Granular activated carbons are made from rigid raw materials, giving the necessary hardness to avoid excessive losses due to attrition and handling. They present large internal surface of pore structure, ensuring high adsorption power in specific purposes and uses. They are used in fixed or moving beds as columns where the liquid or gas passes through and gets purified. They can be used in liquid or gas phase continous adsorption process and offer unusual economy in cases where carbon regeneration is favorable. In liquid phase applications they remove colloids and organic substances that give undesirable odors, colors and taste to the products. They are efficiently used for water dechlorination in processes which require super chlorination as well as the removal of organic substances from the water. In vapor phase application they participate in the solvent recovery, adsorption of colors, purification of carbon di-oxide and catalyst support. They are also used to reduce the COD and BOD in effluent waste water. Granular activated carbon is produced from coconut shell charcoal by the process of steam activation. The coconut shell charcoal is fed into the rotary kiln and activated by steam at high temperatures resulting in the evaporation of impurities and opening up of pores on the surface. The resultant big particles are then crushed and sieved to get the desired particle size. Our main grades of granular activated carbon are given as under. We can customize the iodine value as well as the particle size according to your requirements
Our Powder activated carbon is manufactured using pure pine wood which is an excellent base for manufacturing activated carbons with good adsorption power. The steam activated process is done by activating the charcoal in a rotary kiln by heating at high temperatures by steam. The activated carbon that comes out from the kiln is called unwashed activated carbon. These unwashed activated carbon has higher ash and iron content. This is reduced by washing the unwashed activated carbon with acid (HCl / H2SO4) and purified water. This results in reduction of ash content to as low as 1% and iron as low as 50 ppm. The gradation of different qualities of activated carbon is done on the basis of Methylene blue value and iodine value. The iodine value is a better test as the particle size of iodine molecule is small enough to penetrate the smallest of pores. We can relate the iodine value of activated carbon directly to its surface area because of the above fact.
Granular activated carbons are made from rigid raw materials, giving the necessary hardness to avoid excessive losses due to attrition and handling. They present large internal surface of pore structure, ensuring high adsorption power in specific purposes and uses. They are used in fixed or moving beds as columns where the liquid or gas passes through and gets purified. They can be used in liquid or gas phase continous adsorption process and offer unusual economy in cases where carbon regeneration is favorable. In liquid phase applications they remove colloids and organic substances that give undesirable odors, colors and taste to the products. They are efficiently used for water dechlorination in processes which require super chlorination as well as the removal of organic substances from the water. In vapor phase application they participate in the solvent recovery, adsorption of colors, purification of carbon di-oxide and catalyst support. They are also used to reduce the COD and BOD in effluent waste water. Granular activated carbon is produced from coconut shell charcoal by the process of steam activation. The coconut shell charcoal is fed into the rotary kiln and activated by steam at high temperatures resulting in the evaporation of impurities and opening up of pores on the surface. The resultant big particles are then crushed and sieved to get the desired particle size. Our main grades of granular activated carbon are given as under. We can customize the iodine value as well as the particle size according to your requirements
Wood Based Powder Activated Carbon is used for decolorizing in sugar liquors, juices,soybean and food industries. Wood powder activated carbon is non-toxic, without taste and it has the appearance of a fine black powder. Mb Value : 140 to 320 Ash:7 to 12%
Coal based activated carbon originates from coal that has undergone a steam activation process Coal based carbon has mainly mesopores and macropores and is very popular in gas phase purification portable water purification wastewater purification and aquariumpond water purification applications The carbonaceous product of wood Applications Gas phase purification Water purification system
Coconut shell activated carbon is derived from coconut shells. It has a very high hardness and is more abrasion resistant than any other type. It is a totally natural, environmentally friendly product that has a very small carbon foot print. The carbonaceous product of coconut. Applications â?? Portable water purification Wastewater purification Gold absorption from gold solution Medical use
Russian Mazut M100 is a fuel oil that is manufactured to GOST specifications, GOST 10585-75 (not active), GOST 10585-99 Oil fuel (GOST is the Russian system of standards, much like ASTM, for example). Mazut is almost exclusively manufactured in the Russian Federation, This kind of oil is graded as the heavy furnace oil. The product is produced from the remains of raw oil processing. This kind of mazut is produced only from the low sulphur raw oil. This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration (not the only consideration) when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product is considered a product, and because viscosity drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: Very Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Normal Sulphur is a Mazut M100 with a Sulphur content of 1.0-2.0% High Sulphur is a Mazut M100 with a Sulphur content of 2.0-3.5% The amount of sulfur affects how clean the oil burns, and in turn the emissions it creates, as well as the amount of buildup that accumulates within the engines and furnaces that burns it. M100 prices are often determined by its point of origin and mode of production. Apart from shipping charges and regulations, product quality is considered to be more essential. When petroleum is distilled, fuel oil is produced as a residue or distillate. Any fuel oil is a form of petroleum that is burned to produce energy or heat for running an engine. These are usually low-quality oils that are heated in a furnace or boiler and used in a number of industries. MAZUT is such fuel and is typically used in generating plants and factories. Of course, different plants have expected requirements and specifications of their fuel and this is why MAZUT M100/99 and GOST 10585-75 are produced according to industry ISO standards.
