Clamp Flexible Rubber Joint Clamped Rubber Joint Rubber Joint 1. Oil resistance Flexible Rubber Joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement axial expansion, etc. 2. According to different materials, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange standard: ANSI, JIS, BS, DIN, GB, ect Item No. Parts Name Parts Material 1 Hoop Q235 304 316L 2 Outler layer glue IIR, CR, EPDM, NR, NBR 3 Skeleton layer polyester cord 4 Inner layer glue IIR, CR, EPDM, NR, NBR
Limited Flexible Rubber Joint KXFT Single Rubber Joint Rubber Joint The product is mainly used for conveying liquid, gas, solid materials such as metal pipe flexible connection can compensate for displacement, vibration isolation noise, is a novel rubber damping products. High Strength Rubber Joint combines the mechanical extensibility of the metal expander and the multi-displacement function of the flexible rubber joint. It is not only mechanically expandable for installation and dismantling but also compensates for changes in the temperature of the pipe during operation Linear expansion and contraction as well as compensate for the ground settlement caused by the pipeline center of gravity and other causes of angular deviation, but also to eliminate vibration and noise transmission, is a versatile pipe compensator. Features Minimal axial dimensions Limited weight Low warping forces High-resistance to work High-capacity acoustic damping No. Name Meterial 1 Inner & Outer Rubber NR, NBR, EPDM 2 Key Frame Nylon cord fabric 3 Reinforcing Ring steel wire 4 Flange Q235
PTFE flexible rubber expansion joint Single Rubber Joint Pipe Expansion Joint 1. Acid resistance Flexible Rubber Joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement, axial expansion, etc. 2. According to different materials manufacture, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange connection standard is GB4216.3-4216.5. No. Part Meterial 1 Body NR, CR, IIR, NBR, FKM, EPDM 2 Inner & Outer Rubber NR, CR, IIR, NBR, FKM, EPDM, PTFE 3 Body Carcass Nylon cord fabric 4 Reinforcing Ring Multi-strand coppering steel wire 5 Flange Cast and forged carbon steelStainless steelPlastic (CPVC, PVDF, PPH, UPVC, RPP) MAIN DATA Nominal Diameter(DN) Length L Axial displacement Horizontal Isplacement Angular deflection mm inch mm Extension Compression mm (a1+a2) 32 1¼ 95 6 9 9 15º 40 1½ 95 6 10 9 15º 50 2 105 7 10 10 15º 65 2½ 115 7 15 11 15º
UHMWPE fender is made of 100% UHMWPE material which will not warp, crack, splinter or corrode.It has become a popular product which is widely used in dock as it is UV resistance and no water absorption.UHMWPE fender still has the performance of prolongation and high tensile strength and could immersed in seawater perennially. The most important is that Ultra-high molecular weight polyethylene (UHMWPE) dock fender could avoid the impact damage between ships and dock .Because of the high impact resistance performance, UHMWPE dock fender instead of the traditional steel ones is widely used in ports and docks at home and abroad.
IT-SB Series Features: The integrated metal plate provides higher load caring capacity in compression, shear or combined compression and shear loads higher. Iso Tech Sandwich Buffer can withstand load from 200Kgs to 1000 Kgs Applications: Diesel Engines Off road vehicles Construction Machinery Mobile Applications
IT-CP Series Features: The CUP MOUNT is a universal mount with combination of compression and shear load, Designed for integral fail safe mount. Protect from oil contamination. Applications: Compressors Blowers Industrial Machinery AC & AHU Units
Features: The instrumount design can be used in variety of applications, these mounts are numerous load range, easy to install. Applications: Control Panels Pumps Electronic Equipments Blowers
IT- SH Series Features: The Shock Mount protects sensitive equipments from high level shock and vibration. Prevent impact from off-road environments Applications: Equipment in transport Drop Force Shipboard Equipments’
IT-I Series Features: The instrumount design can be used in variety of applications, these mounts are numerous load ranges, easy to install. Applications: Control Panels Pumps Electronic Equipments Blowers
IT-CM Series Features: The CUP MOUNT with combination of compression and shear load, Designed for integral fail safe mount. Protect from oil contamination Applications: Compressors Ship Board Industrial & Vehicle engines Blowers
IT- SW Series Features: The sandwich mountings is bonded with center plate and outer plates to withstand high compression force with minimum deflection Applications: Engines Radiators Construction machines
Features: The Shock Mount protects sensitive equipments from high level shock and vibration. Prevent impact from off-road environments Applications: Equipment in transport Drop Force Shipboard Equipments
Features: The CUP MOUNT with combination of compression and shear load, Designed for integral fail safe mount. Protect from oil contamination Applications: Compressors Ship Board industrial & Vehicle engines Blowers
