Lc 300 is a designed specifically for stains on granite
Surfaces arising out of contamination during production
Or due to storage. It is very effective for stains on granite
Surfaces due to poor quality water, inproper storage &
Soil contamination. It is an acid based special blend of
Selected penetrants, emulsifiers, dispersant & solvent
Carriers designed to effectively penetrate, react, dissolve
& remove the stains from the surfaces as well as deeper
Into the granite structure without affecting the surface.
Application
Make sure that the granite surfaces are free from dust, soil & dirt. Apply lc 300 on
The pre-treated surface by brushing to leave a thin uniform film on the whole
Surface. Do not leave any surface untreated. Wait until 15-30 minutes or more until
The stains start dispersing. Rinse and wipe clean the whole surface with demin
Water. For deeper & thicker stains, repeat the process. May not be suitable for
Certain types of granite & marble. Always make a test sample before final
Application.
Handling & precaution
Avoid contact with eyes, skin and clothing. In case of contact, immediately wash
With plenty of water. Harmful if swallowed.
Packaging
Available in pail of 20 lt.. Can also be custom packaged
Kb 208 can be used to remove stains from hard surfaces
Including metallic and non-metallic surfaces like glass, ceramic,
Melamine, etc. The key to an effective cleaning depend on proper
Dilution & soaking time. It’s food-grade quality allows its use in
Places where cleaned surfaces may have direct contact with food.
Kb 208 is designed specially for use in places where the use of
Acidic products are not recommended. It’s strong disinfectant
Function kills most common microbes & disease causing bacteria.
Application
Kb 208 must be diluted with water for soaking, dipping etc. May also be used by
Brushing & scrapping. Dilution depend on soak time, for faster action use lower
Dilution ratio that is higher concentration. May be diluted up to 500 times or more. It
Has disinfectant function.
Dosage
Add about 100 gm/100 ml of kb 208 to about 100 lt. Of water or as required for
Soaking and dipping. Use higher concentration for faster action and tougher stains.
Agitation gives better result. Re-use solution until turbidity is high. Required to
Repeat the process if necessary. When the cleaning process is complete, flush with
Clean water. Use concentrated product for manual cleaning
Handling & precaution
This product is alkaline and should be handled with care to prevent personal injury.
Avoid prolonged skin contact and breathing of the fumes. Refer to material safety
Data sheet for more specific procedures and directions. Discoloration may
Result when contact with colored clothing.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Cleaning vinyl surfaces from dirt, grease, oil, and dust. Suitable for carpet cleaning vinyl flooring and other vinyl surfaces. Safe to use on metal surfaces such as stainless steelm aluminum, copper, brass.
Kb 217 is a special water based carpet cleaner to
Penetrate, emulsify and disperse oil, grease, dirt and stains on
Fibers of synthetic carpets. Ideal for cleaning synthetic carpets
Normally used on floors of office buildings, hotels, hospitals &
Other public places. This formulation does no have any adverse
Effect on painted surfaces including walls, wood and also metals
Like stainless steel, aluminum, copper and brass. The room is
Filled with a refreshing fragrance from kb 217 after the cleaning
Work.
Application
Use diluted kb 217 ( 1 : 5 up to 1 : 20 with clean water ) with standard carpet
Cleaning equipment like mopping machine & wet vacuum cleaner. Apply & spread
The solution of kb 217 to the carpet surface and allow a soaking time of 2 – 10
Minutes before scrubbing rinsing & final mopping. The wet carpet should be
Properly mopped with standard equipment & procedure until dry.
Always make a test patch to confirm color fastness & soaking
Time.
Kb 217 can also be filled in directly into the detergent container provided with
Certain carpet cleaning equipment which has a facility for it.
Dosage
Dilute with water depending on the cleaning work & stain. Can be diluted up to 20
Times. Direct applications of the undiluted product may be required on highly
Stained areas
Handling & precaution
Avoid spills on eyes. Should avoid prolonged unnecessary contact with skin. May
Irritate when exposed for a longer period on certain sensitive skin. Harmful if
Swallowed. Keep away from children. Keep container capped in a cool dry place
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 120 is a product which effectively prevents scale and
Corrosion in cooling towers having very soft waters which
Are more corrosive, have a rysnar index over 7 and
Calcium 25 – 75 ppm in the make-up water. It is an
Excellent dispersant for calcium phosphate, iron oxides
And clay. This product is used where heavy metals and
Zinc is not allowed in effluent waters. Lc 120 is a
Hydroxy-phosphonoacetic acid with polymers and copolymers
To control scaling. It also has inorganic
Phosphate and sodium tolytriazole to prevent corrosion
And pitting of all metal surfaces.
