Steel Suppliers and Manufacturers

HR Coil/Sheets/Plates of various sizes and grades available of JSW Brand.

GI Coils/Sheets of JSW Brand. Thickness: 0.25mm - 3.15mm Coating: 80 GSM - 550 GSM Spangle: Regular, Minimised, Skin Passed & Zero Spangle

CRCA Coil of brand JSW.

1. Basalt short fiber - a new material to replace steel fiber. Basalt short fiber is an inorganic mineral fiber with a length of less than 50mm, which can be evenly dispersed in cement concrete. 2. Characteristics of basalt short fiber (1) the specific gravity of steel fiber is 7.8 and that of cement concrete is 2.5. After mixing, the specific gravity of steel fiber is higher than that of cement, and the cement will sink and have poor dispersion. The specific gravity of basalt short fiber is 2.6, which is basically equivalent to that of cement concrete. After mixing, it does not sink, has good dispersion, is degradable, and is green. The road surface will not be as hard as steel fiber, resulting in car driving noise.. (2) Basalt staple fiber is a real "multifunctional" fiber. Acid and alkali resistance (especially alkali resistance, fully applicable to cement concrete), low and high temperature resistance, insulation and sound insulation. The tensile strength is three times that of steel fiber. The corrosion resistance of basalt fiber is better than that of steel fiber. The compressive strength is 20% higher than that of steel fiber, which is suitable for harsh environment. It has excellent comprehensive performance. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of 50% steel fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with cement concrete and mortar. Fresh basalt fiber concrete has stable volume, good workability and durability, and has excellent high temperature resistance, impermeability, crack resistance and impact resistance.

Hex Nipple

Square Plug Fig

For these Inconel and Incoloy Olets and cost-effective procedures for molding nickel alloy components to shape and polish, grinding is preferred over machining, water-jet, or laser. The grinding wheels in Inconel and Incoloy Olets are less impacted by work hardening and remain sharp and long-lasting due to the hardness of the abrasives utilized. After reaching full maturity by induction heating to 1,300 �?�°F (704 �?�°C), Inconel Olets can be rolled-threaded without increasing grain size. Inconel Outlet Fittings are used in severe situations because they resist oxidation at high temperatures. Inconel or Incoloy Outlet Pipe Fittings work-harden during machining, providing them with more strength and gumminess than steel when improved temperature performance or strength is required. A global steel manufacturer produces Inconel and Incoloy Olets using high-quality raw materials and cutting-edge technology and machinery. These items come in a variety of sizes, shapes, and styles to meet the needs of diverse industries. Our high-quality Inconel and Incoloy Olets are a low-cost, high-quality replacement for a wide range of typical goods. In several industries, Inconel and Incoloy Olets are employed. Our engineers are working to increase the quality of Inconel and Incoloy Olets while also cutting down on production time to ensure faster delivery. Fabrication, Oil & Gas, Fertilizers, Electronics, Construction, Chemical Industries, Plumbing, Power Plants, Modern Architecture, Petroleum Industry, General Purpose Applications

Syphon Size 1/2 inch Condensate Pot Size Pipe size 2, 3, 4, 6 and larger size upon request. Standard length: Pipe length 8, 10, 12, and larger length upon request. Pipe Schedule: 40, 80, 160, seamless pipe. NPT as per ANSI B2.1 taper pipe thread furnished. Socket weld as per ANSI B16.11 Butt weld as per ANSI B16.9 Working pressure: 6000 PSIG (41.34 MPa). Snubber Size Bore sizes 3/4 to 10 in diameter Travel ranges from 5 to 20 Load capacities from 738 lbs. to 187,900 lbs. Pipe Clamps 1/2 -18 Inch Types Condensate Pot, Air Header, Pipe Clamp, Quick Release Coupling, Syphon Tube / Pipe, Pipe Clamp, Snubber, Lock Nut For O-seal, Gauge Snubber, Thermocouple, Thermowell, Gauge Adaptors, Gauge Saver, Pressure Gauge Accessories, Mini Ball Valve, Over-Pressure Protector, Cooling Tower, Adjustable Snubber Application Power/ gas/ petroleum/ chemical/ metallurgy/ shipbuilding etc. Air Header Size Inlet Connection Size:1/2, 3/4, 1 inch Raised Face, Female NPT, BSPT, BSPP 2,3 & 4. inches Drain Connection Type:Female NPT, BSPT, BSPP Drain Port Size:1/2, 3/4, 1 Working Pressure:6000 psi [413 bar] Test Certificates EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third Party Inspection Report, etc

