Lubricants , metal working additives, metal working chemicals cutting coolant, semi synthetic cutting coolant, corrosion inhibitor for metal working , etc..
Fuel oil treatment general cleaners oil spill dispersant multipurpose cleaner oil industrial cleaner carbon remover electric cleaners motor cleaner oil filter cleaner scale remover scot remover rust remover rust preventive paint remover air conditioner cleaner hand cleaner eliminate odor cutting oil water treatment cooling water treatment boiler water treatment cooling water treatment test kit boiler water treatment test kit oil treatment corrosion inhibitor for gas scale inhibitor oxygen skavenger microbiocide demulsifier pour point depresant paraffin control fire extinguisher liquid foam 3% afff.
Lc 141 is single product treatment designed to prevent Scale deposits and corrosion to ferrous and non-ferrous Surfaces in hot water heating systems and chilled closed Loops. It passivates the surfaces and forms a barrier layer to Inhibit corrosion. It is a synergistic combination of Phosphonates, polymers and phosphate. Application Easily feed/injected directly into the system by means of a chemical by Pass feeder. Dosage Initial treatment is 1 gallon per 1, 000 gallons of water in the system. There After add lc 141 to maintain a level of 25-35 ppm (mg/l) of Orthophosphate. Handling & precaution It is highly alkaline and should be handled with care to prevent personal Injury. Protective clothing and eye protection should be provided and worn. In case of skin contact , immediately flush thoroughly with plenty of clean Water. In case of eye contact, flush with copious amounts of water for 15 Minutes and obtain immediate medical attention. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 144 is formulated to prevent and reduce scale, Rust, corrosion and sludge in generator system. It is The most effective coolant for generator and other High temperature systems. Lc 144 is a special blend Of selective glycols, anti-corrosion additives and Sludge conditioners that provide smooth running of The systems. Application Lc 144 is widely used in power plants, generator system, etc... Found in Marines, aviations, industries, automotives, industries, hospitals, etc. Benefits ? excellent protection ? no more severe Damages ? non-flammable ? non-polluting ? non-corrosive ? non-toxic ? completely safe to Use ? reduces costly Maintenance Dosages 1. Check incoming water source for total hardness and chloride. 2. Recommended total hardness below 30 ppm and chloride below 50 Ppm. 3. Lc 144 can be diluted at a ratio of 1:1, 1:5, 1;10, 1:32 with deionised Water (recommended). 4. Repeat application monthly or quarterly depending on application. Flush if colour changes or becomes cloudy. Handling & precaution For professional use only. To be used in well ventilated environment. In Case of contact with eyes, rinse thoroughly with water and seek medical Advice immediately. If swallowed, take plenty of water and seek medical Advice immediately. Avoid prolonged contact with skin. Put on gloves for Sensitive skin. Keep out of reach of children. Additional information may Be obtained from material safety data sheet (msds). Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 238 is designed specially for use in systems where the use Of concentrated acidic or concentrated alkaline descalers are Not recommended. This product is specially formulated for Specific cleaning and descaling purposes for sensitive system. Lc 238 may be re-circulated by means of a high volume pump For the removal of scale. Lc 238 can be used safely on to Copper & brass surfaces besides being very effective in steel System. This product contains organic poly acrylic & polymer Compound. Application Lc 238 may be soaked overnight and re-circulated. When scale is Present, the tubes should first scraped out to remove as much as possible And then flushed out with a hose. Dosage Circulate an appropriate concentrated solution based on the scale and Corrosion. For storing / stand by system use lc 253 or lc 252. For more Detail and specific method and concentration, please consult lifechem Technical services. Handling & precaution This product ph is between 4.0 – 9.0 and should be handled with care to Prevent personal injury. Protective clothing, gloves and eye protection Should be worn. In case of skin contact, immediately flush thoroughly with Plenty of clean water. In case of eye contact, flush with copious amounts Of water for 15 minutes and consult a physician. Refer to material safety Data sheet for more specific procedures and directions. Packaging Available in pail of 20 lt.. Can also be custom packaged .