Application
Injected directly into the circulating pipe upstream from the condenser.
Cycles of concentration will vary from 5 – 20 as a probable upper limit. For
Higher limits consult our laboratory.
Dosage
Feed lc 120 from a chemical mix tank or directly from the drum by means
Of a proportioning pump at the rate of 0.5 pound / 1, 000 gallons of make-up
Water. Adjust the dosage to maintain 5 – 10 ppm of orthophosphate in the
Circulating water. A ph of 8.0 – 8.5 must be maintained.
Handling & precaution
Protective clothing and eye protection should be worn. In case of skin
Contact, immediately flush thoroughly with plenty of clean water. In case of
Eye contact, flush with copious of amounts of water for 15 minutes and
Obtain immediate medical attention.
Packaging
Available in pail of 20 lt.. Can also be custom packaged
Lc 238 is designed specially for use in systems where the use
Of concentrated acidic or concentrated alkaline descalers are
Not recommended. This product is specially formulated for
Specific cleaning and descaling purposes for sensitive system.
Lc 238 may be re-circulated by means of a high volume pump
For the removal of scale. Lc 238 can be used safely on to
Copper & brass surfaces besides being very effective in steel
System.
This product contains organic poly acrylic & polymer
Compound.
Application
Lc 238 may be soaked overnight and re-circulated. When scale is
Present, the tubes should first scraped out to remove as much as possible
And then flushed out with a hose.
Dosage
Circulate an appropriate concentrated solution based on the scale and
Corrosion. For storing / stand by system use lc 253 or lc 252. For more
Detail and specific method and concentration, please consult lifechem
Technical services.
Handling & precaution
This product ph is between 4.0 – 9.0 and should be handled with care to
Prevent personal injury. Protective clothing, gloves and eye protection
Should be worn. In case of skin contact, immediately flush thoroughly with
Plenty of clean water. In case of eye contact, flush with copious amounts
Of water for 15 minutes and consult a physician. Refer to material safety
Data sheet for more specific procedures and directions.
Packaging
Available in pail of 20 lt.. Can also be custom packaged
Lc 239 is a very strong descaler for destroying the most
Difficult scales. It effectively removes difficult scales, rust,
Oxides of metals, silica scale and hard soil from metal and
Other surfaces. It’s dissolving action is quick and thorough.
Most cost effective descaler when combined with lc 230,
Lc 233, lc 232 and lc 231. Do not use on materials like
Glazed tiles and glass. Must be used after dilution only.
Application
Dilute and blend with other descalers as necessary before dipping, brushing or
Spraying on surfaces. Clean surface free from excess rust, soil and dirt. Apply lc
239. Allow to stand for 10-20 minutes, then flush off with water. Surface may
Require repainting if necessary. Recommended to use lc 240 for neutralization
And lc 252 for passivating the native surface on ferrous metals. Avoid contact
With unwanted surfaces.
Dosage
For descaling purposes, dilute one part lc 239 with up to 20-100 parts of water
Depending on the type and thickness of scale and method of application. Allow to
Stand / circulate for several hours or as necessary. Flush with water until all the
Scale is removed. Repeat if scale is still present, check ph during application for
Control. Contact field chemist for further information. Do not use above 2% with
Non-chemical pumps for circulation
Handling & precaution
Strongly acidic. Irritating to eyes and skin. After contact with skin wash
Immediately with plenty of water. In case of eye contact irrigate thoroughly with
Water for at least 15 minutes. Seek medical advice. Avoid direct contact with
Glass, tiles and other such surfaces. Use adequate protective measures during
Use.
Packaging
Available in pail of 20 lt. Can also be custom packaged.
Lc 240 is a highly alkaline concentrated product designed
For neutralizing the metal surfaces that is susceptible to
Corrosion. Lc 240 consists of a blend of soluble carbonate,
Hydroxide and corrosion inhibitors. It is designed to control
Corrosion and neutralize any acid left from “acid cleaning”
Processes. It contains no chromate or heavy metals. It is
Food grade, user & machine friendly and environmentally
Safe. Neutralized mixtures can safely be disposed into
Sewers. [ p – powder / l – liquid ]
Application
Can be added directly into the liquid volume to give a 1% to 5% solution or add till
Ph value is between 6 - 8, which then may be used for neutralization & protection.
