1. PRODUCT OVERVIEW VHR steel strip-seal joint made by Vinh Hung Investment and Production Co., Ltd (Vinh Hung IP) comprises of two steel rails with anchor bars connected to embedded bars in the pier cap of headwall of abutment, elastomeric strip serves as the trough for drainage and debris, nosing materials: non-shrink mortar or concrete with minimum compressive strength of 40MPa. There are 2 main types of VHR expansion joint identified by the cross section of the steel rails: VHR-C steel rail expansion joint and VHR-F steel rail expansion joint. 2. PRODUCT CHARACTERISTICS Totally accommodate to longitudinal movement up to 100mm, and also vertical and transverse movements if any. Simple in design and installation, high load capacity and durability. Designed suitably for flush curb and central reverse. Totally water-tight. To ensure the long-lasting durability, VHR steel strip expansion joints are protected from corrosion with methods such as: 2-component epoxy coating, PU-based painting (Polyurethane), hot dip galvanization according to ASTM A123 standards and especially the Al â?? Mg spraying method (at the ratio of 5% Al and 95% Mg) which ensures anti-corrosion durability of up to 100 years, proven by salt-spraying test in 6000 hours (8-hour dry-wet cycle repetition) under ASTM B117 standards. MATERIAL PARAMETERS 1. PROPERTIES OF METAL ELEMENTS ITEMS Tensile strength, min Yield strength, min Elongation, min NO. 1 2 3 REQUIREMENTS 450 345 23 UNIT MPa MPa % STANDARD ASTM A709M PROPERTIES OF RUBBER SEAL UNIT REQUIREMENTS Point Mpa 1 2 3 4 5 Hardness Tensile strength, min Ozone resistance, content of ozone in the air 100pphm, 20% deformed at 40o C x 70h Elongation at break, min Hot air aging test in 70 hours at 100o C Tensile strength change, max Elongation change, max Hardness change 65 ± 5 7 No crack 250 - 20 - 40 0 - 15 STANDARD ASTM D2240 ASTM D412 ASTM D1149 ASTM D412 ASTM D573 ASTM D573 ASTM D573 ASTM D573 Installation of joints is critical to ensure the lifespan of the expansion joint and smooth traffic. Careful preparation of machinery, equipment, and highly specialized human resources is required for the installation of high quality expansion joints. The installation method shall be strictly followed to guarantee the actual performance of the product in service. 1. After finishing pavement, cut and clean he trend, adjust embedded bars, laym reinforcement bars on site 2 . Fix the deformed bars, install the fabricated joints, add distribution bars, anchoring bars to embedded bars. 3. Cure concrete, install rubber seal, allow traffic when concrete 4. Install formworks and pour non-shrink mortar or high-strength concrete to transition section, check the leveling of surface.
ABS Grade A Steel Plate and ABS High Strength Steel Plates
Condition : New Elongation : 10% min Coated Zinc : 35-45g/m2 Tensile Strength : 380-650 Weight: 100-350kgs/ coil Packing: PE film or according to customer's requirements Grade: CB240, SAE 1008 Suitable With Standards : ASTM-A641, TCVN 2503 : 1993, SS, EN 10244, 2, 2009
Condition : New Elongation : 10% min Coated Zinc : 35-45g/m2 Tensile Strength : 380-650 Weight: 100-350kgs/ coil Packing: PE film or according to customer's requirements Grade: CB240, SAE 1008 Suitable With Standards : ASTM-A641, TCVN 2503 : 1993, SS, EN 10244, 2, 2009
Coated Zinc : 20-120g/m2 Or According To Customer's Requirements suitable with standards: TCVN 2503: 1993, SS_EN_10244_2_2009, ASTM-A641 Elongation : 10% min Tensile Strength : 350-650 Condition : New Usage : Industrial
Coated Zinc : 20-120g/m2 Or According To Customer's Requirements suitable with standards: TCVN 2503: 1993, SS_EN_10244_2_2009, ASTM-A641 Elongation : 10% min Tensile Strength : 350-650 Condition : New Usage : Industrial
