Self-Locking Nut with their internal thread form the counterpart of a screw and ensure that the attached screw does not come loose. Lock nuts are resistant to vibration & torque. Nuts are designed to wear faster than bolts. For self-locking nuts, it is acceptable to reuse them as long as there is still some locking action. The number of components is also reduced by the self-locking feature of the nut since no further securing elements are needed. Lock nuts feature a unique design that prevents them from loosening when exposed to vibrations. Because the nut insert hole is smaller than the bolt it creates so much friction between all of the threads that are in contact that the nut cannot vibrate loose.
Slotted/Castle nuts are pre-drilled, they can be used without a pilot hole. These nuts are slotted, allowing them to be installed and removed using screw drivers. It is used primarily as safety nuts, these nuts are slotted to receive a cotter pin or wire which passes through a drilled hole in the bolt and locks it. When a castle nut is applied to a threaded section, it is tightened so that its slot is aligned with a predrilled hole in the bolt or threaded rod, into which a cotter pin, split pin, a lock wire or a spring pin is typically inserted to stop the nut from rotating. Sometimes they are used on trailers too. They are also used as hub nuts that hold the driveshaft within the wheel hub assembly. At HELLARY it is available in stainless steel, carbon steel, and alloy steel to bear more wear and tear while also making it more corrosion resistant.
Spring nuts are one-piece, self-locking nuts that secure screws and prevent them from loosening due to vibration. Long spring channel nuts are used to secure screws in framing channels, cable management conduits, and ducting systems. They consist of a nut with grooves on the side that fit over the side of the channel edge and a screw hole. Tightening a screw in the nut causes teeth in the grooves to lock into the channel edge, holding the nut in place. spring channel nuts are used to place and secure fittings, electrical panels, junction boxes, or piping clamps within channels or conduits.
Square weld nuts have four small projections in their back ends to facilitate their welding onto the surface of other metals. The most significant advantage of using these nuts is that they can be welded into even imperfect and irregular surfaces without losing their balance. The vast majority of weld nuts are manufactured in low carbon steel or stainless steel. They come with a pilot hole using which fasteners can be inserted. The pilot hole is used for precision feeding of fasteners, allowing them to be inserted quickly and accurately on the metal. These nuts are used in automobile and other industrial applications. Aftermarket products such as zinc plating are sometimes used to coat low carbon weld nuts giving it the rust-resistant properties of stainless steel at a substantial cost saving. In addition to possessing very high shear strength, they can also be used in applications that need to resist extremely high torque. At HELLARY it is available in stainless steel, carbon steel, and alloy steel.
A T-nuts are also known as a blind nut, which can however also refer to a rivet nut or an insert nut, and it is a type of nut used to fasten a wood, particle, or composite materials workpiece, leaving a flush surface. It has a long, thin body and a flange at one end, resembling a T in profile. The flanges of T-nuts often have hooks or serrations on the prongs that dig into a wooden workpiece as the bolt is tightened from the opposite side of the piece, providing better retention.
A taper nut is a type of locknut that has an undersized root diameter. This creates interference between the nut and the fastener, plastically deforming the threads on the fastener. Due to this deformation, they are usually only used on permanent or semi-permanent installations. A variation of this nut is the tapered nut. It utilizes a tapered thread to achieve interference. At HELLARY it is available in different materials like stainless steel, alloy, nickel, and many more.
A wing nut or a butterfly nut consists of two large metal wings, one on each side. These wings are applied for easy tightening and loosening using hands, without using tools. The benefit of wing nut is its more ergonomic design that has two tabs that look like wings. It makes it easier to install and remove. Wingnuts are also available in several types as classified by the American Society for Mechanical Engineers (ASME). Type A wing nuts, for instance, are cold-forged. Type B wing nuts, on the other hand, are hot-forged. There are also Type C wing nuts that are die-casted, as well as Type D wing nuts that are made via metal stamping.
