POWER CABLE, Medium voltage cables armoured
POWER CABLES Fire Resistant & Flame Retardant Cables Please contact us for for details catalogue
POWER CABLE Medium voltage cables Please contact us for for details catalogue
POWER CABLE Low voltage cables Please contact us for for details catalogue
Capacitor Multiple choice
Direct centrifugal fans are a line of industrial fans that have many useful applications today. Widely used for industrial parks, factories, workshops or high-rise buildings, shopping malls... areas with large areas. Model: SCD-BNo Capacity: 0.75kW-30kW Voltage: 220V-380V Flow: 1500m3/h-60000m3/h Pressure: 200Pa-1300Pa
High pressure centrifugal fan drives indirectly Model: SCIK-CNo Capacity: 20kW-250kW Voltage: 220V-380V Flow: 9000m3/h-60000m3/ h Pressure: 3000Pa-16000Pa
Model: SCI-HNo Capacity: 5.5 kW - 3500 kW Voltage: 380V Flow: 6000m3/h - 400000m3/h Pressure: 2700Pa - 5600Pa
Indirect centrifugal fans are centrifugal fans whose motor structure is indirectly attached to the impeller through a belt or hard joint. Indirect centrifugal fans have all the same functions and roles as other centrifugal fans . That is the movement of air and gases entering at a certain angle compared to the direction of the incoming fluid. Product name: Indirect centrifugal fan Model: SCI-TNo Capacity: 0.2 kW - 300 kW Voltage: 380V Flow: 2000m3/h - 55000m3/h Pressure: 300Pa - 13000Pa
Indirect axial fans are axial fans with a motor structure designed to connect indirectly to the impeller through a belt. This line of fans is similar to other axial fans, which have suction and blowing directions parallel to the fan axis. Model: SAI-CNo Power: 0.37 - 30kW Voltage: 220 - 380V Flow: 1000 - 58000 m3/h Pressure: 100 - 900 Pa Transmission: indirect via belt Standard size: D300mm-D1200mm
Direct axial fan is a type of axial fan with a motor structure attached directly to the fan blades. This helps to increase the rotational force of the wings, creating quite a large amount of wind flow. Model: SAD-CNo Power: 0.37 - 37kW Voltage: 220 - 380V Flow: 2000 - 65000 m3/h Pressure: 120 - 1300 Pa Drive: direct
We are the professional manufacturer for Cable tray, Cable ladder, Cable trunking with many kind of finished product materials : HDG, Pre-painted steel, power coating.
We produce and install so many Low voltage MSB, Control panel, Distribution borad, Switch board, MCB consumer units for 5 stars hotel, resort, apartment, factoty, restaurant, hospital, school....
Cable Grout Industry standard high performance grout for the grouting of cables in post-tensioned concrete, void and fissure grouting, etc. Description A specially formulated Portland Cement shrinkage-compensated powder mix designed for the grouting of cables in post-tensioned concrete. The material readily mixes with water to produce a particularly fluid flowing grout which will penetrate and fill fine voids within and around the cables then harden without shrinking to give a high strength product. Uses include grouting of cable ducts, voids and fine fissures, support of cable anchor plates and ground anchors. Also to provide bearing or contact between structural elements, for grouting behind shafts and tunnel linings, and for underpinning, loose floor and road slabs. Once hardened and cured, high compressive strengths are achieved giving resistance to static and dynamic stresses. Cable Grout has a total chloride, sulphate and sulphide-ion content below that specified Advantages Does not contain aluminum powder nor any components which generate hydrogen gas, cardon dioxide or oxygen. Silica fume enhanced for low permeability. Non-metallic; will not stain or rust. Non-corrosive; does not contain chlorides. Zero bleed, even at high flow Excellent for pumping: Does not segregate, even at high flow. No build-up on equipment hopper. Superior freeze/thaw resistance. Even with his great fluidity, it can disperse water (thixotropic) Preparation - Genetic tubes must be cleaned with a high-pressure air compressor - Check the vents and pressure test for gen tubes - Repair leaks before grouting pumb Mixing - Water : mortar powder = 1 : 3.4 parts by weight. (6.8 litres of water per barrel) - With volume 15 liters: Use a colloidal solution mixer (to get the best results) Add water and continuously mix for 5 minutes to achieve a uniform Continue to maintain slowly mixing during grout pump Important Note Non mixing by hand Yield As a guide 1 barrel yields approximately 14 litres of mortar Shelf Life: 9 months Packaging: 25kg/barrel Storage Conditions - Store properly in dry conditions in undamaged and unopened original sealed packaging Cleaning of tools - Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed
Noise Barrier
Resin, flower pot, relief, statue, desk lamp.
Lights, lamp shade, furniture from plastic string and natural materials.
Electric fan, water filter, water pumps, household plastic, wire and cable, inverter, stabilizers, transformer, gum rosin, activated carbon.
Disposable medical face masks, water purifiers.Oem service, transportation service.
Kangaroo Chest Freezer, INVERTER technology, NANO SILVER antibacterial deodorant technology, COOPER evaporator and gas R600a, /220V-240V/50HZ, net capacity: 327L/258L/252L/290L/140L/90L, Energy Efficiency rate 5 star, cabinet: white painted aluminum alloy, Noise level: 38�·42dB, 4 moving wheels, CFC-free, color: white/grey