Duplex Steel Instrumentation Accessories are frequently utilized in industrial applications, such as the manufacture of seawater heat exchangers and chemical containers for use in high-concentration chloride environments, due to their great combination of superior mechanical qualities and high corrosion resistance. In the production of duplex stainless steel items, welding is widely used. It has properties such as heat resistance, general corrosion resistance, pitting resistance, stress corrosion cracking resistance, crevice corrosion resistance, extended serviceability, high tensile strength, high yielding strength, and anti-corrosive body, among others. Duplex Steel Instrumentation Accessories come in a variety of shapes and sizes, and they are employed in the plumbing system for a variety of tasks and purposes. Duplex Steel Instrumentation Flare End Fittings are high-performance accessories made from the most common duplex stainless steel grade, which contains molybdenum, nitrogen, and nickel. These are austenitic-ferritic steel accessories with excellent corrosion resistance and strength. This valve alloy is also resistant to localized corrosion, such as pitting, crevice corrosion, and intergranular corrosion. These Instrumentation Condensate Pots are susceptible to chlorides stress corrosion cracking and have superior high-temperature oxidation resistance. In services such as brackish water, marine conditions, and closed-loop water systems, these valves have exceptional resistance. In comparison to other grades, this valve grade is extremely ductile and robust

Specification of SS Instrumentation Accessories Syphon Size 1/2 inch Condensate Pot Size Pipe size 2, 3, 4, 6 and larger size upon request. Standard length: Pipe length 8, 10, 12, and larger length upon request. Pipe Schedule: 40, 80, 160, seamless pipe. NPT as per ANSI B2.1 taper pipe thread furnished. Socket weld as per ANSI B16.11 Butt weld as per ANSI B16.9 Working pressure: 6000 PSIG (41.34 MPa). Snubber Size Bore sizes 3/4 to 10 in diameter Travel ranges from 5 to 20 Load capacities from 738 lbs. to 187,900 lbs. Pipe Clamps 1/2 - 18 Inch Types Condensate Pot, Air Header, Pipe Clamp, Quick Release Coupling, Syphon Tube / Pipe, Pipe Clamp, Snubber, Lock Nut For O-seal, Gauge Snubber, Thermocouple, Thermowell, Gauge Adaptors, Gauge Saver, Pressure Gauge Accessories, Mini Ball Valve, Over-Pressure Protector, Cooling Tower, Adjustable Snubber Application Power/ gas/ petroleum/ chemical/ metallurgy/ shipbuilding etc. Air Header Size Inlet Connection Size:1/2, 3/4, 1 inch Raised Face, Female NPT, BSPT, BSPP 2,3 & 4. inches Drain Connection Type:Female NPT, BSPT, BSPP Drain Port Size:1/2, 3/4, 1 Working Pressure:6000 psi [413 bar] Test Certificates EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third-Party Inspection Report, etc

Specification of Duplex Steel Instrumentation Fittings Imperial Size 1/2 to 2 Size 1/16 OD to 2 OD, 2mm OD to 50mm OD Thread NPT, BSP, BSPT, UNF, ISO, SAE, MS, AN, weld ends etc. Pressure Rating 6000PSI for Stainless Steel, 300/1000/3000PSI for Brass Temperature Ratings Up to 1000F (537C) Types Tube to Union, Tube to Male, Tube to Female, Instrument Pipe Fittings, Accessories Application Power/ gas/ petroleum/ chemical/ metallurgy/ shipbuilding etc. Our service Nace Mr 01 75 Sour Service Impact Test As Per Ug 84 Macro Structure Analysis Hydrogen Induce Cracking Test (Hic) Sulphide Stress Cracking Test (Sscc) Cryogenic Services (Cryo),hydrogen Services (H2) Helieum Leak Test Dye Peniterant Test (Dp) Magnetic Partius Test (Mp) Post Weld Heat Treatment (Pwht) Ultrasonic Test (Ut) Hydro Test, Etc. Test Certificates EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third Party Inspection Report, etc Production Technique Forged/ Heat treated and machined.

