High performance transformer oil purification systems and auxiliary equipment for maintenance of energy management. UVM offers a variety of systems designed for degasification, cleaning, drying, regeneration, purification, recycling, filtration , recovery, pumpdown, azotizing, heating, removal of water and particulate matter from transformer, turbine, cable and other oils.
Distillation column, fractional distillation column, alcohol distillation column, gas distillation column, oil distillation column, petroleum distillation column.
Equipment and materials for gas and oil industry..
Applications: designed for pumping condensed waste steam from stationary steam turbines and heating steam condensate (drain water) from heat exchangers in the thermal power stations that burn organic fuel. May be also used to transfer water in heating plants and water supply systems. Design: aksv series pump units consist of a centrifugal pump and an induction motor mounted on the motor stool. They are connected by means of a rubber-bushed (pin-and-bushing) flexible coupling. The pumps are electrically driven vertically suspended, can diffuser, single-stage (ksv 125-55) or multistage centrifugal pumps with inducer and single flow impeller arrangement (with all the impellers facing the same way). An outer casing (barrel) and an inner casing (withdrawable element or cartridge) are the major pump components. The barrel is a construction made of steel plate by complete welding process, which integrates a suction chamber (in the form of a can) and a discharge chamber (the discharge head proper). Pump support feet and weld-end suction and discharge nozzles are welded to the barrel. The inner casing (a rotating assembly) of ring-section type comprises a bare rotor, a shaft seal bearings, stage casings with built-in diffusers and a delivery cover. The design of pump shaft seal chamber provides for both housing a mechanical seal (-t) and packing the stuffing box (-s). The shaft of the pump make КсВ 125-140-3М is sealed only by means of packed gland.
Applications: designed for handling liquefied hydrocarbon gases, volatile flammable and inflammable liquids as well as solutions of inorganic alkalis (sodium hydroxide) at the process plants in the oil-refining industry. May be also used to transfer water and condensate in the steam and water circuit systems. Design: ndms series motor pump units consist of a centrifugal pump and an induction motor in the explosion-proof version, which are mounted on a common fabricated base plate. The pump and motor shafts are connected by means of a flexible coupling. The pump units shall be rigidly anchored to the foundation, and piping shall be also rigidly connected to the pumps. The pumps as components of the pump units are electrically driven horizontal, centreline-supported, multistage ring section centrifugal pumps with rotor axial thrust balancing by a balance drum.
Dynamic, volumetric.
CMM-12R is designed for extension of transformer service life by restoration of dielectric strength and chemical composition of electrical insulation oil. In the process of oil regeneration, decomposition products and acidic compounds are removed, the oil is clarified, its oxidation stability is improved, and gas solvency is reduced. The unique feature of the CMM our units is the ability to regenerate transformer oil directly in a transformer with the transformer either online or offline. The functions of the unit: *Oil regeneration; *Thermal vacuum drying of oil; *Vacuum treatment of transformer; Such regeneration of oil is capable of removing sludge from paper insulation and capturing it with the sorbent. One of the advantages of the regeneration unit is the use of Fuller`s earth sorbent, which can be reactivated many times. This gives the unit the capability to process oil continuously without stops to change saturated sorbent. Even after the sorbent is completely exhausted after 1.5 to 2 years of use, it is completely environmentally safe and can be used as a filler for construction materials and mixes. The CMM 12 our unit is controlled by a computer with special status software. The scanner control system offers the operator full control of all components. The operator can control the equipment, switch to various modes of operation, monitor sensor indications and access event flow. As requested by clients, the CMM-12R can be controlled remotely via the internet. If GlobeCore assistance is required, we can simply connect to the unit through the internet and monitor the entire operation process - if there is a problem, we will see it. Many of our clients purchase equipment for operation in unstable climates, explosive environments and even at sea. The CMM units can be manufactured in various optional designs. The most popular and convenient design is placement of the unit on a one or two axle trailers - this trailer has a metal frame covered with metal sheets and is equipped with an operator room.
Tire regenerate of the RShTN type received by a thermomechanical method from automobile tires. Regenerate is available in rolls used for the production of rubber products for various purposes (in the tire industry, production of RTG ). The tire regenerate meets the requirements of TU U 6-25521987.009-2000 "Thermomechanical tire regenerate".
Biodiesel equipment, rape seed.
Oil processing equipment, used oil purification plant, oil purifier, transformer oil regeneration, fuel cleaning plant, fuel reclamation unit, wastewater treatment machine, Nan modification of concrete composition.
