Lc 126 condenser water treatment does not use sodium
Chromate, zinc or other toxic chemicals in its composition. It
Eliminates the serious pollution problems usually associated
With the use of such chemicals for corrosion and scale
Control in cooling system. It protects medium size cooling
Towers against scale, sludge and corrosion. Lc 126
Contains a special anti-foulant additive to reduce
Accumulations of mud and silt in condenser tubes. Ideal for
Average towers with 75 to 500 ton capacity.
Application
Formulated for use in open re-circulating cooling water systems found in air
Conditioning and process operations. Apply manually, directly to the cooling
Tower basin.
Dosage
Initial dosage : add 1 gallon of lc 126 for every 500 gallons of system
Capacity.
Maintenance dosage : add 1 gallon of lc 126 for every 1, 000 gallons of
System water lost to bleed off from the cooling tower system
Handling & precaution
Slightly alkaline aqueous solution. Keep out of reach of children. Refer to
Material safety data sheet for more specific procedures and directions.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 141 is single product treatment designed to prevent
Scale deposits and corrosion to ferrous and non-ferrous
Surfaces in hot water heating systems and chilled closed
Loops. It passivates the surfaces and forms a barrier layer to
Inhibit corrosion. It is a synergistic combination of
Phosphonates, polymers and phosphate.
Application
Easily feed/injected directly into the system by means of a chemical by
Pass feeder.
Dosage
Initial treatment is 1 gallon per 1, 000 gallons of water in the system. There
After add lc 141 to maintain a level of 25-35 ppm (mg/l) of
Orthophosphate.
Handling & precaution
It is highly alkaline and should be handled with care to prevent personal
Injury. Protective clothing and eye protection should be provided and worn.
In case of skin contact , immediately flush thoroughly with plenty of clean
Water. In case of eye contact, flush with copious amounts of water for 15
Minutes and obtain immediate medical attention.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 143 is specially formulated for use in systems that are
Constantly exposed to air, such as vented air to pressurized
Systems providing corrosion protection even in systems that
Are not tight. It reduces maintenance costs by keeping
Exchangers, air handling units and zone valves free of
Corrosion clogs. It also reduces corrosion insulation and
System damage. Lc 143 contains boron nitrate that protects
Against oxygen and acid attack, works well in any closed
System. Recommended for any hot water boiler or recirculating
Or closed loop system.
Application
Can be added to a system either manually or with a pot feeder. If the
Treatment dosage is less that the capacity of feeder, fill up the feeder with
Tap water to prevent air on treatment. Not to be used in electric
Steam boilers.
Dosage
For chilled water circulating system : for initial or maintenance treatment,
Add 1 gallon of lc 143 for each 200 gallons of chilled water. The treatment
Level is easily tested with the drop titration nitrite test kit.
Handling & precaution
Irritant. Avoid contact with eyes. Avoid repeated or prolonged contact with
Skin. If contact occurs, flush with water. If eye contact occurs, flush with
Water for 15 minutes. Seek medical attention. Keep out of reach of
Children. Refer to material safety data sheet for more specific procedures.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 144 is formulated to prevent and reduce scale,
Rust, corrosion and sludge in generator system. It is
The most effective coolant for generator and other
High temperature systems. Lc 144 is a special blend
Of selective glycols, anti-corrosion additives and
Sludge conditioners that provide smooth running of
The systems.
Application
Lc 144 is widely used in power plants, generator system, etc... Found in
Marines, aviations, industries, automotives, industries, hospitals, etc.
Benefits
? excellent protection
? no more severe
Damages
? non-flammable
? non-polluting
? non-corrosive
? non-toxic
? completely safe to
Use
? reduces costly
Maintenance
Dosages
1. Check incoming water source for total hardness and chloride.
2. Recommended total hardness below 30 ppm and chloride below 50
Ppm.
3. Lc 144 can be diluted at a ratio of 1:1, 1:5, 1;10, 1:32 with deionised
Water (recommended).
4. Repeat application monthly or quarterly depending on application.
Flush if colour changes or becomes cloudy.
