Silicon steel 1.0 scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0application 2.1 the cgro is used regularly for cores in transformers. 3.0standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) Overup to and includingtolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) Overup to and includingtolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0references (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus.
Nickel Nitrate : Grade: Tech Content: 98% Properties: Crystal MOQ: 1FCL Packing: 25kg/bag Attention: Export Tariff: Views : 116 Molecular formula: Ni(NO3)2.6H2O Molecular weight: 290.81 Physicochemical Properties: Nickel nitrate hexahydrate is a green monoclinic system crystal. Specific Density: 2.05, Melting Point: 56.7 C, Boiling Point: 137 C. When heated at 56 C, it decomposes into trihydrate by losing three water molecules and then converts into anhydrous salt at temperature of 95 C. It easily dissolves in water, and is soluble in alcohol, and slightly soluble in acetone. Applications And Usages: It is mainly used to produce other inorganic and organic nickel compound, to manufacture catalysts and carrier materials, or used as corrosion inhibitors, dye mordant, as well as in glass industry and colored glaze for ceramics. Packing: 25kg weaving bag with plastic liner or according to the requirements of customers.
River sands, sea sands, iron ore, lpg, biodiesel, cp10, cp8 palm oil iron ore: 300 thousand mt/ month river sand: 100 thousand mt/ month palm oil 100 thousand mt/ month nickel ore: 100 thousand mt/ month silica sand : 200 thousand mt/ month.
Stainless steel scrap, metal scrap , bitumen, gasoline , nuts.
Core steel plate Specification for core steel plate 1.0Scope 1.1 this specification covers the grain oriented electrical steels are iron-silicon alloys that provide Low core loss and high permeability needed for more efficient and economical electrical Transformers. Cold rolled grain oriented (crgo) grades of electrical steel are typically used For transformer cores and large generators. 2.0Application 2.1 the cgro is used regularly for cores in transformers. 3.0Standard 3.1 this specification is prepared by taking guidance from bs 601:1973 4.0Material 4.1 cold rolled grain oriented (crgo) grade m5, moh, zdkh as per bs 601:1973 and Equivalent to jis c 2553 5.0Properties 5.1 specifications and typical electrical and magnetic properties (see appendix 1) 6.0Dimension and tolerance 6.1 dimension : as per the purchase order with the tolerance as given table below Tolerance on width Nominal width (mm) OverUp to and includingTolerance (mm) 0150+ 0 0.3 150500+ 0 0.5 001000+ 0 1.5 Tolerance on length Nominal width (mm) OverUp to and includingTolerance (mm) 02000- 0 + 1.5 2000>2000- 0 + 2.0 Tolerance on length The tolerance on the mean thickness, measured by contact micrometer, for any coil shall be + 0.03 mm from the nominal thickness. Tolerance on edge burr The tolerance on edge burr not to exceed 0.05mm. Tolerance on edge camber Edge camber is the lateral departure of the edge of the strip from a straight line forming a chord, refer figure a: Tolerance on edge camber of strip in coil shall not exceed 2 m in 2000 mm and shall be measured against a straight edge using a 2000 mm length cut from a coil. 7.0References (1) bs 601: 1973, steel sheet and strip magnetic circuits of electrical apparatus. As provided above
