Plative ISP3320 anodizing protective paint Brief description Plative ISP3320, a kind of antioxidant protective paint, is specialized applied to anodizing treatment. Strong acid resistance such as hydrofluoric acid, concentrated sulfuric acid. Good adhesion. Good leveling Operational guidance First, to clean and dry the surface, no oil slicks, no dust. Second, to paint the surface where prevent from plating or pickling next (the corresponding additives can be used to dilute the product) painting by screen printing, pad printing, scratch, dipping, or spraying. Then 160-200heat cured in 20-30 minutes. To clean the coating with the corresponding removers after anodizing. Annotation Considering the painting method, please dilute the product to appropriate viscosity before use please use the corresponding thinners, or else it could lead to paint deterioration; during operation, please keep the environment ventilation to prevent inhalation. Plative ISP3320 anodizing protective paint brief description Plative ISP3320, a kind of antioxidant protective paint, is specialized applied to anodizing treatment. Strong acid resistance such as hydrofluoric acid, concentrated sulfuric acid Good adhesion. Good leveling operational guidance First, to clean and dry the surface, no oil slicks, no dust. Second, to paint the surface where prevent from plating or pickling next (the corresponding additives can be used to dilute the product)painting by screen printing, pad printing, scratch, dipping, or spraying. Then 160-200heat cured in 20-30 minutes. To clean the coating with the corresponding removers after anodizing. annotation Considering the painting method, please dilute the product to appropriate viscosity before use; please use the corresponding thinners, or else it could lead to paint deterioration; during operation, please keep the environment ventilation to prevent inhalation.
It is used for strain a paint it manufacture from nylon net fabric. Packet of 12 bags 42 packet in a box
High quality lightweight polyester putty for car repairs – latest technology in putties. - Creamy texture. - Very low density. - Extremely easy to mixing and apply. - Exceptional sanding quality. Color - Light Blue. Gloss Grade – Matt. Density – 1,00 kg/l.
Clear coat can be put on: 1. Basic colours, 2. Existing Paintwork in sound condition Existing paintwork should first be dried, abraded and cleaned with a silicone remover. For dulling the colour we recommended the following: - grey unwoven abrasive fabric with dulling paste -abrasive paper with gradiation of 600 to 8000 (for Dulling wet), - abrasive paper with gradation of 360 to 400 (for dulling by machine).
IT 2007 varnish is two component acryic transparent lacquer with low content of volatile components. it is intended to profession use, in the 2:1 system. Hs Varnish creates the hard coat with the brillinat polish and fits for lacquer finishes of cars after all types of repairs. standard packing - 1L and 5L.
Coil coating paints suitable for all substrates and all coating lines. 200 liter ms drums.
1. Simple to apply and to repair 2. Long term good looks and low maintenance 3 .Ready to use,just add water 4. DIY eco-friendly paint. Inner plastic package,1kg/bag.
Name: water-based varnish (self-adhesive) Model: H-5803C Use: for in-line printing , wet to wet printing , self-adhesive , for noodles package . Description: H-5803C is a plus by a special acrylic polymer emulsion with functional additives varnish, It has strong adhesion for the paper after it was hot of the Ultrasonic heating. This varnish has excellent gloss, good gloss and color retention, dry fast, good printability. The wet-wet and wet-dry printing has good wetting leveling, strong anti-alcohol ,printing machine is easy to clean. Dedicated to the noodles package(such as Master), which need ultrasonic to glue Automatic .This varnish is used off-line coating, can also be used for inline coating. Appearance: milky white liquid, Solid content 40%, Viscosity (seconds): 18 ~ 20, (3 cup, 25 ), Gloss: 55 5 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70 . 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. Package: 25KG/50KG/120KG plastic containers, sealed in a cool place, the shelf life is one year.
Name: water-based varnish (in-line) Model: H-5303C Use :for in-line printing , wet to wet printing , matt ,for paper package . Description: H-5303C is an environmentally friendly oil dumb fast printing, excellent wear resistance, good leveling characteristics. Fast drying and good printability. Wet ink on good wetting leveling, strong resistance to alcohol, printing machine is easy to clean. Used for frozen packaging, bottled instant noodles, electrical appliances, wine packaging and other high-end printing cigarette packaging. This varnish coating for offset printing blanket, inline coating, glazing, and off-line flexo coating. Appearance: milky white liquid, Solid content 40%, Viscosity (seconds): 18 ~ 20, (Viscosity Cups 3 , 25¡æ) Gloss: 6 ~10 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70. 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. 25kg/50kg/120kg plastic containers.
