Pollution Control Equipments Suppliers and Manufacturers

About Steel re-Rolling Mill Steel Re-rolling is a major steel section and bar producing technology used in India and abroad. Since its inception in India with setting up of first re-rolling mill in Kanpur in 1928, this technology has contributed significant steelmaking capacity in secondary steel sector in India. Air Pollution Depending upon the fuel used in heating the furnace of a Steel Re-rolling Mill, the characteristics of flue gases may vary. For coal fired furnaces they may consist of gaseous as well as particulate pollutants. For oil or gas fired furnaces, these flue gases may consist of just gaseous pollutants. The flue gases may also be corrosive in nature. Selection of Technology for Air Pollution Control Device Selection of Technology for Equipment in an Air Pollution Control System in case of a Steel Re-rolling Mill depends upon the fuel to be used : a. Scrubber based System for Oil / Gas Fired Furnaces b. Cyclone and Scrubber based System for Coal Fired Furnaces About Scrubber based System for Oil / Gas Fired Furnaces Characteristics of Air Pollution Generated In Induction Furnace 1 Pollutants : Dust & Gases such as NO , SO , CO, Co x 2 2 2 Concentration : SPM - 1200-1500 mg/Nm (Maximum, in coal fired) 3 So - 800-1000 mg/Nm 2 4 NO - 20-50 mg/Nm x 5 Temperature : At Suction Point: 250-300 C 6 Nature of Dust : Slightly Sticky, Non Abrasive and Non Explosive Control Practices The control practice adopted in controlling air pollution in this industry mainly depends upon following parameters : 1 Dust/Gas Concentration at inlet 2 Discharge Standards 3 Temperature of Flue Gases 4 Nature of Pollutant i.e. Dust (Particulate) or Gaseous 5 Nature of Dust i.e. Sticky, Abrasive 6 Nature of Gases i.e. Corrosive, Non Corrosive Working of Equipment 1. Ducts & Bends : 2. Scrubber : 3. ID Fan : 4. Stack (Chimney) : About Cyclone and Scrubber based System for Coal Fired Furnace Working of Equipment 1. Ducts & Bends : 2. Cyclone : 3. Scrubber : 4. ID Fan : 5. Stack (Chimney) : Discharge Characteristics as Per Norms 1 Dust : Less than 150 mg/ Nm 2 Temp : Less than 80-100 C 3 Gases : Traces of SO , NO , Co , Co.

The Air Max is for intercepting all kinds of dirt coming into indoor from outside. By using HEPA filter.

This unit features a deep-bed activated carbon filter that uses a special carbon blend to remove voc's (volatile organic compounds) which are the most common airborne chemicals in the home. The unit also includes a medical-grade hepa to remove 99.97% of airborne particles (pollen, dust, mold, bacteria, viruses, pet dander) down to 0.3 microns in size Activated carbon filter, 2.5" depth, medical-grade hepa, pre-filter. 18 lbs. Or activated carbon. 50lbs

1. Lead smelting A.Mini blast furnace B.Rotary furnace 2. Refining pots for refining and alloying. 3. Ball mills for lead oxide. 4. Fugitive emission control system. 5. Continous casting machines with ingot and jumbo ingot moulds 6. Battery cutting machines 7. Battery crushing and hydro sepration. 8. Sewage and effluent treatment plant