Lc 126 condenser water treatment does not use sodium Chromate, zinc or other toxic chemicals in its composition. It Eliminates the serious pollution problems usually associated With the use of such chemicals for corrosion and scale Control in cooling system. It protects medium size cooling Towers against scale, sludge and corrosion. Lc 126 Contains a special anti-foulant additive to reduce Accumulations of mud and silt in condenser tubes. Ideal for Average towers with 75 to 500 ton capacity. Application Formulated for use in open re-circulating cooling water systems found in air Conditioning and process operations. Apply manually, directly to the cooling Tower basin. Dosage Initial dosage : add 1 gallon of lc 126 for every 500 gallons of system Capacity. Maintenance dosage : add 1 gallon of lc 126 for every 1, 000 gallons of System water lost to bleed off from the cooling tower system Handling & precaution Slightly alkaline aqueous solution. Keep out of reach of children. Refer to Material safety data sheet for more specific procedures and directions. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 233 is a special blend of non-volatile acids, corrosion inhibitors, emulsifiers & dispersing agents. Effectively removes rust, scale and soil from metal and concrete surfaces. Application May be sprayed or brushed on surfaces. Clean surface free from rust, soil and dirt. Apply LC 233. Allow to stand for 10 - 20 minutes, then wipe off with water. Dry surface can be repainted if desired for longer protection Dosage For descaling of condensers, dilute one part of LC 233 with upto 10 parts of water depending on the thickness of scales. Allow to stand for several hours. Flush with water until all scale are removed from condensers. Handling & Precaution Irritating to eyes and skin. After contact with skin wash immediately with plenty of water. In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek medical advice. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Swift MFL portable instrument with a large, premium-quality multi-touch display. Incl.2 batt., power supp., manual, rugged case. Highlights : Fast, reliable corrosion screening even in service Portable, battery-operated, sealed, large bright display Simple to learn and operate, offers a high PoD SPECS : Acquisition modes Internal Clk, Encoder Array connectors 1x IPEX Batteries - typical life 6-8 hours Cooling Sealed with internal fan Data storage SSD, 100 GB Display resolution 1024 768 Display size 26.4 cm (10.4) Display type Capacitive multi-touch, with 3 mm (1/8 in), chemically strengthened glass cover. Non-reflective (AR coating), anti-fingerprint (oleophobic coating), optically bonded LCD and touchscreen. Passive backlight enhancement Full recordable data for mapping Yes High temperature inspections Yes Highly portable easy to use system Yes Multitouch control Yes Nb. of input channels 8 Nb. of receiving elements Up to 128 Paperless Reporting Yes Precision active steering No Probability of detection 2mm diameter 20% loss Probe type MFL Rapid Coverage Yes Rope access applications Yes Setup creation/management Yes Umbilical length 5m, 10m and 15m Acquisition rate Up to 50 kHz Automatic screenshot with defect entry Yes Batteries - type 2x li-ion, rechargeable, DOT compliant Compliance EN 61010-1, CE, WEEE, FCC, Part 15B, ICES-003, RoHS Defect table (for reporting) Yes Digitizing 16-bit resolution Encoders and I/O connectors 1x 12-pin Fischer Inspection workflows Optimized, with hard buttons MFL receiver gain 23 - 64 dB Programmable alarms Yes Recordable UT data sets Yes RFT/NFT/MFL connector Yes Harness available Yes Full screen mode Yes Connectivity Gigabit Ethernet, Wi-Fi, HDMI, USB 2.0 (x3) Dimensions (W x D x H) 355 288 127 mm (14.0 11.3 5.0 in) Encoder inputs 3-axis Quadrature / Step /Dir, TTL 5V IP rating IP65 Operating humidity 95%, non-condensing Operating temperature 0 C to 40 C (32 F to 104 F) Power supply/requirements Battery Operated Programmable outputs Yes Supported Technologies/Techniques MFL Storage temperature 0 C to 40 C (32 F to 104 F) Volume 13L (793.31 in3) Weight (without batteries) 5.7 kg (12.5 lb) Video output HDMI Weight (with batteries) 6.6 kg (14.5 lb)
