Squeege: Â 60-65 SHORE
Mesh: 120/inch
Tension: 25 N/cm2
Clean Up: Â Water
Strokes: Â 3
Rounds  2
Printing Application
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 4 hours ambient drying.
3. Heat cure at 130 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 â?? 4 hours ambient drying.
3. Heat cure at 130 â?? 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 4 hours ambient drying.
3. Heat cure at 130 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130 - 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130 - 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
Squeege:70-75 SHORE
Mesh: Â 120 190/inch
Tension:Â 25 - 35 N/cm
Clean Up:Â Water
Strokes:Â 3
Rounds:Â 2
Printing Application
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130 - 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
Squeege:60-65 SHORE
Mesh:Â 120/inch
Tension:� 25 N/cm2
Clean Up:Â Water
Strokes: Â 3
Rounds: Â 2
Printing Application
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 4 hours ambient drying.
3. Heat cure at 130 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 4 hours ambient drying.
3. Heat cure at 130 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 4 hours ambient drying.
3. Heat cure at 130 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 -4 hours ambient drying.
3. Heat cure at 130 - 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 4 hours ambient drying.
3. Heat cure at 130 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130 -160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130 -160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130-160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 â?? 4 hours ambient drying.
3. Heat cure at 130 â?? 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130 -160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 -4 hours ambient drying.
3. Heat cure at 130- 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130- 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130- 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
1. Blow dry print in between rounds using hairdyer or other methods.
2. Allow for 2 - 4 hours ambient drying.
3. Heat cure at 130 - 160oC for 2 minutes.
4. Allow for 24 hours after heat cure before any physical testing of prints.