Prefabricated Rubber Running Track, composed of two different layers vulcanized together. The formulationof the top layer is different from that of the bottom layer. The vulcanization process guarantees molecular bond between the two layers. The end result is a continuous, seamless piece of material. The rubber-based top layer provides outstanding elasticity. The unique non-directional surface embossing, free of surface coatings and loose granules, provides greater contact area than other tracks surfaces, as well as greater water flow efficiency in rainy conditions. EPDM synthetic rubber vulcanization of the further strengthen of the materials of polymer, the good performance for Aging resistance, weather resistance, electrical insulation, corrosion resistance, impact resistance etc. Natural rubber has excellent properties of high elastic insulation, waterproof, low specific gravity, after appropriate treatment with alkali, heat, cold, pressure. Full solid be consistent from beginning to end, and has maximum compression deformation. Its advanced partition design maximizes absorption and recovery of energy. Application: for athletic field & athletic running track material of high school, university, physical college, sports center, stadium Certificate: IAAF Certificate, IAAF Class1st Athletic Facility Certifciate,ISO9001 and ISO14001 Installation: 1) Foundation requirements: asphalt, or, concrete. Using Scrapping machine to scrap the foundation very clean and very flat. Using Primer 0.2kg/m2 to brush on the foundation to avoid underground water rising and protect the running track system 2)Preparing installation tools, two components polyurethane adhesive, running track surface roll to start installation, installation of rolls should be from inner to outside, from straight runway to curve runway. 3)Lines marking after finishing installation of rolls Free samples !! After-sale service: Provide free training lesson for our oversea distributor or buyer, professional product & construction knowledge for you. WENDY TAM wendy@flysteptrack.com www.flysteptrack.com
Features: 1. water Solubility 2.Nonpollution 3.Short Construction 4.Moderate Thickness 5.Good Wear-Resistance 6.Weather Resistance 7.Water-proof 8.Slip Resistance 9.breathability and colorful
We are manufacturer of Silicone Rubber raw located in India. Product Name : Silicone Rubber Chemical Name : Polydimethyl-methyl vinyl siloxane Other Name : MVQ Silicon Rubber Molding Silicone rubber Extruded Silicone Rubber Silicone VMQ Chemical Formula : C9H24Si2(SiO)m+n SPECIFICATIONS APPEARANCE: Milky White,Slightly Yellow HARDNESS(SHORE±2) 40-70 Application Molding silicone rubber is used for industrial and civil silicon rubber stamping seals and miscellaneous parts. Extruder silicone rubber is commonly used in the industrial use of silicon rubber and the wire, cable and so on. Our History: As one of leader suppliers , we produce Raw Silicone Rubber . We are 30 years old company however established since 2000 certified under ISO 9001-2008
Chemical Name:N-Cyclohexyl-2-benzothiazole sulfenamide Molecular Formula:C13H16N2S2 Molecular Weight: 264.41 CAS NO:95-33-0 EINECS NO.: 202-411-2 Specification: Appearance Gray-white powder Gray -white granular Initial M.P. oC� 98.0 98.0 heating loss %� 0.30 0.30 Ash%� 0.30 0.30 Residues on sieve(150μm), % � 0.10 Properties:Gray-white powder (granule) with a little odor, no poison. The density is 1.31-1.34. M.P.: 98oC above. Soluble in benzene, boluene, chloroform, CS2, CH2Cl2 acetone, ethyl acetate, hardly soluble in alcohol, insoluble in water, gasoline, acid / alkali with lower concentration Application:CBS has excellent scorching property, high curing rate, high modulus of vulcanized rubbers, wide range of application. It is a sulfenamide accelerator with the highest activity in EPDM. Packing:25kg in kraft paper bag with PE bag inside. Storage:Stored in cool, dry and draughty place; avoid direct sunlight; protect against moisture or high temperature. The validity is 2 years.
Type: Single Type, Double Type, BSP/NPT Thread Type Size Range: DN25-DN1600 Material of Rubber ball: CR, NBR, EPDM, HYPALON, VITON Material of flange: Galvanized Steel, Stainless Steel Working temperature: -20â?? to +115â?? Ball length for Single Sphere: 130mm, 150mm, 95mm-300mm Ball length for Double Sphere: 175mm-345mm Ball length for Union Type: 200mm for DN15-DN50, 240mm for DN65-DN80. Thread End Connection: BSP or NPT thread Flange End Connection: EN1092-1 PN10/PN16, ANSI150, BS4504, AS2129 Table D/E. Working Pressure: PN6, PN10, PN16, PN25 Application: water, warm water, seawater, weak acids, alkalis, etc... Easy installation and remove; absorbs vibration, noise and shock -
Rubber products in materials such as EPDM, neoprene, silicone, viton
Description: the natural rubber sheet, gum rubber sheet are made by ROTOCURE vulcanizing press or plain vulcanizing press with high quality natural rubber(NR). The natural rubber is from the natural rubber tree with middling hardness and high tensile strength, high elongation, good abrasion resistance, elasticity, safety and nontoxicity without smell. The pure natural rubber sheet is also named gum rubber sheet or para rubber sheet. 1-6mm thickness is made by ROTOCURE vulcanizing press with shiny surface, 7-80mm thickness is made by vulcanizing press for get higher thick thickness. Working under the higher pressure, wearing resistant, food grade lining status at the temperature of -35°C - +85°C in air or water. Apply to punch all kinds of seals, gaskets, lining and others applications with its good function, for example of truck lining, drinking water lining, rubber membrane special for PVC vacuum laminating press. Specifications: material: pure natural rubber or NR/SBR quality: industrial grade, food grade color: black, white, brown, beige, red, green etc. surface: smooth/smooth, smooth/impression fabric, double impression fabric tensile strength: 2-24Mpa hardness: 35, 40, 50, 60, 70, 80+/-5shore A elongation: 170%-760% density: 1.05-1.70g/cm3 working temperature: -35°C - +85°C thickness: 1.0-50.0mm width: 0.1-3.6m length: 1.0-20m Insertion: reinforce to insert 1-3PLY fabric natural rubber lining sheet: top: cured natural rubber with red or black bottom: uncured neoprene rubber with light yellow quality: industrial grade, food grade surface: smooth/smooth tensile strength: 13-18Mpa hardness: 35, 40, 65+/-5shore A elongation: 400%-650% density: 1.05-1.15g/cm3 working temperature: -35°C - +85°C thickness: 1.0-25.4mm width: 1-1.5m length: 10-20m
