Cat.8 series 180 Tool Free Keystone Jack Shielded Cat.8 (6A) Cat.8 S/FTP 24AWG Patch Cord Cat.8 S/FTP 22AWG Screened Solid Cable RJ45 Field Terminable Plug (C8/C6A)
This antenna system consists of two functional blocks, the LNA portion and the patch antenna. CONFIGURATION RF Cable - RF Coaxial Cable, 2.7± 0.2mm - Cable Length : 5M ± 5cm - RF Connector : SMA 180(M) / MCX 90 (M) GENERAL ENVIRONMENTAL CONDITIONS - Operation Temperature : -40 to + 85 - Storage Temperature : -40 to + 85 - Relative Humidity : 40% to 95% ELECTRICAL SPECIFICATIONS - Input Voltage : Min:2.5V Typ:3.0V Max:5.5V - Power Consumption : Typ: 10mA. Max: 15mA. @3.0V ANTENNA - Antenna Dimensions : 25 x 25 x 4 mm - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - GAIN : 1575.42MHZ : -3dBi Typ. @zenith 1602MHZ : -5dBi Typ. @zenith - Polaration : RHCP LNA and FILTER - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - Gain (without Cable) : 1575.42MHz:28 dB Min.30 dB Typ.( + 25 ± 5) 1602MHz:28 dB Min.30 dB Typ.( + 25 ± 5) - Noise Figure : 2.0 dB Typ. ( + 25 ± 5 ) / 2.6 dB Max. ( + 85 ) - Out Band Rejection : 1587.5 ±140MHz 15dB Min - Output Impedance : 50 - Output VSWR : 2.0 Max TOTAL SPECIFICATIONS (Through Antenna, LNA, Cable and Connector) - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - Gain : 1575.42MHZ: 27± 3dBi @zenith 1602MHZ: 29.5± 3dBi @zenith - Output Impedance : 50 - Output VSWR : 2.0 Max
This antenna system consists of two functional blocks, the LNA portion and the patch antenna. CONFIGURATION RF Cable - RF Coaxial Cable, 2.7± 0.2mm - Cable Length : 5M ± 5cm - RF Connector : SMA 180(M) / MCX 90 (M) GENERAL ENVIRONMENTAL CONDITIONS - Operation Temperature : -40to + 85 - Storage Temperature : -40 to + 80 - Relative Humidity : 40% to 95% ELECTRICAL SPECIFICATIONS - Input Voltage : Min:2.5V Typ:3.0V Max:5.5V - Power Consumption : Typ: 10mA. Max: 15mA. @3.0V ANTENNA - Antenna Dimensions : 25 x 25 x 4 mm - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - GAIN : 1575.42MHZ : -3dBi Typ. @zenith 1602MHZ : -5dBi Typ. @zenith - Polaration : RHCP LNA and FILTER - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - Gain (without Cable) : 1575.42MHz:28 dB Min.30 dB Typ.( + 25 ± 5) 1602MHz:28 dB Min.30 dB Typ.( + 25± 5) - Noise Figure : 2.0 dB Typ. ( + 25 ± 5) / 2.6 dB Max. ( + 85 ) - Out Band Rejection : 1587.5 ±140MHz 15dB Min - Output Impedance : 50 - Output VSWR : 2.0 Max TOTAL SPECIFICATIONS (Through Antenna, LNA, Cable and Connector) - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - Gain : 1575.42MHZ: 27± 3dBi @zenith 1602MHZ: 29.± 3dBi @zenith - Output Impedance : 50 - Output VSWR : 2.0 Max
This antenna system consists of two functional blocks, the LNA portion and the patch antenna. CONFIGURATION RF Cable - RF Coaxial Cable, 2.7± 0.2mm - Cable Length : 5M ± 5cm - RF Connector : SMA 180(M) / MCX 90 (M) GENERAL ENVIRONMENTAL CONDITIONS - Operation Temperature : -40 to + 85 - Storage Temperature : -40 to + 85 - Relative Humidity : 40% to 95% ELECTRICAL SPECIFICATIONS - Input Voltage : Min:2.5V Typ:3.0V Max:5.5V - Power Consumption : Typ: 10mA. Max: 15mA. @3.0V ANTENNA - Antenna Dimensions : 25 x 25 x 4 mm - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - GAIN : 1575.42MHZ : -3dBi Typ. @zenith 1602MHZ : -5dBi Typ. @zenith - Polaration : RHCP LNA and FILTER - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - Gain (without Cable) : 1575.42MHz:28 dB Min.30 dB Typ.