About Rotary Furnace The Rotary Melting Furnace is a very flexible and universal equipment used for recycling many non-ferrous metals. It is the major lead production technology used in India and many other countries for Secondary Lead Production. A lead production system based on this technology has certain distinct characteristics such as: Equipment scalable for installing higher capacities Recovers all lead in one production cycle Plates & powder from scrap battery as well as slag from Mini Blast Furnace can be used as raw material Requires addition of certain consumables Can be fired with various fuels Generates high Pollution both as Flue Gases & Fugitive Emissions Description of Rotary Furnace It is a Rotary kiln in the form of a metallic cylinder with conical sides on both ends. Mild steel plate is used for construction of this shell and its thickness varies depending upon the capacity of the equipment. This shell is rotated on its own axis at 1-2 rpm. For this purposes tyres (also called riding rings) are fitted on the shell. These are fabricated from MS squares or flats, machined for a smooth finish. These tyres ride on steel rollers which are again machined finely. These rollers are fitted on a robust MS structural frame and driven by a gear & motor arrangement. The shell is lined inside with insulation and fire bricks of suitable Alumina content. Conical ends of the furnace are open on both sides. The furnace is charged with Raw material along with additives from the front end. This side is provided with a movable door on which a burner is mounted. The burner can be a conventional one or a fully automatic one depending upon the fuel used. At the other end, an exhaust block lined with refractory bricks is provided. A tapping hole is provided in the center of the shell from where molten metal & slag are discharged. Flue gases generated are sucked from the exhaust block side of the furnace. A typical 3.0 TpB Rotary Furnace has the following standard sizes & specifications : Outside dimensions of the Rotary Shell dia : 2075mm Shell length : 2500mm Total length : 4500mm Charging dia : 450mm Exhaust side dia : 450mm Refractory thickness : 200mm Fuel : Furnace Oil Burner : Model 4 A FD Fan capacity : 1250 cmh at 1000mm of WG Gear Box in drive : 8, 1:40 Ratio Motor in drive : 15.0 HP x 960 RPM Structure used for base : ISMC 250 x 80 Manufacturing Process Lead to be manufactured from Rotary Furnace can be obtained directly from scrapped batteries or as slag from Mini Blast Furnace. In case of former, batteries are cut open or broken to segregate lead scrap, plastic and other materials from them; lead scrap in the form of lead powder/ plates etc. is charged in the furnace along with a proportionate charge of additives. In the case of latter, slag produced from Mini Blast Furnaces is charged into the Rotary Furnace, again with proportionate additives. This process is a batch type process. After filling the required quantity of raw material (either manually or mechanically), the lid of the furnace at the front is closed. The burner attached to the moving door is then fired. Complete mass of lead raw. Material along with additive chemicals is heated at high temperature inside the furnace. After some time, molten lead is collected at the bottom of the furnace by puncturing the central opening of the Rotary Furnace. Lead is collected either directly into Jumbo Ingot Moulds or in receiving channels from which they are poured into Jumbo Ingot Moulds. After draining the Furnace of the first batch, production of next batch is undertaken and the Furnace is again charged with raw material. After three such batches, one batch of slag collected in Rotary Furnace is executed. This process leads to generation of flue gases which are toxic in nature and need appropriate and adequate Air Pollution Control System for their treatment. The steps of Charging and Tapping of Rotary Furnace also lead to generation of Fugitive Emissions which need to be captured at source and treated to maintain ambient air standards at workplace. Process Details of a typical 3.0 TpB Rotary Furnace Raw Material Charged3000 kgs/ Batch Total additive chemicals charged:400-500 kgs/ Batch Rotational speed1-2 RPM Fuel usedFurnace Oil Calorific value of fuel used8600 kCal/ kg. Fuel consumed30-40 lt/ hr. Air provided for process1250 cmh Lead produced9000-10000 kg/day (for Raw Material feed of 12-15 T raw material being lead powder and plates) Flue gas generation15000 cmh Section View of Rotary Furnace Advantages and Disadvantages of Rotary Furnace Advantages Recovers 100% lead in the first operation. Slag produced is lead free. Equipment can be scaled up for higher production capacities. Disadvantages Many chemicals are required for operation. High power consumption. Difficult to produce low Antimony lead suitable for soft lead purposes. Fugitive Emissions need to be captured in addition to flue gases. Need skilled operators and careful maintenance. Air Pollution Control Device for Rotary Furnace Apart from plates and paste of lead oxide from scrap batteries, slag from Mini Blast Furnace is charged in the Rotary Furnace. In addition to these, certain compounds of sulphur are also present in the batteries. When this material is heated in the presence of carbon, lead oxide is converted to lead. This conversion along with burning of fuel generates flue gases and fumes containing dust, dirt, oxides of lead, lead particles and such other impurities etc. Hence, to meet various goals of maintaining employees' health and factory environments as well as regulatory requirements, it becomes imperative to get high end Air Pollution Control Systems to be installed with the Rotary Furnaces. Characteristics of Air Pollution generated in Rotary Furnace Selection of Technology for Air Pollution Control System Based on the parameters and the standards mentioned, the following technology is adopted for Air Pollution Control System in Rotary Furnace: Rotary Chamber Gravity Chamber Involute Cyclone Pulse Jet based Bag House Filtration System Details of Equipments allow with Functions Rotary Chamber Rotary Chamber receives very hot gases from Rotary Furnace while cold gases from atmosphere are induced into chamber via specially designed profile. Thus chamber works as an equalizing chamber to reduce the temperature of gases and also where sedimentation of dust particulate matter takes place. Duct & Bends Ducts and Bends are required to convey flue gases from point of suction to final top of the chimney and connect various equipments like gravity chamber, cyclone, bag house, ID Fan and chimney. All bends and reducers are aerodynamically designed and have provision of manhole cleaning mechanism. Gravity Chamber It is a low pressure drop device which: Allows large size particles to settle down Cools down temperature of flue gases Used as spark arrestor to entrap live or red hot particles. Involute Cyclone Cyclone is used to remove medium size particles from flue gases stream. The treated flue gases are discharged from top and dust is collected at bottom. Bag Filtration System It is used for final filtration of flue gases to remove fine dust particulate matter using Pulse Jet Technology. Treated gases from all the bags are collected at top of bag house and passed through ID Fan to exhaust the same through chimney. The dust is collected at bottom of hopper and is discharged through Rotary Air Lock Valve. ID Fan ID Fan provides necessary driving force to convey flue gases from top of furnace to top of the chimney. The volume sucked overcome the total resistance offered by equipment and duct with the help of fluid horse power provided by ID Fan driven by suitable motor. Stack (Chimney) The generated gases are passed into atmosphere after treatment through chimney of suitable height and diameter. At the time of Delivery