Handling & precaution
For professional use only. To be used in well ventilated environment. In
Case of contact with eyes, rinse thoroughly with water and seek medical
Advice immediately. If swallowed, take plenty of water and seek medical
Advice immediately. Avoid prolonged contact with skin. Put on gloves for
Sensitive skin. Keep out of reach of children. Additional information may
Be obtained from material safety data sheet (msds).
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
Lc 235 is designed specially for use in systems where
The use of acidic descalers are not recommended. Lc
235 may be re-circulated by means of a high volume
Pump for the removal of scale. Lc 235 can be used
Safely on to copper & brass surfaces besides being very
Effective in steel system.
Application
Lc 235 may be soaked overnight and re-circulated. When scale is present,
The tubes should first scraped out to remove as much as possible and then
Flushed out with a hose.
Dosage
Circulate a 10% solution (10 gallons of lc 235 for every 100 gallons of
Water.) for a period of four to six hours depending on the scale thickness.
Solution may be heated for effectiveness by steaming. The system should
Then be drained and inspected. If more scale remains, repeat the process.
When the cleaning process is complete, flush with clean water and place it
Back in service. For storing / stand by system use lc 253 or lc 252.
Handling & precaution
This product is alkaline and should be handled with care to prevent personal
Injury. Protective clothing, gloves and eye protection should be worn. In case
Of skin contact, immediately flush thoroughly with plenty of clean water. In
Case of eye contact, flush with copious amounts of water for 15 minutes and
Consult a physician. Refer to material safety data sheet for more specific
Procedures and directions.
Packaging
Available in pail of 20 lt..
Can also be custom packaged.
2458 Water Treatment Chemicals Suppliers
Short on time? Let Water Treatment Chemicals sellers contact you.
Lifechem lc 306 is a solvent based wet look coating for all types
Of hard and porous surfaces including granite, marble & sand
Stone. Lc 306 penetrates into the tiny pores of the surface
Structure and the minute crevices helped by the selected
Penetrants. The volatile solvents evaporates to leave an inert,
Transparent residue that makes the wet look. The surface is
Shining and polish-able, washable and ready after at least 48
Hours. Lc 306 is comprised of volatile hc solvents, penetrants
And levelling agents designed to provide excellent penetration
And wet look. Lc 306 is ideal for providing and inert coat on
Porous materials like granite, marbles, tiles and such surfaces
Including walls, floors, desks, fixtures, woodwork and even
Paper & paper based products.
Application
Applied by spray, mop, brush wipe, dip after mixing the catalyst in proper
Proportional. Leave a thick coating and let it dry for at least 48 hours. Re-apply
For thicker coat. Available for coating floors, walls, desks, fixtures, wood work.
Special use for granite, marble and porous tiled surfaces of various colours and
Types. If there is excess localised deposition, then re-apply to remove and even
The surface. Apply uniformly to avoid accumulation.
Handling & precaution
Avoid spills on eyes. Should avoid unnecessary contact with skin. Can irritate
When exposed for a longer period. Harmful is swallowed. Do not inhale the
Vapours for long period. Highly flammable, do not bring near naked
Flame. Keep in cool place. Use in a well ventilated place/room.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 122 is an effective wide band micro-biocide designed
for use in algae and bacteria control. It does not cause
foaming and is not lost by evaporation from the system.
It is a concentrated blend of organo-sulfur compounds,
which should be added only after proper dilution by slug
feeding.
Application:
Use to control algae and bacteria in re-circulating commercial and industrial
water cooling towers. Prior to its use, systems be cleaned to remove algae
growth, microbiological slime and other deposits.
Dosage:
Initial slug additions of LC 122 per 1,000 gallons of water should be
employed every 1 - 5 days or as needed. The frequency of addition
depends upon the relative amount of bleed-off and the severity of the
microbiological problem. Slug additions should be made in the sump of the
cooling tower. During very hot weather, greater frequency or higher dosage
may be required to increase its effectiveness.
