Make: JSW
Model: J850EII
New : 1998
Specfication:
Screw Diameter: 100 mm
Injection Pressure: 1,730 kg/cm2
Theoretical Injection Capacity: 3,788 cm3
Injection Weight (PS): 3,429 g
Injection Rate: 840 cm3/sec
Plasticizing Capacity (PS): 470 kg/h
Screw SpeedHigh Torque: 75 rpm
Low Torque: 150 rpm
Nozzle Output: 50 mm
Injection Head: Open Nozzle
Cylinder Temperature Regulator : Cylinder 4, Nozzle 1
Clamping Method: Double Toggle
Clamping Force: 850 ton
Daylight: 2,300 mm
Clamping Stroke: 1,200 mm
Mold Thickness: 550 – 1,100 mm
Distance between Tie Rods (H x V): 1,060 x 1,060 mm
Platen Size (H x V): 1,560 x 1,560 mm
Ejector Method: Hydraulic Cross (29 points)
Ejector Force x Stroke: 23.1 ton x 200 mm
Mold Open/Shut Speed (Shut - Open): 67 m/min - 65 m/min
Pump Motor: 105 kW
Heater: 35.83 kW
Oil Tank Capacity: 1,360 L
Total Electricity: 143 kW
Machine Size (L x W x H): 11.0 x 2.5 x 2.6 m
Machine Weight: 43 ton.
Special drying chicken manure machine produced by our company is highly efficient, energy-saving new products; the project is applicable to large and small farms, aquaculture in more developed regions.
The machinery is divided into large and small.
2. Equipment capabilities
1). width of raw materail : 60mm- 860mm
2). Product speed by punching: 2.5-5m/min
3). Continuous roll forming speed: 10-15m/min
4). Material thickness: 1-2mm
5). Material require: Q235 cold roll steel
6). Production line has automatic and manual two operating mode, may realize the linkage and the partition revolution work.
3. Main composition of machine
This unit consists of the decoiler, ML900 flatting, 200 punch, punching die, servo feeding, guider, main roll forming machine, follow cutting, cut-to-length part, electrical control cabinet; etc.
4. Each part major technical parameters
4.1 Drive decoiler
1). Material width 860mm
2). Material weight 6000kg
3). Material outer diameter 1200mm
4). Drive power: Electromotor and speed reducer integration, 4KW frequency conversion electromotor
5). Frame type: Cantalever inner support, manual handle afterbody, pneumatic press cantalever.
4.2 Flatting
1) Working rolls: 11 rolls, up 4/down 5, the residual 2 rolls is clamp deliver rolls.
2) Flatting bound: Material thickness 1-2mm, material width 100-860mm
3) Drive power: 5.5kw frequency conversion electromotor
4) Speed reducer model: ZQ250
5) Flatting speed: 3-10 m/min
6) Parenthesis up and down a pair of fortified wheel
4.3 Continual punching mould
1. Amount: Each kind of width specification 1 set dies, total 6 sets
2. Die require: Cr12 quench
4.4 Servo feeding
1. electromotor power: 4.4kw
2. Multistage type feeding, memory ten group of memory functions
3. Man-machine contact surface numerical control system
4. Uses Mitsubishi servo meter
4.5 Holds material (use in cushion section)
The roller type, the both sides have the bearing support, 3 sets, use in holding the material and under the deposited material spacing
4.6 Guider
A pair of horizontal roller and two pairs of vertical guide rolls, total 1 sets.
4.7 Main roll forming machine.
Type
GY180(Extra wide)
Rack structure
Dragon Gate type memorial arch frame
4.9 Electrical control
4.9.1 Main operation control cubicle
1) Amount: 1 set
2) Frequency conversion: 3 sets(in main control cubicle, control decoiler, flatting and roll forming machine)
3) PLC control: 1 set
4)8 inch liquid crystal touch screens
5) All electrical element is the Mitsubishi original installation brand
4.9.2 assistant control cubicle
Amount: 3 sets (follow decoiler, flatting, roll forming machine)
Control type : Manual handle
5. After-sale service
1. We see to the equipment's installment, the debugging and free training operators
2. We offer the equipment's details(including the drawing of roll forming mould, Electric appliance schematic diagram, equipment diagram and so on).