About Lead Refining Lead recycled from used lead acid batteries or other sources (Secondary Smelting) via the Mini Blast Furnace or Rotary Furnace route, contains lot of contamination and undesired components. On the other hand, Lead required for battery manufacturing is either soft Lead with 99.97% purity or hard Lead of varying Antimony compositions. In order to make quality of lead suitable for its different uses, different variations of pot melting processes are employed. These include Re-Melting for removal of slag, Refining” for attaining required purity levels and Alloying for producing various alloys of lead. The equipments used are the same, the consumables and the processes, however, differ. Description of Melting Pot The Melting Pot (or Refining Pot or Alloying Pot, as it is variously called), is a mechanical mixing device with a pot and a heating arrangement. The inner pot is made of heavy MS plate with dish end bottom. It is placed within a jacket of refractory bricks, which in turn, are protected by an outer cover of MS plate with reinforcements. The pot is covered at the top with opening for feeding lead ingots and is provided with an electro-mechanical mixer. At the bottom, a heating source, usually an oil fired burner, is provided to heat the pot and to melt the lead. Once lead melts, impurities are skimmed and removed and any consumables required are added. Lead is then drained from the pot through an outlet pipe and valve. Capacity of such pots depends upon the requirements of particular units. Standard pot capacities made are from 4.0 TpB to 20.0 TpB. Higher capacity pots are also manufactured as required by any particular establishment. A typical 10.0 TpB Refining Pot has the following standard sizes and specifications: Diameter (ID) 1150mm Height 1250mm (Dish Depth of 200mm) Flange Width 350mm Outer Shell Diameter 1900mm Stirrer MoC & Dia SS-304 & 75mm Stirrer Motor 5.0 HP x 960 RPM Outlet Valve Size 40mm Burner Diesel Fired Fuel Consumption Range 8-18kg ltr Melting pots are installed both with and without accessories which may include Ingot Casting Machine, Ball Making Machine (where Ball Mills are installed down the line), Air Pollution Control Systems, Jib Cranes etc. Production Process Melting Processes have been grouped as Re-Melting Process Refining Process Alloying Process Re-Melting Process This process is undertaken for value addition to the recycled lead from furnaces. Lead is melted in the pot and major impurities are skimmed from it to make it saleable in the market. Refining Process Lead is melted in the pot, additives such as Sulphur, Wooden Powder and Coke Breeze are added and mixed gently followed by dross removal. Thereafter, Tin is added to remove Copper and temperature is increased to 550-6000C. Further, additives such as Sodium Nitrate & Caustic Soda are added to remove Antimony. This process is repeated to get the desired purity of lead. Alloying Process Lead is melted in the pot, additives such as Sulphur, Wooden Powder & Coke Breeze are added and mixed gently followed by dross removal. Thereafter, Tin & Antimony are added to the liquid metal to get the desired grade of Lead. Air Pollution Control Device for Refining Pot Melting processes lead to generation of air pollution at the following stages Initial heating and melting generates fumes Drossing with sulphur, wooden powder and coke breeze generates lot of smoke and dust particles Further heating for Refining and Alloying with different chemicals generates fumes and dust particles. Hence, to meet various goals of maintaining employees' health, factory environments as well as regulatory requirements, it becomes imperative to get high end Air Pollution Control Systems to be installed with the Melting Pots. Air Pollution Control Device for Refining Pot Dust : 500-600 mg/Nm Temperature : 60-80C G Gases : Fumes and Dust Discharge Characteristics required as per Norms Dust : Less than 50 mg/Nm Lead ( Pb) : Less than 10 mg/Nm Temperature : 50-60 C Gases : Not Detectable Selection of Technology for Air Pollution Control Based on the Parameters and the Standards mentioned, the following technology is adopted for Air Pollution Control System in Melting Pot: Pulse Jet based Bag House Filtration System Details of Air Pollution Control Device with functions Aerodynamically designed suction hoods are provided to capture flue gases generated at source itself. Duct & Bends Ducts and bends are required to convey flue gases from point of suction to final top of the chimney and connect various equipments like suction hood, bag house, ID fan and chimney. All bends and reducers are aerodynamically designed and have provision of manhole cleaning mechanism. Bag Filtration System: It is used for final filtration of flue gases to remove fine dust particulate matter using Pulse Jet Technology. Treated gases from all the bags are collected at top of bag house and passed through ID Fan to exhaust the same to chimney. The dust is collected at bottom of hopper and is discharged through Rotary Air Lock Valve. Bag Filtration System It is used for final filtration of flue gases to remove fine dust particulate matter using Pulse Jet Technology. Treated gases from all the bags are collected at top of bag house and passed through the ID Fan to exhaust the same through chimney. The dust is collected at bottom of hopper and is discharged through Rotary Air Lock Valve. ID Fan ID Fan provides necessary driving force to convey flue gases from top of furnace to top of the chimney. The volume sucked overcome the total resistance offered by equipment and duct with the help of fluid horse power provided by ID Fan driven by suitable motor. Stack (Chimney) The generated gases are passed to atmosphere after treatment through chimney of suitable height and diameter. At the time of Delivery