Specification of Hong Ky High Speed Steel Coil Slitting line General specification: 1. Material Thickness: 0.3 mm to 3.2 mm 2. Input Coil Width: 600 mm to 1350 mm 3. Coil outer diameter: �¦ 1000 mm to �¦ 1700 mm 4. Coil inner diameter: �¦508 or �¦610mm 5.Coil weight: max. 20 tons 6.Speed: 80 m / min ~ 200 m / min 7.Total machine weight: 80 tons Advantages of Hong Ky High Speed Steel Coil Slitting Line: Thanks to the double slitting system, quick adjusting the clearance of knife blade has achieved.The design brings customer efficiency, long life operation, and safety for user. 1. Double Slitting System: - Thanks to the double slitting system, quick adjusting the clearance of knife blade has achieved. - It is efficient because a knife blade set can be done outside the line. - It has become possible to experimentally cut outside the line before real operation in order to check the accuracy. - Since all hydraulic piping and electrical wiring are buried underground, the working ground is clean and easy for operator to work. 2. Gear Box: - Hong Ky high speed steel coil slitting line has 3 gear boxes (Reducer). All gear boxes are designed and manufactured by Hong Ky, then the design became compact and efficient. 3. Scrap disposal: - It is unique design. It is automatic. - After winding the scrap, the scrap is automatically dropped on the conveyor, and the scrap is conveyed to the scrap box. 4. Latest advanced mandrel shaft of Tension Reel: - Hong Ky has adopted one of the advanced and latest Mandrel Shafts Mechanism. The mandrel shaft is designed to minimize the amount of bending when pinching the edge of the metal sheet. 5. Line Design: - Line design is a crystal of technology that the steel industry has built over several decades. - It is efficiency, long life, and strong design. - Hong Ky high speed steel coil slitting line is classified roughly into 12 main parts. 6. Product liability: - The safety measurement is taken into consideration in order to meet the product liability law. - Ground hole are fully covered to increase safety for operator. - The moving parts are covered as much as possible. 7. User-friendly design: - Hong Ky high speed steel coil slitting line is easy to handle and taken every safety measures.
Aluminum UBC ingot and cone with al content 96% min
Aluminum UBC ingot and cone with al content 96% min
Dear Potential customers, I am Quang Minh from Hoihanh galvanized wire enterprise in Vietnam. We are specializing in supply high quality galvanized wire from Vietnam Thank you and hope receive reply from you. Just need serious and real buyers, not fake or cheater
Dear Potential customers, I am Quang Minh from Hoihanh galvanized wire enterprise in Vietnam. We are specializing in supply high quality galvanized wire from Vietnam Thank you and hope receive reply from you. Just need serious and real buyers, not fake or cheater
Fix Price 1750$ MT CIF ASWP Payment Terms : L/C SPECIFICATION MG-0.002% MN-0.003% ZN-0.004% TI-0.001% OTHERS-0.0002% AL NO LESS -99.7% SI-0.001% FE-0.004% CU-0.002% GA-0.003% Al96% + / - 1 FOB price of $ 1650 / MT, 100% LC payment, 50MT trial * ADC12 FOB price $ 2110 / MT100% LC payment, 50MT trial
96% Aluminum Ingots and ADC12 minum Ingots The shape of these 2 types is the same but different chemical components Al96% + / - 1 FOB price of $ 1650 / MT, 100% LC payment, 50MT trial * ADC12 FOB price $ 2110 / MT100% LC payment, 50MT trial
CopperCathodes99.99-99.97%CuPurePriceGradeAProductPrice(USDprice):1000MTorless:LME-6%,1500-3000Mt:LME-8%,3500-5000Mt:LME-10%,5000Mtandmore:LME-13%Terms:CIFtoallportsintheworld Productorigin : Democratic Republic of LAO Sand South Africa Dimension : 914 MM**12MM Weight : 125 kg(+/-1%) Netweight : 2 MT(+/-1%) Minimum quantity : 100MT Per Month Maximum number : 100,000MT/Month X 12 months