A T-Nut, T Nut, or Tee Nut (also known as a blind nut, which can however also refer to a rivet nut or an insert nut) is a type of nut used to fasten a wood, particle or composite materials workpiece, leaving a flush surface. NuWay Industries Pvt. Ltd. is the leading T-Nut manufacturer in Pune, Maharashta, India.
Hex Nuts
Wing nut
Brass Nut
we are manufacturer of HEX NUT in hot forge size M6-M100 and more as per client requirements and in all grades and standards
we have various range of EYE NUTS in ready stock size M6-M100 and more as per client requirements and in all grades and standards
Nanak shah Impex, We are supplier of all types fasteners.like Hex nut ,Hex bolt, Plan Washer ,Spring washer etc.
Brass Hex Nuts are used to connect both metal and wood components. They are also used in conjunction wiith brass bolts, screws, studs, threaded rod and any other brass fastener that has machine screw threads. Brass will protect against tarnishing and corrosion.Brass bolts also require a pilot hole be driven before installtion. Check out more information on brass as well as the other materials we offer.
Chhajed Steel and Alloys is one of the prominent producers of Monel 400 Bolts, which is a nickel-copper compound (around 67% Ni â?? 23% Cu) that is invulnerable to ocean water and steam at high temperatures and besides to salt and acidic strategies. We make Monel 400 Hex Bolts to your custom nuances, and we affirmation to meet your vehicle plan. Monel 400 Heavy Hex Bolts has remarkable mechanical properties at underneath zero temperatures, can be utilized as a bit of temperatures up to 1000�° F, and its consolidating point is 2370-2460�° F. Our thing degree of Monel 400 Hex Cap Screws discovers its utilization in different mechanical undertakings. An unprecedented average for Monel 400 Hex Screws is that they offer outstanding security from hydrofluoric dangerous, an especially uncommon ruinous to regulate, in all focuses up as far as possible. Tremendous utilization of Monel 400 Socket Cap Screws is made in the alkylation units, to be unequivocal in the responding zone in contact with concentrated hydrofluoric dangerous. The Monel 400 Machine Screws is utilized as a bit of the going with applications: Marine gadgets, siphons, valves and directing frameworks for ocean water applications, and so on. Monel 400 Allen Cap Screws are in like way utilized as a bit of Monoethanolamine (MEA) reboiling tube; Cladding for the upper zones of oil treatment office disagreeable areas; Propeller and siphon shafts and that is only a look at something bigger. Like with monetarily unadulterated Nickel, Monel 400 Square Bolts is low in quality in the strengthened condition, along these lines an accumulation of tempers are utilized to accomplish higher quality levels. Purchase Alloy 400 stuns at sensible rates from us.
Kamlesh Steel Industries offers Single Ferrule, Double Ferrule type Male / Female Connectors, Unions, Bulk Head Unions, Cross, Elbow, Tee, Tube Plug and Tube Cap in various sizes. M.O.C: SS304, SS316, Brass. Sizes: 1/8? to 1? OD (Suitable for Tube End) 4mm to 25mm OD (Suitable for Tube End) End Connections: NPT / BSP / BSPT / UNF Rating: 1500, 3000, 6000, PSI.
We are the recognized manufacturer of the buttweld fittings manufacturers. We provide you a variety of buttweld pipe fittings that are going to be praised worldwide for its high level of strength. Our product is highly durable and can also easily fit to any dimension due to the availability of different shapes and sizes. Moreover You would get amazed after knowing that all the sorts of buttweld fittings are present at highly competitive price. Also offers seamless buttweld fittings, stainless steel buttweld fittings, industrial buttweld fittings, carbon steel buttweld fittings, duplex steel buttweld fittings and alloy steel buttweld fittings..
SS Nuts / Collar Nut Hex nuts Size : M12 to M90 HSFG nuts Size : M12 to M90
Hex nuts Size : M12 to M90
