosion controlmaterial with its fishing line-like strands woven together. This provides excellent, stabilisation and reinforcement, for vegetation growth. Request a price quote How does a geotextile control erosion? Geotextiles are, ideal for, soil erosion, prevention, control/repair, and restoration. The fabric will create a solid base over the eroded soil and, allow the plants to colonize and establish the vegetation, needed to control the erosion., , , , Function: , 1.Geotextile has good air and water permeability to let water flow through it so as to effectively control sandrock running-down. 2.Geotextile has good water transmissibility, it can form drainage channels inside soil mass to drain redundant liquid and air out of the soil mass. 3.Geotextile helps to enhance the soil mass' tensile strength and non-deformability and structural stability so as to improve soil mass quality. , Features: , 1.It can effectively make the concentrated stress diffuse, transfer or decompound, and prevent the soil mass against the destruction of outside force. 2.It can prevent the mixture of sandstone, soil mass and concrete of upper and lower layers. 3.Its mesh is hard to jam by virtue of the compliancy and motility of the reticulation formed by indefinite form fibrous tissue. 4.High water permeability-it can keep good water permeability even in the pressure of soil and water. 5.Corrosion resistant-it is made from polypropylene fiber or terylene or other chemical fiber, featuring resistance to acid and alkali and oxidation, non-corroding, no worm-eaten. 6.Easy construction-low weight, easy operation, simple construction.
Hipped geomembrane for landfill closures waterproof liner 0.1mm-3mm/m2 1. Geomembrane specifications 1) Thickness : 0.15mm - 4.0mm. 2) Width : Within 8 m (1m-8m). 3) Length : 50m-100m/roll (as request). 4) Material : HDPE,( LDPE, LLDPE, PVC, EVA ). 5) Color : Black , white , red , blue , or as required. 6) Optional surface : Textued(one or two side) or smooth surface. 7) Certificate:CE/ISO9001,14001 2. HDPE geomenbrane Features Good mechanical properties, high tear strength, deformation and adaptable, puncture resistance, anti-aging, anti-ultraviolet-resistant, Anti oil and salt, pH, anti-corrosion, high temperature-resistant, non-toxic, long service life. water, drainage, seepage, the good effect of moisture, width, thickness of the full range of specifications and low cost, simple construction. 3. HDPE Geomembrane Applications 1) Environmental protection, sanitation (such as solid waste landfills, sewage treatment plants, power plants Chi-conditioning, industrial, hospital solid waste, etc.) . 2) Water (such as rivers, lakes and reservoirs of the anti-dam, plugging, reinforcement of the canal seepage, the vertical wall of the heart, slope protection, etc.). 3) Municipal Engineering (subway, on the ground floor of the building, planted roof, the roof garden of anti-seepage, sewage pipes lining, etc.). 4) Landscape (man-made lake, river, reservoir, golf courses reservoirs of the substrate, slope protection, green lawn of the waterproof moisture, etc.). 5) Petrochemical (chemical plants, oil refineries, gas storage tanks of the anti-chemical reaction tanks, sedimentation tanks of the lining, etc.). 6) Mining (washing and pool heap leaching, the ash-field, dissolved, precipitation, the yard, the tailings seepage substrates, etc.) HDPE geomembrane NO. Items Value Common Environment 1 Thickness (mm) 0.2 - 4 2 Width (m) 2.5 - 8 3 Tensile Strength(TD/MD) MPa ?7 ?¥25 4 Elongation at Break(TD/MD) % ?¥4550 5 Strength at Tear(Right-angle Tear) N/m?110 6 Carbon black content % 2.0 - 3.0 2.0 - 3.0 7 Anti-crack F20 ,1500 8 -70low temperature impact brittle prope pass 9 Oxidative Inducement Time at 200°C,m20 LDPE geomembrane NO. Items Value 1. Thickness (mm) 0.2 - 3 2. Width (m) 2.5 - 9 3. Tensile Strength(TD/MD)MPa14 4. Elongation at Break (TD/MD) 400 5. Strength at Tear(Right-angle Tear)N/m50 6. Permeability coefficient of Vapour(g.cm/cm2.s.p)
Color white or Black Characters dustproof, waterproof,air permeability,oleophobic Air Flow 300ml/cm ²/min@70mbar IP Rate IP67,IP68 ODM,OEM available Shape round sheet,square sheet,rectangle sheet,customer's design could be available Structure Adhesive backing or non-adhesive backing Application sensor,cell,automotive,LED light,power,tester,equipment outdoor electronics etc