Hot dip galvanized steel coil (gi) Grade: ss grade 33-80, sgcc, sgch, sgcd1-sgcd3, sgc340-sgc570, sgcc, dx51d Thickness: 0.2-2.0mm Place of origin: vietnam Brand name: nam kim steel group Model number: sgcc, sgch, sgcd1-sgcd3, dx51d Type: steel coil technique: cold rolled Surface treatment: galvanized Application: wide construction range, household appliance special use: high-strength steel plate width: 600-1250mm Length: as per customer's requirement Coil weight : 3-24 mt - coil id: 508/610mm Zinc coating: z50-z350 Surface of the galvanized steel coil: normal spangle, minimize spangle Spangle steel grade: ss grade 33-80, sgcc, sgch, sgcd1-sgcd3, sgc340-sgc570, sgcc, dx51d Certificate: iso9001 Payment terms: t/t or l/c Delivery time: within 25 days after received the deposit Packaging & shipping Packaging detail: standard seaworthy export package
Hot dip galvanized steel coil (gi) Grade: ss grade 33-80, sgcc, sgch, sgcd1-sgcd3, sgc340-sgc570, sgcc, dx51d Thickness: 0.2-2.0mm Place of origin: vietnam Brand name: nam kim steel group Model number: sgcc, sgch, sgcd1-sgcd3, dx51d Type: steel coil technique: cold rolled Surface treatment: galvanized Application: wide construction range, household appliance special use: high-strength steel plate width: 600-1250mm Length: as per customer's requirement Coil weight : 3-24 mt - coil id: 508/610mm Zinc coating: z50-z350 Surface of the galvanized steel coil: normal spangle, minimize spangle Spangle steel grade: ss grade 33-80, sgcc, sgch, sgcd1-sgcd3, sgc340-sgc570, sgcc, dx51d Certificate: iso9001 Payment terms: t/t or l/c Delivery time: within 25 days after received the deposit Packaging & shipping Packaging detail: standard seaworthy export package Delivery detail: according to the quantity or as per customer's request .
Hot dip galvanized steel coil (gi) Grade: ss grade 33-80, sgcc, sgch, sgcd1-sgcd3, sgc340-sgc570, sgcc, dx51d Thickness: 0.2-2.0mm Place of origin: vietnam Brand name: nam kim steel group Model number: sgcc, sgch, sgcd1-sgcd3, dx51d Type: steel coil technique: cold rolled Surface treatment: galvanized Application: wide construction range, household appliance special use: high-strength steel plate width: 600-1250mm Length: as per customer's requirement Coil weight : 3-24 mt - coil id: 508/610mm Zinc coating: z50-z350 Surface of the galvanized steel coil: normal spangle, minimize spangle Spangle steel grade: ss grade 33-80, sgcc, sgch, sgcd1-sgcd3, sgc340-sgc570, sgcc, dx51d Certificate: iso9001 Payment terms: t/t or l/c Delivery time: within 25 days after received the deposit Packaging & shipping Packaging detail: standard seaworthy export package Delivery detail: according to the quantity or as per customer's request .
Specification and structure: - standard: jis g 3321 - technology: nof (non-oxydizing furnace) - coating mass symbol: az50 ~ az200 - material thickness: 0.20 ~ 2.0 (mm) - width: 600 ~ 1250 (mm) Quality standard: Hot-dip 55% aluminium-zinc Coated steel standard - jis g 3221 Dominant characteristics: - especially produced for various usage purposes - long life of 4 times longer than other normal - effective corrosion sheets - good heat resistance The anti-finger layer is equipped: - stain-proof and oxidization resistance - keeping the surface of the products shiny for a long time - to reduce cracking, scratching coating during stamping, rolling
Specification and structure - standard: jis 3322, jis 3312 - technology: full reverse roll coating - coating thickness: 10-30/15-30 micron - material thickness: 0.25 ~ 1.2 (mm) - width: 600 ~ 1250 (mm) Namkim color - pre-painted zinc-aluminium coated steel is made by nof hot-dip zinc-aluminium alloy coated steel material on the advanced technology and production line, diversified colors, lifespan many times longer than other pre-painted zinc coated steel, weathering resistance and good heat-protective effect.
Currently we have aluminium ingots 95%, 96% and Supply ability: 500 mt. Payment terms: l/c at sight. Origin in vietnam. Best regards