1875 Injection Moulding Machinery Suppliers
Short on time? Let Injection Moulding Machinery sellers contact you.
Naroto is rotational moulding machine manufactruing and supplier company based in india, we are also export plastic moulding machines, rock n roll machineservices in India.
Product id: tec series
1. The injection molding robot-mini traversing robots are extensively applied to plastic injection molding machine 50t ~ 150t.
2. The mini traversing robots can rapid take out the runners, sprues and find products from the mold of plastic injection molding machine.
3. The mini traversing robots can achieve factory inline automatically system.
Dialog controller, easy to control
1. The control system meets ce, spi and euromap standards, which is compatible with injection molding machines all over the world.
2. Remote controller with the lcd display for easy reading. The screen capacity is 100 chinese characters.
3. Choice of english / chinese displays on screen.
4. 16 bit dual cpu provides powerful editing functions for deletion, insertion and replacement.
5. The program copy function, in conjunction with the edit and modification function, provides easy program editing and modification.
6. 60 sets standard programs combined with 40 sets edit meets requirements for any type of mold.
7. Machine interface contains: mold clamp interlock, injection interlock, mold eject interlock, safety door control, product counting and cycle time.
8. Specially designed outside mold hold function suits extra high molds and molds with core cylinders. This prevents molds bumping against the robot.
9. Middle platen confirmation device (optional): a safety guard to prevent the middle platen bumping against the robot resulting from incorrect positioning of middle platen.
Screw barrel:38crrm nitriding
Gear-box:hard-toothed cover
Vacuum venting device:vacuum degree:0.08mpa
Forecd feeding system motor power:1.1kw
Electric machine: low pressure electric machine:simenz;
Temperature control: omron, intelligence module control
Scerw diameter:80/156 alloy
Screw rotary speed:1-36.9rpm.
Main moter power:55kw, frequency control
Frequency adjuster: fuji
Barrel heating power: 36kw cast aluminum heating ring;
Stainless steel out shell, air-cool constant temperature
11.Capacity:>400kg/h
The process is used to recycle big capacity and stable quality raw material, especially for psf manufacturer and recycled poy manufacturer with big capacity. The process flowchart as below:
De-baling----- label scrapping------ label separation------- bottle pre-washing--------manual sorting and metal detecting-----wet grinding-------gravity separation-------chemical washing for pet flakes-------rinsing--------drying--------packing.
Specification:
Power : ~380 kw
Capacity : 3 mt/hour input
Area requirement: 1000m2.
Flakes quality criteria:
Size: 1 mm ~ 12 mm
Humidity: 1.5 %
Pe, pp: 20 ppm
Paper, wood: 20 ppm
Glues/hot melts: 20 ppm
Organics: 20 ppm
Inorganic particles: 20 ppm
Ferrous and non-ferrous metals: 20 ppm
Pvc: 30 ppm. Our pre-washing process can make pvc become distinguishable. But the efficiency of labors in bottle sorting unit is important.
Colored pet flake: should be less than 20 ppm. But it should depend on efficiency of bottle sorting labors.
1 it can smash any plastic material rapidly and can be applied on several usages. Ití»s a smasher with full power.
2 the big plastic materials can be smashed directly without blocking which will result in the stopping of smash. So it can save a lot of time.
3 with water cooling system and the clearance between cutters provide facilities of heat dissipation in order to reduce damage effect between bearings and machine bodies and lessen the depreciation of steel characteristics.
Specification:
Power : 75kw
Capacity :maximum 1600kgs/hour at 12mm hole in the screen
Dimension: l1800 x w1500x h2400 mm.
Item nsk-285 unit
Screw rod diameter ø70 mm
Ejective capacity 600 cm³/shot
Screw revolution 0-100 r.P.M.
Motor of spiral oil pressure 275 kg-m
Motor of oil-pressure pump 6p x25hp kw/pole
Mould clamping force 50 ton
Mould clamping space(max.) 185 mm
Size of mould available (max.) 180 x 400 mm
Mould clamping frame 20 station
Electric heating capacity(glue) 8 kw
Acting oil capacity 550 l
Machine size 3700 x 2500 x 1750 mm
Machine weight 5.9 ton
Gross weight 6.4 ton
Packing dimension 4000 x 2040 2150 mm
1.Nsk-213(4stations or 6 stations) for single manual operation have high mobility and efficient
Suited for few order, sample, testing mould.