Handling & Precaution:
It is a very strong alkaline treatment and may cause eye damage and skin
irritation. Do not get in eyes, skin or on clothing. Wear goggles or face shield
and rubber gloves when handling. Avoid contamination of food. Harmful or
fatal if swallowed. In case of skin contact wash with plenty of soap and
water. Remove contaminated clothing and wash before reuse. If product
gets in the eyes, flush immediately with copious amount of clean cool water
for at least 15 minutes. If swallowed, call physician. Do not induce vomiting
or give anything by mouth to an unconscious person.
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
LC 123 is specially formulated for large installations high
hardness water. It is developed for effective, economical
cooling water treatment at hospitals, hotels, large apartment
houses, office buildings and other industrial and institutional
cooling installations with high hardness make-up water. It
contains no phosphates, chromate, zinc, or other chemicals
that cause pollution problem. Helps control mineral
deposits, sludge and surface pitting and does not stain
automobiles or buildings.
Application
Use a reliable automatic proportioner with timer for controlled dosage.
Follow instructions for calculated bleed of rate and recommended daily
maintenance treatment as suggested by the Field Chemist Personnel. The
dosage and treatment program depend on size of installation and water
hardness (ppm).
Dosage
Initial treatment : Add 1 gallon of LC 123 per 2,000 gallons of recirculating
water. Maintenance treatment as per size of installation &
hardness (consult our Technician)
Handling & Precaution
Wear protective clothing and eye protection should be provided and worn.
In case of skin contact, immediately flush thoroughly with plenty of clean
water. In case of eye contact, flush with copious of amounts of water for 15
minutes and obtain immediate medical attention. Refer to MSDS for more
specific directions.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 124 is an effective chlorine based designed for use in
algae and bacteria control. It does not cause foaming. It
is a concentrated blend of organo-chloro compounds
which should be added only by slug feeding.
Application:
Use to control algae and bacteria in re-circulating commercial and industrial
water cooling towers. Prior to its use, it is advisable that systems be cleaned
to remove slime and other deposits.
Dosage:
An initial slug addition of 1 gallon of LC 124 per 2,000 gallons of water
should be employed every 1-4 days or as needed. The frequency of
addition depends upon the relative amount of bleed-off and the severity of
the microbiological problem. Slug additions should be made in the sump of
the cooling tower. During very hot weather, greater frequency or higher
dosage may be required to increase its effectiveness.
Handling & Precaution:
It is a very strong treatment and may cause eye damage, mucous attack
and skin irritation. Do not inhale, get in eyes, skin or on clothing. Wear
goggles or face shield and rubber gloves when handling. Avoid
contamination of food. Harmful or fatal if swallowed. In case of skin contact,
wash with plenty of soap and water. Remove contaminated clothing and
wash before reuse. If product gets in the eyes, flush immediately with
copious amount of clean cool water for at least 15 minutes. If swallowed,
call physician. Do not induce vomiting or give anything by mouth to an
unconscious person.
Packaging:
Available in pail of 20 lt.. Can also becustom packaged.
LC 255 is a versatile and highly effective rust
preventative for use on unpainted metals during outdoor
storage or overseas shipping. LC 255 protects metal
with heavy waxy film. It does not require any surface
cleaning or preparation and covers the metal like a paint,
but easily removable.
LC 255 provides protection for storage of metal,
equipment, tools, tanks, structures, machinery, castings,
fittings, valves, doors, frames, fixtures, jigs, etc.
Application:
LC 255 can be applied by spraying, brushing or dipping. It is
recommended to apply by dipping in a tank with water draining
facilities which ensures maximum coverage, penetration and
cost effectiveness. LC 255 absorbs water and moisture while
lubricating plated surfaces and bare metals such as steel, iron,
alumunium, copper, brass and lead.
Handling & Precaution:
Avoid contact with eyes and skin. In the case of contact with
eyes, wash immediately with plenty of water. Seek medical
advice. If ingested, do not induce vomiting, seek medical
attention.
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
KB 201 is a powerful porcelain cleaner for brightening
& cleaning porcelain surfaces. It contains complexing
agent, sequestering agent, scale remover, wetting
agent and specialized blooming remover. It is a
specialized product and requires careful application
methods. WRONG & UNWANTED APPLICATIONS
NOT PRESCRIBED, MAY CAUSE UNEXPECTED
RESULTS & DAMAGE. Must be diluted before use.