Ingot casting machine An ingot casting machine (continuous ingot caster) is a chain conveyor based mechanical arrangement which is used for easier handling of molten lead from melting pots. It leads to hassle-free casting of lead into ingots with minimum human contact and keeps this process safe, clean and fast. It is a custom made device suited for particular capacity required by user. The size of ingot to be casted can also be varied. Further, in special cases, even subdivision of ingots into smaller shapes is possible for suitability of usage. The output of a melting pot needs to be synchronized with the speed of the conveyor. A rotary distributor drum continuously receives the molten metal and pours it into ingot moulds below it. The ingot moulds are fastened on a chain conveyor that continuously moves in a loop. A robust frame of ms is provided for fitting of this conveyor alongwith sprockets, shafts and geared motor based drive. There is a water jet based cooling arrangement mounted on the frame itself which helps cooling down of the metal in the mould. It is provided with a mechanical knocking arrangement at the end of line for 100% knocking of ingot from the mould. These can be further supplemented with provision of multiple cooling lines, water re-circulation system, gas burners for drying up moulds, fumes collection hoods and discharge end conveyors. Note: due to continuous up-gradation in technology, specified & projected values may differ in actual products

Offers air pollution control equipments including air pollution control equipment like industrial air handling equipments, dust control equipments, dust collection systems, multiclones, cyclones, bag filters, centrifugal fans & blowers, ventilation fans, pneumatic conveying systems, wet scrubbers, fume extraction & filtration system, cartridge type dust collectors and accessories like rotary air lock valves, filter bags, cages, screw conveyors, gas cooter and air processing systems by manufacturer of air pollution control systems, Techflow Enterprises, Ahmedabad, India.

It's a water based paste which can efficiently isolate the staining on printing paste that caused by foiling. Appearanceígmilky white to transparent paste Main ingredientsígmacromolecular polymer and water. Ph value gneutral. 30kgs drum.