Glazed tile roofing roll forming machine main roll forming system: Usage: in order to keep the product shape and precision, adopts welded sheet structure, motor reducer drive, chain transmission, roller was chromed which can keep the molding plate surface smooth and not easy to be marked when it is being stamped. Length of the main part: about 650014501500 Weight of main part: 3.8 tons Voltage: 380v 50hz 3 phase Roller fixer: middle plate Frame: 350 h steel welded Drive mode: chain Material of rollers:45# steel, surface hard chromium plating. Material of shafts: 45# steel Diameter of shafts: ï?80mm Number of rollers: 13 rollers Main power: 5.5kw
Core Material: PE, PP Color: black, white,grey ,orange ,blue and so on. Weight: 300g/m2,400g/m2,500g/m2 or customized Length:100M, 50M or customized Width:1.15M, 1.20M, 1M Thickness: 0.5mm-1.5mm Polyethylene polypropylene fiber waterproof membrane is one kind of multi-layer polymer waterproof membrane, its base materials are polypropylene fiber and polyethylene, adding some chemical auxiliaries, totally four layers, protective layer, anti-aging layer, waterproof layer, adhesive layer. Product Features: 1) Non-toxic, no smell, no pollution. 2) Anti-aging, anti-oxidant, corrosion resistant. 3) Good flexibility, tensile strength and anti-perforation well. 4) It can be the same life time with buildings. 5) Easy operation. Application: 1) Roofs, underground, tunnel. 2) Industrial and civil building waterproof. 3) Geo-synthetic liner for swimming pool, channels, irrigation system 4) Especially for projects with high requirements in durability, anti-corrosion and deformation. Application method: 1. The application is simple and of no-pollution. It is mainly used in the middle of building for waterproofing. On this layer, other layers of protection and decoration are needed. 2. When application, pour the adhesive materials homogeneously on the smooth roof deck, then roll the membrane to make it fully adhered to the deck. 3.The adhesive materials are usually made from water, cement and other building glue at the volume rate of 3:6:1.
Simcon-WPR 1000 Water Proofing & Reducing Type : Pce Based Water Reducing Superplasticizing Set Retarding Concrete Admixture ALL IN ONE TYPE ADMIXTURE DESCRIPTION Simcon-WPR 1000 Imparts high workability and gives workability retention. USES Simcon-WPR 1000 a superplasticizer for free flowing con- crete in floor, slabs, foundations, walls, plasters slender components with dense reinforcement, walls, columns, pavements and other structural and non structural elements. It is specially recommended for the following types of con- crete: Ready mix concrete Pre cast concrete Site batched concrete CHARACTERISTICS / ADVANTAGES Simcon-WPR 1000 produces a more uniformly cohes-ive high quality free flowing concrete. It has following advantages : Improved water reduction. Improved strength and density Improved consistence retention Improved durability Improved water tightness/ water proofed concrete PRODUCT INFORMATION Improved surface finish Improved cohesion properties Suitable for hot weather conditions Water reduction up to 15-20 % depending on dosage* * This will depend on dosage and mix design Composition Modified Napthalene Formaldehyde Sulphonate Packaging 1KG,5KG,10KG,20KG. Appearance / Colour Dark Brown Liquid/Coffee,Honey Colour Colour Shelf life 24 months from date of production if stored properly in undamaged un- opened, original sealed packaging. Storage conditions Store in dry conditions at temperatures between +10C and +40C. Protect from direct sunlight and frost. Density ~1.17 kg/l at 25C pH-Value 6 Application Dosage : 250ML Per 50KG Cement Bag Compatibility Simcon-WPR 1000 may be combined with many other Simcon�® products. Important: Always conduct trials before combining products in specific mixes and combinations. Compatible with all types of cement and cemen- titious material APPROVALS / CERTIFICATES International ISO Certified - Dubai Acccreditation Center ISO 9001: 2015 Certified Bangladesh Department Of Environment Certified Bangladesh Fire Service & Civil Defense Certified Bangladesh Fire Service & Civil Defense Certified Our Products Are Also Tested By Buet