For offline storing purposes a 0.5% solution may be quite effective. The surface to
Be neutralized or get protection must receive a minimum of 5-10 minute contact
Time.
Dosage
Dosage is calculated depending on the circulating or storing volume and the time
Of contact. A diluted solution of 0.5% up to 5% is recommended. Use concentrated
Solution for less contact time & higher initial conditions, where as a 0.5% solution
May be used for storing. Ensure ph value between 6 – 8 before disposal.
Handling & precaution
This product is quite alkaline and should be handled with care to prevent personal
Injury. Protective clothing and eye protection should be provided and worn. In case
Of skin contact, immediately flush thoroughly with plenty of clean water. In case of
Eye contact, flush with copious of amounts of water for 15 minutes and obtain
Immediate medical attention.
Packaging
Available in pail of 20 lt. Can also be custom packaged.
Lc 214 is a special blend of penetrants, chlorinated
Solvents, surfactants and emulsifiers designed to easily
And quickly strip paint and varnish from metals, concrete,
Brick, wood and most hard surfaces.
The deep penetrating action of lc 214 soften though
Paint and removes it without scraping.
Lc 214 is homogeneous which adheres to vertical and
Inverted surfaces and activate paint coating quickly.
Application
Brush, wipe or apply a heavy coat of lc 214 on the area to be
Treated. For the reaction to be completed, allow lc 214 to
Remain until old paint bubbles or wrinkles. Flush with water or
Remove with scrapper. More than one application may be
Required for areas of very heavy paint build-up.
Dosage
One ( 1 ) liter of lc 214 can be used over an area of 3 – 5 m2
.
Handling & precaution
Avoid contact with skin. In case of contact, wash affected areas
With water.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 253 is an alkaline concentrated food grade product
Designed for “passivating“ as well as neutralizing the
Metal surfaces that is succeptable to corrosion. Lc 253
Is also an alkaline formulation of phosphate, polymeric
Dispersants and corrosion inhibitors. It is designed to
Control corrosion and neutralize any acidic left over from
Acid cleaning processes. It contains no chromate or
Heavy metals.
Application
Can be added directly into the raw water to give a 2% to 10% solution,
Which then may be used for “passivating”, “neutralization” & “protection”.
For offline storing purposes a 0.5% solution may be quite effective. The
Surface to be passivated, neutralized or get protection must receive a
Minimum of 15-30 minute contact time.
Dosage
Dosage is calculated depending on the circulating or storing volume and
The time of contact. A diluted solution of 0.5% up to 10% is recommended.
Use concentrated solution for less contact time & higher initial conditions,
Where as a 0.5% solution may be used for storing.
Handling & precaution
This product is quite alkaline and should be handled with care to prevent
Personal injury. Protective clothing and eye protection should be provided
And worn. In case of skin contact, immediately flush thoroughly with plenty
Of clean water. In case of eye contact, flush with copious of amounts of
Water for 15 minutes and obtain immediate medical attention.
Packaging
Available in pail of 20 lt.. Can also be custom packaged
Lc 252 is designed to be used for “passivating” open &
Closed loop systems to prevent corrosion. It is a liquid blend
Of nitrite and other corrosion preventives which protects not
Only steel surfaces but also copper and other metal as well.
The high concentration makes it a cost effective nitrite based
Passivating agent with the added advantage of being multimetal
Compatibility and thus do not require separation of
Non-ferrous parts from a system during passivation.
Application
Normally injected into the system that is previously filled with standard industrial
Grade water and circulated continuously under required pressure for about 1-2
Hours with hourly monitoring of the nitrite concention. A higher temperature help to
Accelerate the passivating process and therefore reduce operation time. An
Appropriate temperature suitable to the system and available resources is choosen
Between 35 – 950c
Dosage
Initial : 1 : 400 is suitable in most cases of passivation processes operating at
Optimum temperature between 50 – 700c. Depending on the quality of water used
Some adjustment in the amount may be required to maintain the ph of the solution.
An increase in concentration of lc 252 is necessary in badly soiled systems.
Additional amount of lc 252 may be required to be added during the circulation for
The passivation process in order to maintain the required control parameters while
Monitoring.
Handling & precaution
Avoid contact with acid, ammonium salts and activated carbon. No respiratory
Protection. Is required, however, maintain adequate ventilation. Use rubber gloves
And safety goggles when handling.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 271 is a strong solvent based degreaser and
Decarboniser for the rapid removal of oil, grease, paint,
Adhesives and waxes from metal components and
Machinery. The mechanism of cleaning involves a quick
Penetration of lc 271 to soften polymerized oils
Associated with the carbon deposit. Then the deposit is
Loosened and easily dispersed into the solvent. The
Powerful solvents act quickly to break the bond between
The deposits and the metal surface. Lc 271 is safe to
Use on ferrous and non-ferrous metals, concrete and
Ceramics.