Reinforced Frame: Strong structure for outdoor movement. Water Tank: Work without constant water supply. Rotational Fan: Horn-shape fan concentrates the air flow. Adjustable wind velocity and height enlarge the working area for different environments. Float Valve: Automatic water supply controller inside the water tank. Drought Switch: Automatic shutdown and alarm to protect the pump when water tank is dried out. Overload Protector: Automatic shutdown to prevent damage of motor when current is overloaded. TEFC Pump Motor: Totally enclosed motor ensures electric safety from moisture. TEFC Fan Motor: Totally enclosed motor prevents danger caused by moisture. Model: Air-16L Output: 5 nozzles Pressure: 1000 PSI (70 BAR) Horsepower: 1/3 HP 18' rotating fan (3 speed) Dual filtration system Voltage: 110V/60Hz; 220V-50Hz/60Hz RPM: 1450 / 1750 Dimension: 78 x 63 x 157~208 CM Weight: 58 KG

Reinforced Frame: Strong structure for outdoor movement. Water Tank: Work without constant water supply. Rotational Fan: Horn-shape fan concentrates the air flow. Adjustable wind velocity and height enlarge the working area for different environments. Float Valve: Automatic water supply controller inside the water tank. Drought Switch: Automatic shutdown and alarm to protect the pump when water tank is dried out. Overload Protector: Automatic shutdown to prevent damage of motor when current is overloaded. TEFC Pump Motor: Totally enclosed motor ensures electric safety from moisture. TEFC Fan Motor: Totally enclosed motor prevents danger caused by moisture. Model: Air-16L Output: 5 nozzles Pressure: 1000 PSI (70 BAR) Horsepower: 1/3 HP 18' rotating fan (3 speed) Dual filtration system Voltage: 110V/60Hz; 220V-50Hz/60Hz RPM: 1450 / 1750 Dimension: 78 x 63 x 157~208 CM Weight: 58 KG

Technical specification Combustion chamber outputú¦ 11.6KW Fuel consumptionú¦ 1.5L/H Solution outputú¦ 8-42L/H Fuel tank capacityú¦ 1.2L Solution tank capacityú¦ 6L weight(empty) 8.5kg Power supplyú¦ DC6V(4x1.5V) L*H*W: 125*29*35(cm)

Air pollution control equipment.

Product feature 1. The high pressure of the pump makes it possible to use spraying nozzles that have relatively large bores so that even wettable powder spraying mixtures can be appiled without any problems. 2. All the parts get in contact with chemicals are made form anticorrosive materical. 3. Equip with an adjustable output of 0-36l per hour, could adjust the flow rate to supplying for ultra-low-volume or low-volume spraying, this versatile gives you the power to handle both large and small areas, wherever the ulv aerosol generator is needed. 4. Equip with a flexible with handle on nozzle permits spraying into normally inaccessible and hard to reach aeras such as under/between kitchen cabinets, under carpets and above ceilings. 5. Large-caliber solution tank cover, easy to add chemical solution. 6. 6l solution tank, large volume solution tank, could load more chemical solution. Product specification/models 1. Electrial motor: 800w 220vac/50hz 2. Fogging nozzle: four counter-rotating vortex nozzles 3. Partical size: 5-50 micro vmd, adjustable. 4. Liquid flow rate in l/h: 0-36 adjustable 5. Tank capacity in l: 6 6. Dimensions in mm(lxwxh): 450x220x300 7. Weight in kg, empty: 4.2 8. Dimensions in mm(lxwxh)(shipping data): 445x230x360 9. Weight in kg, empty(shipping data): 5.2

Product feature 1. We produce this product in our high quality standard using only high materials, i.E. Stainless steel. 2. Its working performance is very reiable, you could spary at any angle, the engine will not flameout. 3. High-work-efficiency, economical, the penetration and clinging of the fog is well. 4. Most light in weight, it is easy to operation and maintenace. Product specification/models 1. Weight, empty in kg. Approx: 7.9 2. Deminsions in mm(lxmxh): 1440x270x315 3. Weight, empty in kg. Approx(shipping data): 11.6 4. Deminsions in mm(lxmxh(shipping data): 1288x310x360 5. Solution tank capacity in l: 5 6. Fuel tank capacity in l: 1.5 7. Fuel consumption in l/h, approx: 1.5 8. Performance of combustion chamber in kw/hp: 11.6/15.8 9. Maxinium flow rate in l/h: 42 10. Flow rate of oil in l/h, approx: 8~42 11. Energy: 2x1.5v batteries 12. Pressure in the solution tank in bar, approx: 0.25 13. Pressure in the oil tank in bar, approx: 0.06

