Calomi Bamboo charcoal environmental protection wall paint can combine with purified air ,anti formaldehyde, benzene ect , release negative ions ,anti mildew& bacterial ,scrub resistant ect different functions together , which is your best choice for high quality life.
Product Features:
1. Upgrade purified smelling technology
2. Anti formaldehyde ,and benzene ect
3. Cover small crack
4. Long life time and bright
5. Excellent cover power
6. Anti mildew and bacterial
? maximum load :20kg/b
? minimum cycle time :180sec
? average cycle time :240sec
? maximum basket output :20b/h
? average basket output :15b/h
? maximum prodution :400kg/h
? average prodution :300kg/h
I am the coating and paints for construction building supplier. Our factory is in Germany, we have the all document and certification in Europe. If you have the interest.
SAFFRO'S aura Premium Gloss Enamel gives smooth,hard & glossy finish.Its dry film has good adhesion to the surface.It has very good flow and brushability. aura Premium Gloss Enamel is a highly washable paint, thus you can wipe off most common household stains easily
RECOMMENDED USE It is applied on furnitures,drums,barrels,household products,elecrical
motors,doors,windows and variety of other surfaces which are not
subjected to outdoor exposure
FINISH :smooth and glossy
COLOR As per shade card Including White and Black.
COVERING CAPACITY :7 to 9 sq.mt/lit/coat at 30 to 35 micron dry film thickness,depending
(ON SMOOTH MILD STEEL SURFACE) upon shades and surface.
DRYING TIME :Surface dry - Less than 3 hours.
:Hard dry - Less than 15 hours.
Second coat application period -After 10 hours
Above all properties depend upon temperature and humidity.
FLASH POINT :Above 30* C (86 *F)
THINNER RECOMMENDED :SAFFRO Synthetic G.P Thinner
METHOD OF APPLICATION :By Brush or spray at a pressure of 40 to 50 P.S.I
RECOMMENDED PRIMER :For Metal - SAFFRO R/O Z/C metal primer
- SAFFRO Zinc Chrome primer yellow
For Wood - SAFFRO Wood primer white
For Plaster - SAFFRO Cement primer (oil base)
DIRECTION FOR USE Remove dust,grease,oil,moisture,rust and other loose flakes etc.After
priming the surface with recommenden primer with over night drying &
sanding with emery paper,apply SAFFRO SHINE synthetic enamel using
recommended thinner.Allow first coat to dry for minimum 10 hours before
applying second coat.Stir the content thoroughly prior to use
BUILDER COAT Acrylic Interior | Exterior emulsion is matt finish.
FEATURES :-
BUILDERCOAT Acrylic INTERIOR | EXTERIOR emulsion provides a smooth long lasting rich finish to the INTERIOR & EXTERIOR wall. It is washable and most stain can be removed easily by sponging with mild soap solution. The paint film is having good resistance to fungus and mildew.
RECOMMENDED USE :-
BUILDERCOAT Acrylic INTERIOR / EXTERIOR emulsion is INTERIOR / EXTERIOR wall finish that can be applied on all type of smooth plaster, asbestos sheets, concrete etc.
PRODUCT TECHNICAL DATA :-
COLOURS : White & other shades
FINISH : Smooth and Matt
COVERAGE : On smooth primer masonry surface by brushing
1 coat: 130-160 sq. ft/ltr
2 coats: 80-90 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc)
DRYING TIME : Surface drying time â?? 10-15 minutes
GLOSS LEVELS/SHEEN LEVELS : Matt
FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable
SUITABILITY OF THINNER PAINT Use within 24 hrs.
SHELF LIFE 18 months from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The low solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance.
Recommended Use :-
It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc.
Physical Data
COLOUR : Selected industrial shades
FINISH : Semi glossy
SOLIDS BY VOLUME : 80 + 2%
THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80
FLASH POINT : Base : Above 25C Hardener : Above 25C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data :-
MIXING RATIO : Base : Hardener ( As per our recommendations)
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Epoxy Thinner 190
RECOMMENDED DFT : 75-100 mic.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data :-
COLOUR :- Yellow
FINISH :- Matt
SOLIDS BY VOLUME :- 40 �± 3%
THEORETICAL SPREADING RATE :- 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT :- Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) :- SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE :- BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data
MIXING RATIO :- Base : Hardener (As per our recommendation)
APPLICATION :- By Brush / By Conventional Spray
THINNER :- Type 290
POT LIFE :- 3 hours min at 30�° C
RECOMMENDED DFT :- 30-40 �µ.
OVERCOATING INTERVAL :- MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY :- Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application.
For Conventional Spray application :-
Thinner : Type 290
Addition : 10-15%
Nozzle Orifice : 1.2 -1.4 mm
Nozzle Pressure : 40-70 p.s.i.
For Airless Spray application :-
Thinner : Type 290
Addition : Max 5%
Nozzle Orifice : 0.28- 0.37 mm
Nozzle Pressure : 1400-1800 p.s.i.
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
6500 Paints Coatings Suppliers
Short on time? Let Paints Coatings sellers contact you.