Duplex steel instrumentation fittings have higher mechanical strength and higher ductility. Moreover, these fittings have a good ability to resist stress corrosion cracking, ranging from nominal to subzero temperatures. These duplex steel instrumentation fittings are tested under different testing measures to ensure their hardness, mechanical strength, reliability, and functionality in adverse applications. These Duplex Steel Instrumentation Fittings exhibit a low coefficient thermal expansion, sulfide stress corrosion cracking resistance (sour-gas environment), high thermal conductivity, etc. Duplex Steel Instrumentation Fittings are well demanded due to their high mechanical strength and good welding ability. Duplex Steel Instrumentation Fittings are usually used in heat exchangers, tubes, and pipes for the production and handling of gas and oil, mechanical and structural components, power industry FGD systems, cargo tanks, vessels, piping and welding consumables for chemical tankers, etc. Duplex Steel Instrumentation Fittings have a high strength means that the range of 0.2% PS for the current duplex grade is from 400-500 MPa. Our Duplex Steel Instrumentation fittings are available in various types like male elbow, female elbow, front ferrule, back ferrule, ferrule nut, bulkhead nut, union elbow, union tee, male branch tee, male-run tee, female-run tee, female branch tee, male connector, female connector, bulkhead male connector, bulkhead female connector, union cross, bulkhead union, ferrule nut, etc. We conduct various tests on our products to ensure they are error-free and suitable for use in various industries

Hindalco's cold rolled coils are precision-finished to match international standards. They have good shape, high tolerance, versatility and blemish-free surfaces. They are used in commercial and general engineering applications such as bus bodies, cladding and fan blades. The company meets the demands of its ever-growing clientele with continuous upgrades and process improvement. Thickness : 0.16 mm to 4 mm Width : 50 mm to 1600 mm Alloys : 1050/1100/1070/1200/3103/3105/3003/5052/5005/5754/5083/8011

Standard ASTM A182 / ASME SA182 Dimensions ASME / ANSI B16.11, MSS-SP-97, MSS-SP-79, JIS B2316, BS 3799 etc Size 1/8-4 (DN6-DN100) Connect Type Welded, threaded, BW, SW Process Free forging, plate cutting forged Diameter DN15 ~ DN40 Class 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS Types Weldolet, Sockolet, Threadolet, Nipolet, Elbolet, Threaded Elbolet, Socket Weld Elbolet, Sweepolet, Insert weldolet, Brazolet, Flexolet buttweld, Flexolet Socket Weld, Flexolet Threaded, Nipo Flange

To assure quality, Global steel's Duplex steel Olets are made using high-quality materials and put through a stringent quality check at each stage of production. The microstructure of Duplex Steel Olets is two-phase, with ferritic and austenitic stainless steel grains. It has numerous advantages and features that make it suited for a wide range of industrial applications. Duplex Olets are manufactured in compliance with global quality specifications. Our Duplex steel Olets are rust-resistant, strong, and long-lasting. We also offer Duplex steel Olets in bespoke sizes to meet the needs of our customers. Global Steel delivers defect-free Olets thanks to stringent quality control from material selection through product packing. Our professionals are working to improve the quality of Duplex steel Olets while also reducing the production time to ensure a speedier delivery. Global steel provides products with the highest possible value at reasonable prices and within the timeframe indicated. Duplex steel Olets have abrasion resistance, corrosion resistance, durability, dimensional correctness, improved performance, little maintenance, and a long service life. Duplex steel Olets are used in a variety of industries, including oil and gas, food and dairy, structural pipe, and paper and pulp. Our Olets are manufactured of Duplex steel and are suitable for both high-temperature and general-purpose use. Duplex Olets are known for their high performance and adaptability to their clients needs

Standard ASTM A182 / ASME SA182 Dimensions ASME / ANSI B16.11, MSS-SP-97, MSS-SP-79, JIS B2316, BS 3799 etc Size 1/8-4 (DN6-DN100) Connect Type Welded, threaded, BW, SW Process Free forging, plate cutting forged Diameter DN15 ~ DN40 Class 2000 LBS, 3000 LBS, 6000 LBS, 9000 LBS Types Weldolet, Sockolet, Threadolet, Nipolet, Elbolet, Threaded Elbolet, Socket Weld Elbolet, Sweepolet, Insert weldolet, Brazolet, Flexolet buttweld, Flexolet Socket Weld, Flexolet Threaded, Nipo Flange