( + 25 ± 5) 1602MHz:28 dB Min.30 dB Typ.( + 25 ± 5) - Noise Figure : 2.0 dB Typ. ( + 25 ± 5) / 2.6 dB Max. ( + 85 ) - Out Band Rejection : 1587.5 ±140MHz 15dB Min - Output Impedance : 50 - Output VSWR : 2.0 Max TOTAL SPECIFICATIONS (Through Antenna, LNA, Cable and Connector) - Frequency Range : 1575.42 ± 10 MHz. / 1602 ± 8MHz - Gain : 1575.42MHZ: 27± 3dBi @zenith 1602MHZ: 29.5± 3dBi @zenith - Output Impedance : 50 - Output VSWR : 2.0 Max
Main Technical Specification - Frequency Range (MHz) : 434 - Bandwidth (MHz) : ±3 - VSWR : 2.0 - Gain(dBi) : 1.80 - Max Input power (W) : 50 - Input Impedance () : 50 - Polarization Type : Vertical - Antenna Length(mm) : 88mm(90) / 108mm (180) - Connector Type : SMA
Torque from 105 kgf-cm to 35000 kgf-cm Power: AC110V/ AC220V/ AC24V/ DC24V Switch time (Open-to-close) from 1 second to 143 seconds Could also assemble with ball valves, butterfly valves and so on
UM-1-AC110V/AC220V Torque: 350 kgf-cm (AC110V); 362 kfg-cm (AC220V) Open-to-close: 10 seconds Power: 10W
UMS-AC110V/AC220V Torque: 105 kgf-cm Open-to-close: 23 seconds Power: 3~4W
VHF Antenna 497-01001-00 Item Number : 497-01001-00 Key Specifications Frequency range : 156~164 MHz Gain : 3 dBi Configuration : 1/4 Wave V.S.W.R. :
Rigid PCBA, Flex PCBA, Metal Core PCBA, Functional Test & Box-Build
#Autodoor #AutomaticDoor #AutomaticDoorSystem
Wide variety of Metal Core PCBA : Aluminum, copper or iron
Single layer, double layer or multi-layer
single-layer, double side or multi-layer
Single Side : Maximum shipping Panel Size 470mm*570mm Finished Board Thickness : Minimum Board Thickness : 0.6mm+/-0.1mm , Maximum Board Thickness : 2.0mm+/-10% Dielectric Material : Heat Conductive Glue / FR4 Aluminum Type : 5052 Copper Thickness : 1/2~2oz Trace Width / Spacing : Minimum Line Width / Spacing(Internal&External) 0.1mm ,The tolerance followed by IPC-6012 Surface Finish : Immersion Gold(Ni/Ru) 0.025~0.1um /Lead Free HASL (Min. 2.5um)/OSP (Entek CU106A) 0.2~0.5um Solder Mask : LPI Test : Hi-Pot Test
Layers: FPC 1~4 L Finished Board Thickness with Copper : Min 0.075mm (1L) / Max 0.3mm (2L) Finished Board Thickness Tolerance: �±0.02~0.04mm Impedance Control :+/-10% Base Copper Thickness : Standard : 1/3oz,1/2oz,1oz / Spcial:2oz Base Film Thickness:Standard:0.5mil , 1mil / Special : 2mil Stiffener:PI / FR-4 /SUS Finished Hole Diameter:Min { }0.15mm / Max { }6.30mm Finished Hole Diameter Tolerance PTH�±3mil(�±0.075mm) npth�±2mil(�±0.05mm)
Layers : Sample 1~32 / Mass Production 1~20 Size :Max shipping size is 600mmx550mm , +/-0.15mm Finished Board Thickness: Min 0.4mm(4L)/0.6mm(6L),+/-0.1mm (Max) 3.6mm(2.2~3.6mm depends on material), +/-10% Copper Thickness :1/3~5oz (Depends on material) Impedance Control :+/-10% Via Holes (Min) : Mechanical Drill:0.2mm / Micro Via:0.1mm PTH+/-0.075mm NPTH +/-0.05mm Aspect Ratio : Sample :10:1 / Mass Production :8:1 Min Trace(Width/Spacing) : Internal 0.075mm / External 0.075mm The tolerance followed by IPC-6012 Advance Process : Blind Routing Cavity,Coil Board,Plug Hole With Epoxy,Half Hole Plated Spacing between Pads : Min :8 mil