Width : 2 mtr-8 mtr With Additive UV Application : -Fish Pond -Shrimp Pond -Landfill -Road Construction -Salt Pond -Waste Container -etc
Geomembrane is a kind of waterproof impermeable liner for containment,ponds, and fluid/gas leak control ,antiseepage control projects. The geomembrane liners are made of virgin polyethylene resin by the film blowing or calendering process. All the PE resin is 100%virgin material from Saudi Arabia, Qatar etc famous manufacturer with masterbatch from Cabot company. HDPE lldpe geomembrane Thickness 0.3-3mm width 1-8m length 50m 100m
Geosino with Over 20 years of experience for Geomembrane manufacturing , HDPE/LLDPE smooth/ textured geotechnical anti-seepage membrane is manufactured by Italian automatic geotechnical production equipment, uniform plasticization and co-extrusion. It is produced with high-quality special polyethylene virgin resin and imported carbon black from Cabot. Geosino Geomembrane products protect the earth from waste and pollutants, protect investment, and ensure the integrity and sustainability of important infrastructure in harsh environments. We have expertise in all geosynthetics and are committed to continuous innovation. Our vision is to promote the development of geosynthetics industry, improve industry standards and create more reliable, stronger, pollution-resistant and ubiquitous products. Geosino Geomembranes are used in a variety of applications, such as: Water reservoirs Landfills lining and capping Irrigation canals Mining Highways, dams, lake banks Aquaculture Pond lining Lining of metal tanks
We manufacture and export HDPE Geomembrane Pond Liner.HDPE Geomembrane is a kind of pond liner created from high-density polyethylene. It is invulnerable to punctures, tears, and snags, making it an excellent option for areas up to 30 feet in diameter ponds. HDPE pond liners are also light in weight and very comfortable to haul, so you can easily shift them around as required. Are you looking for a HDPE Geomembrane Manufacturer in India? Look no further! Contact Mahira Polyglobal today. Get in touch with us:
We manufacture and export HDPE Geomembrane Pond Liners. An HDPE Geomembrane pond liner is a durable and flexible plastic liner made from high-density polyethylene (HDPE) used for lining ponds, lakes, and other water containment applications. It provides an impermeable barrier to water, preventing leaks and seepage, thus ensuring water conservation and environmental protection. Known for its high chemical resistance, UV stability, and longevity, HDPE Geomembrane pond liners are ideal for both residential and industrial use, offering a reliable solution for creating water-tight ponds and reservoirs. Our HDPE Geomembrane Pond Liners are available in different sizes. Are you looking for an HDPE Geomembrane Supplier in India? Get in touch with us
Smooth HDPE geomembrane liner, also known as high density polyethylene geomembrane liner, is the very low permeability synthetic membrane liner or barrier used with any geotechnical engineering related material so as to control fluid or gas migration in a human-made project, structure, or system. GEOSINCERE brand smooth HDPE geomembrane liner is made from finest quality virgin high density polyethylene (HDPE) with specially formulated, combined with specified quantity carbon black, antioxidant, anti-aging agent and UV resistance components, which makes our geomembrane product with excellent resistance to UV radiation and is suitable for exposed conditions.
Redispersible polymer powder is free flowing white or light yellow powder obtained through the spray-drying of aqueous emulsions, which is suitable for the production of various dry mortar. Redispersible Polymer Powder is re-emulsified with water and has the same properties as the original emulsion, that is a film can be formed after water evaporation. This film has high toughness, weather resistance and adhesion to a substrate. In addition, the latex powder with hydrophobic properties can improve the waterproof performance of the waterproof mortar.Water-reducing properties is mainly used for self-leveling.