Application LC 231 is a special blend of volatile acids, corrosion inhibitors & dispersing agents. It effectively removes scale and soil of carbonate nature from metal and other surfaces. LC 231 is an excellent additive for the LC 233 for the initial removal of the carbonate based scale and effectively bring down cost by reducing the amount of other descalers. Its acid formulation dissolves lime scale and rust deep down with the selective inhibitors protecting metal surfaces. Application Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC 231. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat and then flush off with water. Flush with water until all scale is removed. Add with other descaler like LC 232 & LC 233 for stubborn and difficult to remove scales. Cannot be used alone. Dosage Dilute one part of LC 231 with up to 10 parts of water depending on the thickness of scales. Handling & Precaution Irritating to eyes and skin. Protective clothing and eye protection should be provided and worn. After contact with skin, wash immediately with plenty of water. In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek medical advice. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 253 is an alkaline concentrated food grade product Designed for “passivating“ as well as neutralizing the Metal surfaces that is succeptable to corrosion. Lc 253 Is also an alkaline formulation of phosphate, polymeric Dispersants and corrosion inhibitors. It is designed to Control corrosion and neutralize any acidic left over from Acid cleaning processes. It contains no chromate or Heavy metals. Application Can be added directly into the raw water to give a 2% to 10% solution, Which then may be used for “passivating”, “neutralization” & “protection”. For offline storing purposes a 0.5% solution may be quite effective. The Surface to be passivated, neutralized or get protection must receive a Minimum of 15-30 minute contact time. Dosage Dosage is calculated depending on the circulating or storing volume and The time of contact. A diluted solution of 0.5% up to 10% is recommended. Use concentrated solution for less contact time & higher initial conditions, Where as a 0.5% solution may be used for storing. Handling & precaution This product is quite alkaline and should be handled with care to prevent Personal injury. Protective clothing and eye protection should be provided And worn. In case of skin contact, immediately flush thoroughly with plenty Of clean water. In case of eye contact, flush with copious of amounts of Water for 15 minutes and obtain immediate medical attention. Packaging Available in pail of 20 lt.. Can also be custom packaged
LC 101 is used in steam boiler systems where water is zeolite softened or in natural waters very low in hardness. This treatment will prevent scale formation from residual hardness in addition to conditioning sludge. LC 101 is a balanced blend of polymers which are mildly alkaline scale and corrosion inhibitors in addition to sodium sulfite for added pitting and corrosion protection. If 20 to 30 ppm (mg/l) of sulfite cannot be maintained with a normal dosage of LC 101, add LC 102 to hold this recommended level. Application: Easily fed to the boiler as a slug dosage or by chemical proportioning pump directly in to the boiler. It can also be injected into the feedwater tank. Formula LC 101 contains no heavy metals. Dosage: Initial dosage is one (1) quart per 1,000 gallons and one (1) quart thereafter for every 800 gallons of make-up water. Maintain 20-30 ppm (mg/l) of orthophosphate in the boiler water. Handling & Precaution: Wear protective clothing and eye protection should be provided and worn. In case of skin contact, immediately flush thoroughly with plenty of clean water. In case of eye contact, flush with copious of amounts of water for 15 minutes and obtain immediate medical attention. Packaging: Available in pail of 20 lt.. Can also be custom packaged.
Kb 236 is a special blend of mineral acids, Corrosion inhibitors, emulsifiers & dispersing Agents. Effectively removes rust, scale and soil From metal and other hard surfaces. Application May be sprayed or brushed on surfaces. Clean surface free from Rust, soil and dirt. Apply kb 236. Allow to stand for 5 - 15 minutes, Then wipe off or flush with water. Dry surface can be repainted if Desired for longer protection. Dosage For cleaning surfaces, dilute one part of kb 236 with up to 10 Parts of water depending on the thickness of scales, soil & dirt. Allow to stand. Brushing may be required. Flush with water until all Scale are removed Handling & precaution Acidic product. Irritating to eyes and skin. After contact with skin Wash immediately with plenty of water. In case of eye contact Irrigate thoroughly with water for at least 15 minutes. Seek medical Advice Packaging Available in pail of 20 lt.. Can also be custom packaged.