Never use on glazed surfaces.
Application:
Pour diluted KB 201 on the surface to be cleaned, allow it to react for 2 –
20 minutes, depending on the type of stain & dilution factor. After that,
brush with soft brush then rinse thoroughly with clean water. Make small
test spot to verify result before actual use.
Dosage:
Dilute with water depending on the cleaning work. Can be diluted up to
50 times or more.
Handling & Precaution:
Contains only organic acidic compounds. Do not ingest. Do not get in
eyes, on skin or clothing. Keep the container closed when not in use.
Avoid breathing the mists. Wear a mask when handling. Use sufficient
ventilation to prevent build-up or mists. KEEP AWAY FROM CHILDREN.
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
KB 224 is a special water based polymer with silicone specially
designed to protect and keep a shine & wet look on vinyl, rubber,
plastic and leather or other such surface materials.
KB 224 protect surfaces from fading and cracking by reducing
ultraviolet light, while bringing out color, restoring luster and
shine, protects against abrasion. Eliminates static electricity to
reduce dirt attraction. If less shine is desired, lightly buff with
damp cloth.
Application:
Apply KB 224 with a clean cloth or sponge ( or spray ) with a cleaning
action. Spread evenly, allow to penetrate and chemically bond for a few
minutes then remove excess for a beautiful protective shine. On some
surfaces a two coat application provides best results. Apply as needed to
maintain shine and protective coating.
Dosage:
Use undiluted product.
Handling & Precaution:
This product may caused slipperiness on certain surfaces until it is
completely dry. May caused smearing on glass or other transparent
services. Avoid spills on eyes. Should avoid prolonged unnecessary contact
with skin. May irritate when exposed for a longer period on certain sensitive
skin. Harmful if swallowed. Keep away from children. Keep container
capped in a cool dry place
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
KB 273 is concentrated degreaser specially formulated to
penetrate, emulsify and disperse oil, grease, dirt, soot and
burnt / residual carbon from a variety of hard surfaces.
Specially designed for use in ovens, grills, chimneys, exitways,
smoke escapes, air vents where thick deposit of
soot/carbon is common by found. Most effective for oily
residues and its water base composition make easy
flushing.
Application:
Allow soaking time ( 5 – 30 minutes ) for effectiveness. Apply a
thin layer by spraying or brushing, then leave for soaking. Brush
and scrap gently to remove any hard soils if required then flush
with water. ( Use KB 212 for best results ) Protective measures is
suggested for cleaning personnel
Dosage:
Dilute with ratio of 1 : 10 ( max. ) with water depending on the dirt
thickness. Use concentrated product or lower dilution for tougher
stains. Dilute up-to 50 times for regular cleaning work. Repeat if
necessary
Handling & Precaution:
Avoid eye contact. Should avoid prolonged contact with skin.
Harmful if swallowed. Use protective gloves where contact is in
evitable
Packaging:
Available in pail of 20 lt.. Can also be custom packaged.
Catalyzed Oxygen Scavenger with polymers for
preventing pitting. Ideal for use with both hard and presoftened
make-up water.
Application
Can be injected directly into the boiler by means of a proportioning pump.
Advisable to gradually feed LC 102 by means of a chemical proportioning
pump into the storage section of the de-aerating heater as far ahead of
the boiler as possible to provide maximum effectiveness in high pressure
boiler operating from 100-600 psi. or where large amount of water is used.
Dosage
Initial : 3 quarts per 1,000 gallons or 3 : 4000
Maintenance: 1 quart for every 1,000 gallons of make-up water or 1 : 4000
Maintain 20-50 ppm (mg/l) in the boiler water. LC 102 can be used in
conjunction with other formula in our product line, but should not be used
in a boiler operating in excess of 600 psi.
Handling & Precaution
LC 102 is mildly acidic product and should be handled with care to prevent
personal injury. Wear protective clothing and eye protection. In case of
contact with skin, immediately flush with water. In case of contact with
eye, flush with water for 15 minutes and obtain immediate medical
attention.