Aviation Jet Fuel is a type of aviation fuel designed for use in aircraft powered by gas-turbine engines. It is colourless to straw coloured in appearance. The most commonly used fuels for commercial aviation are Jet A and Jet A1, which are produced to a standardised international specification. The only other jet fuel commonly used in civilian turbine-engine powered aviation is Jet B, which is used for its enhanced cold-weather performance. Jet fuel is a mixture of a variety of hydrocarbons. Because the exact composition of jet fuel varies widely based on petroleum source, it is impossible to define jet fuel as a ratio of specific hydrocarbons. Jet fuel is therefore defined as a performance specification rather than a chemical compound. Aviation Jet Fuel is commonly referred to as JP54. However, this is the wrong terminology as there is no such grade of Jet Fuel. Jet A and Jet A1 are what refineries offer. Aviation Jet fuel Gas is what powers turbine aircraft engines. Worldwide, Jet Fuel is the most used low Sulphur content Kerosene. For instance, Colonial JP54 is similar to Jet A except the energy is 18.4 mj/Kg compared to the 42.8 MJ/kg of Jet A. Most importantly there is also a slight difference in additives. Aviation Jet Fuel B is used for its extremely cold weather performance. However, aviation Jet fuel Bs lighter composition makes it more dangerous to handle. For this reason, it is rarely used except in very cold climates. A blend of approximately 30% Kerosene and 70% Gasoline. Because of its very low freezing point (60 C (76 F), it is known as a wide cut fuel and has a low flash point as well. Aviation Jet Fuel B is primarily used in some military aircraft. In Canada, it is also used because of its freezing point. Aviation Kerosene standards are published as GOST10227-86. The standard consists of different properties. It separates paraffin and gasoline in the refinery. Military organisations around the world use a different classification system of JP (for Jet Propellant) numbers. Some are almost identical to their civilian counterparts and differ only by the amounts of a few additives. For instance, Jet A1 is similar to JP 8, Jet B is similar to JP 4. Military fuels are highly specialised products and are developed for very specific applications. Jet fuels are sometimes classified as kerosene or naphtha type. Kerosene type fuels include Jet A, Jet A1, JP 5 and JP 8. Naphthatype jet fuels, sometimes referred to as wide cut Jet Fuel, including Jet B and JP 4.
Petroalliance is a professional supplier for all kinds of coke products. Such as Semi coke, metallurgical coke, Foundry coke, Petroleum coke , Pitch coke and so on. We can provide different quality products according to the needs of our customers. We are trying to deliver a superme service for our customers including any packing orders, transportation and technical support. The company has get the dangerous chemicals business license and ISO 9001 certificate. Our product, service and manufacture have been kept high quality, good performance and environmental friendly all the time. We would have put lots of efforts on high quality products and services to keep a good relationship with our customers.
Product Name: High Preessure Industrial Use Transformer Vacuumizer Packaging Wxf Series Anti-Explosive Oil Free Rotary Vane Vacuum Pump Summary: We have more than 20 types chemical process pump, such as horizontal pump, submersible pump ,vertical pump, semi-submersible pump, fluoroplastic pump, axial pump ,gear pump.ect . Application: They are used for transmission of liquids (oil, sea water ,sulphuric acid, phosphoric acid, H2SiF6acid, alkali liquid) with low or high temperature, neutral or corrosive liquids ,or liquids with solid granular and widely used in petroleum chemical industry ,oil refining industry, paper ,pulp industry ,sugar industry ,mining ,etc Lots of material can be chose for different working condition, such as cast steel ,stainless steel 304,316,2205,904L, Hartz alloy C276,C22, nickel-base alloy GH600, PVDF,PP, UHMWPE-lining .etc Pump a strong seal system :packing seal ,double face mechnical seal ,cartridge mechnical seal ,API682 flushing syestem.