Automatic PCB Lead Cutter > > Product No. : KA-66 FEATURES Best Selection for medium of high volume production. This model is designed to trim the extra long leads automatically and efficiently on the PCB that components inserted and soldered. A pair of conveyor chain is equipped in the model in which clamp and deliver the PCB to the blade turning in high speed for trimming. Warp prevention device is equipped to ensure no damage on boards. Expandable in function and working independently- The model can be optional connecting in line with wave soldering machine by Connection Bridge and operates automatically. The Tungsten Carbide Blade is excluded in the machine. SPECIFICATIONS Dimension:900(L) x 670(W) x 800(H) m/m Power:220V 50/60HZ,Net Weight:115Kgs Feeding Speed:0 - 3 m (Adjustable) RPM of Spindle:4500 HP:3/4 HP Min. Lead Height:1.0mm Min MAX.PCB Working Size:500mm(L) x 280mm(W)
NTG-520N Pre-scored PCB Depaneling machine/ de-panelizer. Separate PCB along with V grooves. [Feature] 1. Separating the V-cut panel boards in the principle of non-bending stress. 2. The knives are adjustable both in axial and radial directions. 3. The round knives separate the board within the V-groove. Slightly adjust according to PCB thickness. 4. The depaneling maximum of PCB width is 160mm, the PCB length is unlimited. [ Specification ] Powerï¼?110V/220V, 50/60HZ Dimensionï¼?(L)430 x (W)430 x (H)520 Weightï¼?36 kgs PCB thickness rangeï¼?0.8-2.0mm www.renthang.com renthang@renthang.com
NTG350 Pre-scored PCB Depaneling machine, PCB Separator: Pneumatic Type FEATURES The machine was designed to depanel pre-scored panelboards carefully, without bending or tension stress. Even sensitive SMD-Components like ceramic capacitors, will not be damaged by the depaneling process, or thin board even to 0.3mm cab be worked safely. Due to the special design of the knives also boards with high components placed close to the edges can be depaneled safely.Based on a proven method of depaneling, wedge-shaped knives are used to cut the panels within the groove. This enables the boards less than 1mm thickness to be separated safely and without creating stress. This machine is pneumatically driven using standard parts. It is noiseless operation with none of usual compressed air noises. Rigid design without vibration in operation The PCB with sensitive SMD capacitor or thin board even to 0.3mm can be worked safely.Gap for insertion of the board can easily be adjusted by means of the adjusting knob in front of the machine.Gap for insertion of the board can easily be adjusted by means of the adjusting knob in front of the machine.Gap for insertion of the board can easily be adjusted by means of the adjusting knob in front of the machine. Depaneling process without vibrations Pneumatic control placed in a separate unit for easier maintenance. SPECIFICATIONS â?¢Easy maintenance and operation. Air source¡GCompressed air 5kg/cm2 Dimension¡G(L) 720 x (W) 500 x (H) 1070 mm Weight¡G190Kgs Knife length¡G350mm PCB thickness range¡G0.3mm ~ 3.0mm www.renthang.com renthang@renthang.com +886-2-82011187