Product feature 1. Excellent conformation, working performance is very reliable. 2. Low noise, ease of operation and maintenance, starting up immediately. 3. Fogging tube adopts two-stages cooling system, lower the temperature of the fogging tube and combustion chamber, ensure the unit will have a longer lifespan. 4. Adopts the automatic ignition system, ease of start up the unit. 5. The adjusting knob of oil nozzle has scalar, ease of operation. 6. Adopts anti-slide solution cap, ensure it is safe to the operator. 7. The fuel consume is low, it is up to 1 l/h. Product specification/models 1. Weight, empty in kg. Approx: 7.5 2. Deminsions in mm(lxmxh): 1330x290x315 3. Weight, empty in kg. Approx(shipping data): 11.5 4. Deminsions in mm(lxmxh)(shipping data): 1288x310x320 5. Solution tank capacity in l: 5 6. Fuel tank capacity in l: 1.5 7. Fuel consumption in l/h, approx: 1 8. Performance of combustion chamber in kw/hp: 11.6/15.7 9. Maxinium flow rate in l/h: 10 10. Flow rate of oil in l/h, approx: 10 11. Energy: 2x1.5v batteries 12. Pressure in the solution tank in bar, approx: 0.25 13. Pressure in the oil tank in bar, approx: 0.06

Product Feature The TS-36P utilizes high-power pulse-jet engine to producing a high output of dense heavy thremal fog for control of virus or flying insects such as mosquito, gnats, house flies, sand flies and black flies. 1. It can be disassembled withour extra instrument, it's easier of maintenace. 2. Fogging tube is eqipped with two-stage cooling system. This technology will greatly lower the temperature of the fogging tube and combustion chamber. 3. High-work-efficiency, economical, the penetration and clinging of the fog is well. 4. Most light in weight and with compact dimensions,it is easy of opearation. 5. Adopting refactory stainless steel to making the fogging tube, it will maintain its natural color and sharp in the whole years of its lifespan. 6. Equipped with 4x1.5 dry battery power supply to assure greater reliability. 7. Equipped with automic ignition system to assure ease of start-up the engine. 8. The adjusting knob of the oil nozzle has scalar, ease of operation. 9. could choose the auto-cut solution valve. In case of engine flameout, ensure it is safe to operator. 10. could choose the automatic ignition system of the air-pump, you only need to push down the start button, the machine will start-up immediately. Product Specification/Models 1. weight, empty in kg. approx: 8.1 2. deminsions in mm(LxMxH): 1375x290x360 3. weight, empty in kg. approx(shipping data): 13.1 4. deminsions in mm(LxMxH)(shipping data): 1270x310x370 5. solution tank capacity in L: 7 6. fuel tank capacity in L: 1.5 7. fuel consumption in L/H, approx: 1.5 8. performance of combustion chamber in KW/HP: 18.5/25.15 9. maxinium flow rate in L/H: 42 10. flow rate of oil in L/H, approx: 8~42 11. energy: 4x1.5V batteries 12. pressure in the solution tank in bar, approx: 0.25 13. pressure in the oil tank in bar, approx: 0.06

Product feature: 1. Producing nearly invisible small droplet, better penetration, quick infusibility. 2. Producing 90% of droplets are less than 15 micron in diameter, these small droplets will float in the air for a longer time before it subside to the ground, so this small droplet of chemical solution have a lasting effect for flying insects or virus in the air. 3. Adopting chemical resistant polyethylene to making solution tank, could dispense both oil based or water based chemical solution. 4. Rugged design handles corrosive liquids and heavy impacts. 5. It is ideal for increasing humidity and dispensing sanitizers, the durable plastic body is made from rugged chemical resistant polyethylene for years of trouble free operation. Both oil based and water based solution can misted through the non-clog nozzle. 6. Equipped with a precision regulating valve with scalar in the nozzle head to adjusting the flow rate, in order to get the desired size of droplets. 7. Solution tank is marked with capacity scale, so it is helpful when you add precise volume of solution. 8. Most light in weight, equipped with fabric strap, its length is adjustable, ease of operation. 9. With an adjustable output of 0-24l per hour, could adjust the flow rate to applying for ultra-low-volume or low volume spraying, this versatile unit gives you the power to handle both large and small area, wherever the ulv aerosol generator is needed. Product specification/models 1. Electrical motor: 800w 220vac/50hz 2. Fogging nozzle: four counter-rotating vortex nozzles 3. Chemicals: handles both oil and water based chemical solution. 4. Liquid flow rate in l/h: 0-24 adjustable 5. Tank capacity in l: 6 6. Dimensions in mm(lxwxh): 420x200x290 7. Weight in kg, empty: 3.1 8. Dimensions in mm(lxwxh)(shipping data): 445x230x360 9. Weight in kg, empty shipping data): 4.1

Pass box with air shower Standard export packing, 40kgs.