Non-Invasive & Non-Destructive Wireless Technology¯ Unlike other devices which must drill into the concrete and physically connect to the rebar to evaluate corrosion, the is completely non-destructive. Fast & Accurate Real Time Data in Seconds Data is collected, analyzed, and stored wirelessly within the mobile app on the tablet provided where it can be easily shared with team members. Automatic Report Generation Simple Detailed corrosion evaluation of reinforced concrete structures is presented as contour maps which are accessible in real-time on the tablet. Recipient of NACE Corrosion Innovation Award iCOR is the most advanced wireless corrosion measurement device for evaluating the health of reinforced concrete structures. iCOR detects corrosion potential, corrosion rate, and in-situ electrical resistivity. In 2019, the iCOR was presented the Corrosion Innovation Award by the National Association of Corrosion Engineers (NACE). Applications Detection of corrosion in reinforcement Measurement of rebar corrosion rate Evaluation of corrosion potential of rebar Measurement of in-situ electrical resistivity Assessment of concrete durability Rehabilitation and repair of concrete structures Software Real-time contour mapping of corrosion rate, electrical resistivity, and corrosion potential Accurate non-subjective algorithm-based interpretations Multiple and directional parameters tested in a single measurement Easy reporting and data exporting Hardware Non-destructive, and non-invasive wireless technology Measurements obtained and evaluated within seconds Simple and easy-to-use with minimal training required Single-person operation device Tablet included with free Android app Award-winning patented technology Patented Technology iCOR benefits from the patented CEPRA technology that makes it possible to estimate the rate of rebar corrosion through a noninvasive, non-destructive approach. This means that the need to connect the device to the rebar to obtain measurements, which is the case for other commercial devices, is eliminated with the iCOR. TECHNICAL SPECIFICATIONS : Testing Time 3 to 30 seconds Corrosion Rate Range 0 to 500 m / year Corrosion Potential Range -800 to 200 mV / CSE Electrical Resistivity Range 0 to 10,000 m INCLUDED : Beta unit, Tablet with hands-free carrying support, Data Analysis App., User manual, Connection sponges, USB cable, Conductive solution, Carrying Case.
LC 230 is a strong descaler with a special blend of acids, corrosion inhibitors, emulsifiers & dispersing agents. It effectively removes rust, oxides of metals, scale and soil from metal and concrete surfaces. It’s dissolving action on rust, silica and scale is quick and thorough. Its acid formulation dissolves lime, scale and rust right down to the base metal or concrete with the selective inhibitor protecting metal surfaces. Not for materials like glazed tiles and glass. Application Brush or spray on surfaces. Clean surface free from excess rust, soil and dirt. Apply LC 230. Allow to stand for 10-20 minutes, then wipe off with water. Surface may require repainting if necessary. Dosage For descaling purposes, dilute one part LC 230 with up to 20-100 parts of water depending on the thickness scales. Allow standing for several hours and/or re-circulate using pumps. Flush with water until all the scale is removed. Repeat if scale is still present; check pH and maintain below 1.5 during circulation for control. Use LifeChem LC 240 for neutralizing the spent solution before disposal. Contact Field Chemist for further information. Handling & Precaution Irritating to eyes and skin. If contact with skin occurs, wash immediately with plenty of water. In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek medical advice. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 232 is a very strong concentrated descaler, specifically designed to remove silica based scales and other stubborn scales. It is a special blend of volatile acids, corrosion inhibitors & dispersing agents. It effectively removes stubborn silica scale and soil of silicate/phosphate nature from metal and other surfaces. LC 232 is an excellent additive for the LC 231 & LC 233 for additional effectiveness against silica based scales and effectively bring down cost by reducing the amount of other descalers. Its special formulation dissolves scale and rust deep down with the selective inhibitors protecting metal surfaces. Application Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC 232. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat and then flush off with water. Flush with water until all scale is removed. Add with other descaler like LC 231 & LC 233 for stubborn and difficult to remove scales. For best results use circulation or dipping method use of passivating agent like LC 252 or LC 253 is essential. Make test strip before use. NOT TO BE USED ON GLASS/SILICATE BASED SURFACES. Dosage Dilute one part of LC 232 with up to 10 parts of water or depending on the thickness of scales. Handling & Precaution Irritating to eyes and skin. Protective clothing and eye protection should be provided and worn. After contact with skin, wash immediately with plenty of water. In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek medical advice. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 240 is a highly alkaline concentrated product designed For neutralizing the metal surfaces that is susceptible to Corrosion. Lc 240 consists of a blend of soluble carbonate, Hydroxide and corrosion inhibitors. It is designed to control Corrosion and neutralize any acid left from “acid cleaning” Processes. It contains no chromate or heavy metals. It is Food grade, user & machine friendly and environmentally Safe. Neutralized mixtures can safely be disposed into Sewers. [ p – powder / l – liquid ] Application Can be added directly into the liquid volume to give a 1% to 5% solution or add till Ph value is between 6 - 8, which then may be used for neutralization & protection. For offline storing purposes a 0.5% solution may be quite effective. The surface to Be neutralized or get protection must receive a minimum of 5-10 minute contact Time. Dosage Dosage is calculated depending on the circulating or storing volume and the time Of contact. A diluted solution of 0.5% up to 5% is recommended. Use concentrated Solution for less contact time & higher initial conditions, where as a 0.5% solution May be used for storing. Ensure ph value between 6 – 8 before disposal. Handling & precaution This product is quite alkaline and should be handled with care to prevent personal Injury. Protective clothing and eye protection should be provided and worn. In case Of skin contact, immediately flush thoroughly with plenty of clean water. In case of Eye contact, flush with copious of amounts of water for 15 minutes and obtain Immediate medical attention. Packaging Available in pail of 20 lt. Can also be custom packaged.
We are the biggest supplier of Copper/ Brass / Alloy manufacture in Mainland China. Any of require product could be ask for shipping. Copper has several properties that make it ideal for construction and manufacturing, such as: Copper demonstrates excellent thermal and electrical conductivity, making it suitable for use in electronic and electrical systems and thermal equipment. It exhibits resistance to many forms of damage, including impact, wear, and corrosion. Additionally, it maintains its strength when flexed, formed, and drawn. Bacterial antimicrobial resistance.The material resists bacteria without degrading. It even kills bacteria that are exposed to its surface. This quality makes it ideal for use in food-safe equipment. - Alloy 101/110/122/145 etc. Payment available bank transfer / Letter of Credit.
Product details Standard:Aisi, astm, bs, din, gb, jis Place of origin:Indonesia Brand name:Tis-strut Model number:Tis-strut-001 Material:Highly corrosion resistant hot-dip coated steel Application:Steel structure hanging&support Loading test:Nema standard Standard packaging or according to customer's requirement
FEM Electromagnetic Flow Meters are kind of meters to measure conductive liquid, corrosive liquid with strong acid or alkali. Our FEM Series provide a wide of size range and material measurement with sensor and converter. Applications include agricultural, food & beverage, chemical, pump & paper and water & waste water. General Spec: Accuracy : ± 0.5% Repeatability : ± 0.2% Humidity : 5 to 95% Material – Electrode : 316 Stainless Steel, Titanium, Tantalum, Hastelloy alloy, Platinum Liner : Rubber, PTFE Housing : Carbon Steel, 316 Stainless Steel Temperature – PTFE : 150oC (Option-180oC) - Rubber : 80oC Pressure : 10Mpa (Option-1.6, 2.5, 4.0Mpa) Analog Output : 4-20mA, 500 ohms Max. Load Output Frequency : Scaled Pulse Output (Open Collector), Max. KHz Power Supply : AC220V or DC24V Communications : RS232, RS485, MODBUS, HART Explosion : Explosion ExdIIBT4-T6 Protection : IP65 (Option: IP68) Connection : Flange (DIN, JIS/KS, ANSI).
- It prevents jams in the mechanism of guns - It prevents corrosion/oxidation - It prevents worn out of metal to reach the maximum life time especially for the mechanism and barrel - It is able to protect against corrosion in dampness - It is able to protect corrosion in towards sea water - Compatible for use in various climate conditions. Pour point