Packaging
Available in pail of 20 lt.. Can also be custom packaged
LC 104 is an ideal single product boiler internal treatment, specially
formulated by blending sludge conditioner & oxygen scavenger for dual
function in packaged boiler systems. It can control not only calcium
carbonate & calcium phosphate deposits but also calcium sulfate and
barium sulfate. Highly concentrated alkaline product. Eliminates excessive
precipitation of solids and reduces sludge accumulation. The oxygen
scavenger prevents pitting corrosion in the boiler system. It is
environmentally safe, non-hazardous and non-corrosive.
Application
Used in packaged boilers below 5 Tons/Hr. For use with make-up water
hardness below 150 ppm and effectively disperses iron oxides as well as
calcium phosphate and clay. Injected directly into the boiler by means of a
proportioning pump.
Dosage
Initial : 2 quarts per 100 gallons or 1 : 200 ratio
Maintenance: 1 quart for every 100 gallons of make-up water or 1 : 400 ratio
Maintain 15-25 ppm (mg/l) of orthophosphate in the boiler waters with pH
between 11.0 – 12.0. Maintain Conductivity below 3000 µmho/cm. Consult
LifeChem Technical Services when Hardness is low or high.
Handling & Precaution
LC 104 is an alkaline product and should be handled with care to prevent
personal injury. Wear protective clothing and eye protection. In case of contact
with skin, immediately flush with water. In case of contact with eye, flush with
water for 15 minutes and obtain immediate medical attention. Triple rinse used
cans before reuse or disposal. Refer to MSDS for detailed information.
Packaging
Available in pail of 20 lt.. Can also be custom packaged.
LC 200A is safe, phosphatic alumunium cleaner and
brightener. It’s strong formula will dissolve any oxide layer and
also has the added benefit of providing a protective phosphatic
layer to keep aluminum surfaces looking at their best. The
non-toxic formulation also prevents further oxidation of the
surface and repels dust build up owing to its electrostatic
effect. It has penetrating agents that clings to alumunium
surfaces for maximum effective cleaning result.
Application
Use LC 200A undiluted for initial cleaning and brightening on tough or built-up soil
problem. Use diluted product for regular cleaning. Determine dilution depending on
contamination type & frequency of cleaning. For on-going maintenance use LC 301
for a protective and shiny coat. For maximum cleaning, apply LC 200A with a highpressure
washer
Dosage
The dilution will vary, depending on the condition on the surface to be cleaned. For
best result, rinse with a high-pressure washer or apply with a brush. For normal
cleaning & brightening; apply LC 200A at a dilution up to 1:20 with water. Allow the
solution to react with the surface for 1 – 3 minutes, and then rinse thoroughly with
clean water through a pressure washer. Do not allow LC 200A to dry on the surface.
Repeat application if necessary.
Handling & Precaution
Contains mild acid. Do not ingest. Do not get in eyes or clothing. Wear a face shield,
neoprene rubber gloves & protective clothing if spattering is expected. Keep the
container closed when not in use. Avoid breathing the mists if produced during
application by spraying. Use sufficient ventilation to prevent build-up of mists during
application.
Packaging
Available in pail of 20 lt. Can also be custom packaged.
Lc 270 is a water based general purpose cleaner to
Penetrate, emulsify and disperse oil, grease, dirt and
Grime and other types of soils from a variety of hard
Surfaces. Ideal for cleaning walls, floors, desks, light
Fixtures, automobiles, painted woodwork. Also can be
Used on metal surfaces such as stainless steel,
Aluminum, cooper and brass.
Application
Spray, mop, brush wipe, dip method are recommended. Use for
Cleaning walls, floors, desks, light fixtures, automobile, painted
Wood work.
Dosage
Dilute with ratio of 1 : 10 with water depending on the dirt
Thickness
Handling & precaution
Avoid spills on eyes. Should avoid unnecessary contact with
Skin. Can irritate when exposed for a longer period. Harmful if
Swallowed.
Packaging
Available in pail of 20 lt. Can also be custom packaged.
2458 Water Treatment Chemicals Suppliers
Short on time? Let Water Treatment Chemicals sellers contact you.