2.The unique design of producing have good cooling system to use materials of foaming and no
Foaming , when using foaming material let production not change color, not change quality expand
The best foaming effect.
3.It is suitable for p.V.C. Foaming, t.P.R., solid p.U. & n.B.R.
4.Photoelectric digit control system with 3 patents divides quantity of materials into four steps to
Control ejection quantity respectively and precisely.
5.The disc is computer operated to protect the system well especially to the moulds.
6.Movement of disc is hydraulic control with hydraulic brakes , enabling a stability in the movement
And accuracy in positioning.
7.Special hydraulic design with speedy , low electric cost drive by 20hp motor.
8.Hydraulic closed mould system with powerful mould locking and would not create fiber trims and
Peermeation of colors.
9.Efficient cooling system have good effect of cooling and stable quantity.
10.Cooperate with auto turn last system, auto clamping system easy to operation and high
Capacity.
The molds of the former vertical injection molding machine for rain boots was liable to wear down.The quality of rain boots was not good,and the machine was not easy to operate.Therefore,we imported the latest technique to develop the "Auto rotary injection molding machine for rain boots".The molds of NSK-375 can open and close automatically,which can save manpower and make it easy to operate the machine.With the "Wind pressure auto molding system",the operators can easily remove finished products from the molds without damaging the lasts so that the molds can last longer.
The NSK-375 adopts direct-pressure injection which generates high pressure.It can produce boots of different sizes at the same time.The high clamping pressure ensures the quality of products.The machine can produce boots of different sizes or heights simultaneously,which reduces production time.Furthermore,the machine also can produce sandals by changing the molds.
Product Character
1.The NSK-375 is the first machine with the photo-cell digital locating system in Taiwan. It is easy to accurately adjust the ejection quantity.
2.The machine is specially designed for producing rain boots. It is automatic, economical,efficient, and easy to operate.
3.The machine is run by a hydraulic system. The machine can adjust clamping pressure and can work at high speed.
4.The NSK-375 has eight(8)molds; freely select their usage; molds can be opened and closed manually or automatically.
5.Besides the 16"(45mm) rain boots, it can also produce pumps, slippers, and sandals.
6.With the "Wind pressure auto mold-opening device", the operators can remove the finished products from the molds without damaging the lasts. The molds can therefore last longer.
7.Two options for ejection quantity are available: a fixed quantity or full mold.
8.Powerful mold clamping prevents burrs.
9.Many different sizes of rain boots can be produced at the same time. Also sandals and rain boots can be produced simultaneously.
10.The machine is suitable for P.V.C.,T.P.R.,and N.B.R...etc.
Sandwich panel forming line is specialized machine of new type building material, it main function is compounding color steel on thick, lighter core material eps panel or rock wool panel.
Sandwich panel is one new type building material, ideal decorate material, lightweigt, high intensity, good appearance, convenience construct, short period of construction, and have heat preservation, waterproof and so on kinds of nature.Suitable for bulk storage plant, industral factory building, large-span roofing, frige, clean room, air conditioning equipment room and temporary shelters.Our sandwich panel forming line can produce six different panel.
Max width: 1200mm
Max thickness: 25cm
Working speed: 0¡«3.8M/min
Power: 34.1kw
Weight: 15¡«16t.
Suitable for all kinds of fabric
Variable speed from 0-60mtrs/min.
Counter meter for length measurement
Selvedge guider for uniform plaiting.
Tensionless handling of fabric through positive drive.
Independent variable feed drive for tensionless feed also fitted with auto loop level positioning mechanism
Maximum working width up to 300 cms
Pile height 35 cms
Adjustable fold length 75 – 110 cms
Adjustable table lowering through special electro-mechanical controls depending upon the fabric thickness
1875 Injection Moulding Machinery Suppliers
Short on time? Let Injection Moulding Machinery sellers contact you.