Uses of base oil sn500 Base oil sn500 use in manufacturing of many lubricants oil , who produce base oil mostly use sn500 as additive in their other product also blenders and compounders are other user of base oil different grades as well as sn500 , mostly base oil add from 1% up to 20% as additive to other products . base oil use in different oil as well is engine oil , motor oil , hydraulic oil , gear oil etc.
Petroalliance is a professional supplier for all kinds of coke products. Such as Semi coke, metallurgical coke, Foundry coke, Petroleum coke , Pitch coke and so on. We can provide different quality products according to the needs of our customers. We are trying to deliver a superme service for our customers including any packing orders, transportation and technical support. The company has get the dangerous chemicals business license and ISO 9001 certificate. Our product, service and manufacture have been kept high quality, good performance and environmental friendly all the time. We would have put lots of efforts on high quality products and services to keep a good relationship with our customers.
Russian Mazut M100 is a fuel oil that is manufactured to GOST specifications, GOST 10585-75 (not active), GOST 10585-99 Oil fuel (GOST is the Russian system of standards, much like ASTM, for example). Mazut is almost exclusively manufactured in the Russian Federation, This kind of oil is graded as the heavy furnace oil. The product is produced from the remains of raw oil processing. This kind of mazut is produced only from the low sulphur raw oil. This product is typically used for larger boilers in producing steam since the BTU content is high. The most important consideration (not the only consideration) when grading this fuel is the sulfur content, which can mostly be affected by the source feedstock. For shipment purposes, this product is considered a dirty oil product, and because viscosity drastically affect whether it is able to be pumped, shipping has unique requirements. Mazut is much like Number 6 Oil, and is part of the products left over after gasoline and lighter components are evaporated from the crude oil. The main difference between the different types of Mazut-100 is the content of sulphur. The grades are represented by these sulfuric levels: Very Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Low Sulphur is Mazut M100 with a Sulphur content of 0.5% Normal Sulphur is a Mazut M100 with a Sulphur content of 1.0-2.0% High Sulphur is a Mazut M100 with a Sulphur content of 2.0-3.5% The amount of sulfur affects how clean the oil burns, and in turn the emissions it creates, as well as the amount of buildup that accumulates within the engines and furnaces that burns it. M100 prices are often determined by its point of origin and mode of production. Apart from shipping charges and regulations, product quality is considered to be more essential. When petroleum is distilled, fuel oil is produced as a residue or distillate. Any fuel oil is a form of petroleum that is burned to produce energy or heat for running an engine. These are usually low-quality oils that are heated in a furnace or boiler and used in a number of industries. MAZUT is such fuel and is typically used in generating plants and factories. Of course, different plants have expected requirements and specifications of their fuel and this is why MAZUT M100/99 and GOST 10585-75 are produced according to industry ISO standards.
For latest pricing Enquiry., Please contact US via email and contact details
For latest pricing Enquiry about all kind of petroleum products., Please contact US via our email and contact details
Natural gas with delivery Hub Baumgarten - AUSTRIA /EUROPE /or Turkish measurement centers The contract amounts to 5 billion m3 per year. The following documents are required to submit an application: - Agreement with a hub or Turkish settlement unit. - Full CIS company. -LOi - Consumer list. All documents must be from the same company and for the same company. Documents prepared on the basis of a partnership agreement from different companies are not accepted. The procedure and the complete package of documents will be provided to the buyer or his official representative. Only scanned documents are accepted.
Jet A-1 Fuel - Power Your Journey with Unmatched Reliability! Our Jet A-1 Fuel is formulated to meet the rigorous standards of the aviation industry, ensuring peak performance at high altitudes. Designed for modern aircraft, it offers a perfect blend of efficiency and safety, providing a smooth flying experience. Choose reliability and excellence for your aviation needs.
Residue Wax also known as foot oil is a byproduct obtained during the production of semirefined paraffin wax It contains oil content that prevents it from being solid at room temperature Residue wax is used in various applications including the rubber industry shoe polish formulations and in making various protective coatings
Rubber Process Oil (RPO) is a category of oil used to produce various rubber compounds, enhancing their workability and extending their physical properties. It acts as a plasticizer, reducing the mix viscosity, and improving the dispersion of fillers. RPO is critical in manufacturing tires, rubber sheets, and other rubber products contributing to the elasticity and strength of the final product.
Paraffin Wax, A refined and solid wax derived from petroleum, coal, or oil shale. Known for its excellent insulation properties and low reactivity, paraffin wax is extensively used in candle making, coating for waxed paper or cloth, and in cosmetics such as cold creams and ointments.
