Additionally, it delivers strong strength characteristics at elevated temperatures-up to 2200 degrees Fahrenheit. Alloy-X is well suited for forming and welding.
Common applications of type Alloy-X include:
Gas turbine operations
Petro-chemical
Structural components
Industrial furnace
Fahrenheit and for lower stress applications at higher temperatures. A-286 can be hardened to a strength level. The alloy is also useful for low temperature applications requiring a ductile, non-magnetic high strength material at temperatures ranging from above room temperature down to at least -320 degrees Fahrenheit. This alloy can also be used for moderately corrosive applications in aqueous solutions. All of our A-286 is ordered to specific decimal thicknesses.
Supply of several non-ferrous cast alloys in the shape of ingots, The alloys available include:
1)Aluminum alloys
Pure A1 , Al- Si, Al-Mg , . etc.
2)Copper alloys
Pure Cu, Cu-Zn
3)Zn alloys
4)Pure Lead and lead alloys.
Specification of the supplied ingots.
1.Sizes in the range of :
Al65178 Cm
Cu4677 Cm
2.Weights:
Al12 Kg
Cu14 Kg
Zn10 Kg
Pb50 Kg
Moreover, alloys with specific chemical composition could be supplied according to the customer request.
Silicon steel
1.0 scope
1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide
Low core loss and high permeability needed for more efficient and economical electrical
Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used
For transformer cores and large generators.
2.0application
2.1 the cgro is used regularly for cores in transformers.
3.0standard
3.1 this specification is prepared by taking guidance from bs 601:1973
4.0material
4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and
Equivalent to jis c 2553
5.0properties
5.1 specifications and typical electrical and magnetic properties (see appendix 1)
6.0dimension and tolerance
6.1 dimension : as per the purchase order with the tolerance as given table below
Tolerance on width
Nominal width (mm)
Overup to and includingtolerance (mm)
0150+ 0 0.3
150500+ 0 0.5
001000+ 0 1.5
Tolerance on length
Nominal width (mm)
Overup to and includingtolerance (mm)
02000- 0 + 1.5
2000>2000- 0 + 2.0
Tolerance on length
The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be
0.03 mm from the nominal thickness.
Tolerance on edge burr
The tolerance on edge burr not to exceed 0.05mm.
Tolerance on edge camber
Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a:
Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil.
7.0references
(1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus.
3710 Metal Alloys Suppliers
Short on time? Let Metal Alloys sellers contact you.
Packing: 25kg/40kg/50kg , plastic bag inside and carbaord drum outside
Chemical properties: the color is yellow-orange. The relative density is 3.357g/cm3 . It is not soluble in anhydrous ethyl alcohol but can dissolve in acids or alkali. The steam is poisonous and the relative molecular weight is 181.88 .
Quality guarantee :
Advanced technique, completed resource controling system and hard and fast measurement of products , which all make sure of the products stability . Today our products have been sold all over the world like america , german , middle east and so on . We have about twenty years experiences of production and have enjoyed good reputation in this line .Welcome to contact us !
We manufacture ferro alloysall grades of alloy steel, special steel and stainless steel in rounds, flats, squares and profiles in black and bright as per the customer's requirements.
We have started trading of below materials in domestic market.
1: moly oxide / ferro moly
2: nickel
3: low carbon ferro chrome
4: ferro silicon
5: hms
6: shredded scrap
7: ss 304 scrap
8: ss 316 scrap
9: cupro nickel ( 70/30)
10: monel, inwar, inconel, reformer tube ( high nickel/ moly scrap)
All the handle can be fixed in sash door, wooden door, frame door optional and cabinets, the usefulness is very widely.
The surface of all the stainless steelhandle can be high-quality processed for smooth , abrasive, half-abrasive. The products are more and more beautiful.
All handles can be manufactured to meet customer special material requirements, including stainless steel, steel and zine alloy.
Ferro silicon
Chemicall detail as follow
Specs: Si:75%min.or Si:72%min. Al:2.0%max. C:0.2%max. S:0.02%max. P:0.04%max.
Size:10-100mm,10-50mm 90%min.
Packing: in plastic woven bags of 1mt net each or in bulk.
The annual output reaches 10,000mt