Application
Ideal to use in metal dip tanks, spraying, wiping etc. Item to be descaled,
Decarbonised or degreased should be immersed below the surface. Loose
Soiling should be removed prior to immersion. After removal allow them to
Drain for 10 minutes. Then, rinse with low pressure water. Keep container
Covered for control evaporation.
Handling & precaution
Harmful if inhaled. May cause burns to eyes and skin. In case of contact
With skin, wash immediately with plenty of water. Ensure adequate
Ventilation at the point of use. If swallowed, seek medical attention.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 272 is a water based concentrated degreaser to
Penetrate, emulsify and disperse oil, grease, dirt, soot,
Grime and other types of soils from a variety of hard
Surfaces. Safe for all types of metal surfaces.
Specially designed for use in ovens, grills, chimneys, exitways,
Smoke escapes, air vents & other such places
Where thick deposits of oil/grease with soot / carbon is
Common.
Application
Allow soaking time for effectiveness. Apply a thin layer by spraying or
Brushing, then leave for soaking. Brush and scrap gently to remove any hard
Soils if required then flush with water.
Dosage
Dilute with ratio of 1 : 5 with water depending on the dirt thickness. Use
Concentrated product or lower dilution for tougher stains. Dilute upto 50 times
For regular cleaning work.
Handling & precaution
Avoid spills on eyes. Should avoid unnecessary contact with skin. Can
Irritate when exposed for a longer period. Harmful if swallowed.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
RXSOL MOYA OIL is effective and economical emulsifier. Safe to use on most metal surfaces, painted and coated surfaces and also used as a multipurpose degreaser in extremely hard cleaning conditions. Degreaser Moya oil Specification: Colour Redish Yellow appearance homogeneous clear. Odour- Citrus PH value- 8.50 - 9.50, Viscosity- Ford cup B-4-12 seconds at 22 Deg.c Specific Gravity - 1.042-055. Non flammable, Non Toxic, Non Caustic, Non Explosive and causes no pollution. Packing Size: 25.00 Ltr. Application: RXSOL-20-2023 is applied by Spraying , Brushing, Soaking, Dipping , Rubbing, or Mopping Spraying is used for cold cleaning interiors of oil storage tanks or where surfaces to becleaning interior or oil storage tanks or where surfaces to be cleaned are irregular. After spraying RXSOL-20-2023 should be allowed to remain for 10 to 20 minutes before rinsing. If dry surfaces is not required it is necessary to rinse with water .Brushing and mopping is used with RXSOL-20-2023 for removing oil from decks piers and other large areas . Dipping & soaking in unheated RXSOL-20-2023 is the most economical way of cleaning small or large parts.Rubbing with a soft cloth or sponge soaked with RXSOL-20-2023 is an easy and quick method of cleaning larger parts and painted surface. Steam cleaning can be speeded up by spraying RXSOL-20-2023 a few minutes prior to steam lancing. Dose: Ready to use for tank cleaning or general decreasing.
Its typical use as a tank cleaner or for general decreasing, cleaning and gs freeing for double bottom tanks, wing tanks, pipe lines, fuel oil tanks This can be beneficial as part of the initial cleaning process after the carriage of Lube oils and Lube oil additives. As soon as the tank in question has been checked empty by the attending surveyor, RXSOL-20-2054-025 Plus should be sprayed over all surfaces which are safely reachable. irst of all drain off any remaining oil from Heat Exchanger. 2) Connect the discharge side of a portable pump to the lower heat exchanger connection & the suction Side of the pump to the bottom outlet of a 200 liter drum. 3) Complete the circuit by connecting the upper connection on the heat exchanger to the top of the drum. 4) Maintain the bath temperature between 60-80 0 C throughout the cleaning operation. If it is not possible to heat, the operation will need to be extended. It is cost effective, easy to apply and use. High emulsification on mineral oils and petroleum based chemicals. Safe to use on most metal surfaces
White powder, surface density: 0.35-0.9/cm3, melting point: 622¡ãc, free solube in water, aqueous solution appears acid. It is a kind of inorganic surface active agent.
25 kg pp bag, 21mt/20fcl
2458 Water Treatment Chemicals Suppliers
Short on time? Let Water Treatment Chemicals sellers contact you.