Name: Water-based Varnish (high viscosity) Model: H-5312 Use : high gloss ,high viscosity ,for paper package printing Description: H-5312 is an environmentally friendly water-based varnish, excellent wear resistance, high gloss, gloss retention, dry fast, good printability. A variety of ink has good wetting leveling, printing machine is easy to clean s. It is meet the national and EU environmental standards, through the EU ROHS test, compliance with international environmental requirements. Scratch resistance is strong, mainly used for dusting and more printing, high wear resistance. Appearance: milky white liquid, Solid content: 461%, Viscosity (Viscosity Cups 3 , 25 seconds): 18 ~ 20, Gloss: 4 ~ 7 Notes: 1, It based on conditions of use plus appropriate diluent (water) or alcohol and water (1-5:1) mixture dilution. In order to achieve gloss and abrasion resistance requirements of the situation according to the paper, roll coated with light plus 5 to about 15% thinner, with inline coating liquid, the use of high viscosity coating process should be adjusted to increase the amount of diluent the appropriate viscosity. 2, Varnish on paper should meet the principle, if excessive dilution will affect gloss, abrasion resistance and leveling; the contrary will result in dilution of inadequate leveling varnish is not good, the drying rate is too slow . 3, depending on fuel quality and gloss paper requirements, are generally on-line coating of :2-5 g / m, offline coating 3-7g / m. 4, drying method: to use infrared drying, hot air or heat pipe heating and drying. Drying equipment operation during the first table shows the temperature not lower than 70 . 5, Take 12 hours after polishing of the varnish in order to achieve optimal performance. 6,It can use water to clean equipment, the dry varnish can used Isopropyl alcohol or alcohol to clean. 7, the product of alkali-soluble varnish, when veneer to the cartons (laminating), try to choose a neutral or weakly alkaline (PH 10) adhesives, when used starch caustic soda glue (yellow glue) fluid, Please be strictly controlled to avoid excess glue with a glue penetrate varnished surface caused by dissolution of the coating adhesive. Package: 25KG/50KG/120KG plastic containers, sealed in a cool place, the shelf life is one year.
This is a special paint with extreme adhesion to glass surfaces. It is sprayed onto any type of glass to produce coloured glass panels.
12cans per carton. High quality. 12cans x 16oz/per ctn.
Scope of application: 1. Electron, appliance, ironware, machine factory 2. Chemical, medicine factory, lab 3. Food, textile, supermarket, parking lot. Features: Dust-proof, waterproof, mold-proof, chemical resistant, wear-resistant, strong adhesion, smooth and seamless, simple construction, easy to clear and maintain. Construction technology: 1. Waterproof treatment: first floor needs well done waterproof; 2. Basic ground treatment: polish, fix and clean according the basic ground condition; 3. Epoxy primer: use strong Permeability and adhesion epoxy primer roll-coating one time, strengthen surface adhesion; 4. Epoxy putty: construction several times according practical demand, up to smooth without holes, mark of Batch cutter and sand polish; 5. Epoxy topcoat: use epoxy topcoat or slip-resistant topcoat roll-painting two times, when finished the floor is smooth and clean, color average and no hollowing. 25kg/drum.
Jelee water based glass baking enamel is made with modified acrylic resin as raw material. 25kgs in plastic drums.
Interior exterior water based paints.
Commercial paint for interior or exterior use. Various shades of Blue, green, red, yellow, tan, off white, gray. 275 gallon totes. 14 totes per truckload, 3850 gallons US.
Paints. Its all paced in 1/4/20/200 ltrs drum packing.
Acrylic paint for indoor and outdoor painting 200 cans
Brief Description: PLATIVE PLP4500 plating layer protective paint, is designed to protective the plating layer by improving abrasion resistance, scratch resistance, chemical corrosion resistance, insolation and heat stability. The paint of transparent has no effect on the color of plating layer, besides the paints of colorful can make the plating layer with different coloration. Operational Guidance: Prefabricated, diluted PLATIVE PLP4500 to a proper consistency and add 15% -25%to total PLATIVE SN30, mix completely. Clean and dry the plating layer, make sure no oil, no dust. To paint the layer with prepared paint by spraying, immersion or drawing. Then forced dry at 120 in 50 minutes, or air dry in more than 12 hours. Annotation: Before use, low-speed mixing of PLATIVE PLP4500 is required; dilute the product with special solution ALATIVE PLP4500, or else it could lead to paint deterioration.
As per paints standard. 1 ltr ~ 4 ltr, normal packing as well as Industrial standard packings.
