Diameter Spacer tubes Outside 0.197 in (5 mm) 0.197 in (5 mm) 0.236 in (6 mm) 0.236 in (6 mm) 0.315 in (8 mm) 0.394 in (10 mm) Inside 0.098 in (2.5 mm) 0.118 in (3 mm) 0.138 in (3.5 mm) 0.157 in (4 mm) 0.197 in (5 mm) 0.236 in (6 mm) (See SN 60310 as well)
Low alloy grades can resist corrosion in normal conditions. Higher alloys resist corrosion by most acids, alkaline solutions and chloride environments. The corrosion resistance of stainless steel is due to their chromium content. In general, stainless steel contain a minimum of around 10.5% chromium.
Band: 14 Gauge (0.074?[1.88mm]) 304 stainless steel. (S8 and S12) 12 Gauge (0.105 [2.66mm]) 304 stainless steel. (S12 = 40?#216; and up) Engineer/Contractor must specify. 16 Gauge (0.061 [1.56mm]) 304 stainless steel. (Model SL8)
Wire Thickness( 2 Strand wires) : 2.5mm(12SWG) Barb Spacing : 3 to 5inches Length Per KG : 6 Meter /20 Feet Approx Bundle Weight : 25 to 30 KG Length per bundle : Approx 168 Mtr / 550 Feet
Diameter 0.30 mm to 16.00 mm Material High Carbon Steel Size 0.30 mm to 16.00 mm Surface Finish BLACK & GALVANIZED Coil Weight 10 to 1000 kg
Hot Rolled Coils, Sheets & Plates Thickness 1.2 - 25.4mm Width 900-2100 mm Grades Re-rolling/ Drawing Grades, Tube and Pipe/ Forming Grades, Structural/ Medium Tensile Tube/ Forming Grades, LPG/ Low Pressure Vessel Grades, HSLA Grades, Medium Carbon Grades, Weather Resistance Grades, Line Pipe Grades, Chequered Plates
Metal strip is narrow, thin stock that is usually 3/16 in. (4.76 mm) or less in thickness and under 24 in. (609.6 mm) in width. Metal strips are formed to precise thicknesses and/or width requirements.
2. Perimeter channel 0.55 x 20 x 30 x 27 x 3660 mm 3. Intermediate channel 0.9 x 45 x 15 x 15 x 3660 mm 4. Ceiling Section 0.55 x 50.5 x 26 x 26 x 10.5 x 10.5 x 3660 mm 5. Ceiling Angle 25 x 10 x 0.55 mm [Based on 0.9 m suspension]
Diameter 0.30 mm to 16.00 mm Material High Carbon Steel Size 0.30 mm to 16.00 mm Surface Finish BLACK & GALVANIZED Coil Weight 10 to 1000 kg
Standard: ASTM, BS, DIN, GB. Wire Diameter: 4.00mm-12.00mm. ... Prestressed PC Steel Wire. Nominal Diameter, mm(in) Tensile Strength, min, Mpa (psi) Type BA Type WA 6.35(0.250) 1655(240 000) 1655(240 000) 7.01(0.276) 1620(235 000) 1620(235 000)
Dimensions of 316 Stainless Steel Equal Angle Sizes (all Dimensions in milimeter) Approx Weight SS Angle Bar (kilogram/meter) SS 304 Angle Bar Sizes (all Dimensions in milimeter) 40 x 40 x 5 2.97 80 x 80 x 6 50 x 50 x 4 3.05 80 x 80 x 8 50 x 50 x 5 3.78 80 x 80 x 10 63 x 63 x 4 3.90 100 x 100 x 8
Metal Sheet Specifications Overall Thickness: At least. Gauge Thickness: At least. No more than. ... Overall Width / OD: At least. Overall Length: At least. Tensile Strength (UTS, Break): At least. No more than. ... Yield Strength (YS): At least. No more than. ... Elongation: At least. No more than. ... Tensile Modulus (E): At least. No more than.
Diameter 0.30 mm to 16.00 mm Material High Carbon Steel Size 0.30 mm to 16.00 mm Surface Finish BLACK & GALVANIZED Coil Weight 10 to 1000 kg
Finished: Hot dip Galvanized. Tension strength: 700-800 N/mm2. Wire diameter: 2.10 mm. Tolerance: + 0.025 mm / - 0.025 mm. Thickness of Zinc coating: 15-17 g/m2. Coil dimensions: inner diam. about 400 mm. Outer diam: 900 mm. Height: 750 mm.
Designation Thickness (mm) Chemical Composition(wt.%) C Si Mn P S Sol-Al POSHRD2 1.8~7.0 ~0.03 ~0.03 ~0.25 ~0.02 ~0.02 ~0.06 - POSHRD2 2.0~7.0 ~0.005 ~0.03 ~0.20 ~0.02 ~0.02 ~0.06 Ti 0.005~0.05 Nb 0.005~0.04 POSHRD3 2.0~7.0 ~0.005 ~0.03 ~0.20 ~0.02 ~0.02 ~0.06 Ti 0.01~0.06
Steel wool grades and fiber thickness Steel wool is made by shaving thin layers of steel from wires. Steel wool consists of long and relatively strong shavings with sharp edges.
Super Duplex S32750/S32760 Round Bar Specifications Specifications : ASTM A276, ASME SA276 Diameter : 6mm to 350mm Diameter Thickness : 100 to 6000 mm Length Tolerance : +/-0.2mm
2 Tensile properties of the wire shall be as follows: Tensile strength of galvanised M.S. Wire shall be 300 â?? 550 N/mm2. 4.1. 3 Type of coating of galvanise shall be heavy as per IS: 4826 â?? 1979 and the wires shall be galvanised after drawing & annealing.
High Tensile Wire Standard: Both GB/T 20118-2006, DIN, EIPS are available. Nominal tensile strength (Mpa): 1570, 1770, 1870, 1960 etc. Quality control: ISO 9001 etc. High Tensile Wire Diameter: 4 / 4.5 / 4.8 / 5 / 6 / 6.25 / 7 / 8 / 9 / 10 / 12mm. Tolerance: +/-0.05mm. Elongation: 3.5.
Glass Stainless Steel
