Spare parts, replacements, tires for agricultural and construction machineries, such as tractors, harvesting combines, trucks, bulldozers, excavators.All trade service are available.
HSS TANGENTIAL CHASERS LANDIS TYPE (SET OF 4 PCS) 2.1/8 INCH x 15/16 INCH - USD 60.00 3 INCH x 1.3/64 INCH -------USD 60.00 4 INCH x 1.3/64 INCH -------USD 80.00 4 INCH x 1.7/64 INCH -------USD 80.00 4 INCH x 1.1/4 INCH--------USD 120.00 5 INCH x 1.1/2 INCH -------USD 380.00 5 INCH x 2.1/4 INCH -------USD 280.00 All the above said prices are for Free Delivery Worldwide to any Country.
METRIC TAPS SIZE FROM M 4X.7 TO 60 X 5.5 INCHES SIZE FROM 1/8"TO 2.1/2" BSW, BSF, UNF, UNC BA 0 BA TO 4 BA .
M 10 TO M 24 SIZE AVAILABLE WITH US 3/8" TO 1" Trapezoidal Tap is the metric equivalent of Acme Taps but has a 30 degree included angle.
Design criteria: A - mill size or cutting diameter B - shank diameter C - length of cut or flute length D - overall length Angular Edge - That cutting edge that is a straight line, forming an angle with the cutter axis. The surface produced by a cutting edge of this type will not be flat as is the case with a helical cutting edge. Axial Run out - The difference between the highest and lowest indicator reading taken at the face of a cutter near the outer diameter. Chamfer - A short relieved flat installed where the periphery and face of a cutter meet. Used to strengthen the otherwise weak corner. Chip Breakers - Special geometry of the rake face that causes the chip to curl tightly and break. Chip Splitters - Notches in the circumference of a Corn cob style End mill cutter resulting in narrow chips. Suitable for rough machining. Core Diameter - The diameter of a cylinder ( or cone shape with tapered End mills) tangent to the flutes at the deepest point. Counter bore - A recess in a non-end cutting tool to facilitate grinding. Cutter Sweep (Run out) - Material removed by the fluting cutter (or grinding wheel) at the end of the flute. Cutting Edge (A) - The leading edge of the cutter tooth. The intersection of two finely finished surfaces, generally of an included angle of less than 90 degrees. Cutting Edge Angle - The angle formed by the cutting edge and the tool axis. Differential pitch cutters - A specifically designed variation in the radial spacing of the cutter teeth. This provides a variation in tooth spacing and can be beneficial in reducing chatter. This concept is based on reducing the harmonic effect of the tool contacting the part in an exact moment of vibration. Entrance Angle - The angle formed by a line through the center of the cutter at 90 to the direction of feed and a radial line through the initial point of contact. As this angle approaches 90 degrees the shock loading is increased. Entrance Angle: Ramp-in - Angle or radius value to enter the cutter into the part surface Fillet - The radius at the bottom of the flute, from which core diameter is found. Flute - Space between cutting teeth providing chip space and regrinding capabilities. The number of cutting edges. Sometimes referred to as "teeth" or "gullet". The number on an end mill will determine the feed rate. Flute Length - Length of flutes or grooves. Often used incorrectly to denote cutting length. Shank - Projecting portion of cutter which locates and drives the cutter from the machine spindle or adapter Straight Shank - Cylindrical shank, with or without driving flats or notches, often seen on carbide end mills Weldon Shank - Industry name for a specific type of shank with a drive and location flat. The flat on the cutter provides positive ( non slip ) driving surface to the End mill. Tooth - The cutting edge of the End mill. Tooth Face - Also known as the Rake Face. The portion of the tooth upon which the tooth meets the part. END MILL TECHNICAL FEATURES Back taper - A slight taper resulting in the shank end of the cutting diameter being smaller than the cutting end. This condition aids not only the plunging or drilling condition but also tends to compensate for deflection. Clearance - Space created by the removal of additional tool material from behind the relief angle. Clearance Angle - The angle formed by the cleared surface and line tangent to the cutting edge. Clearance: Primary (1st angle, 5°-9°) - Relief adjacent to the cutting edge. Clearance: Secondary (2nd angle, 14°-17°) - Relief adjacent to cutting edge Clearance: Tertiary (3rd) - Additional relief clearance provided adjacent to the secondary angle. Concave - Small hollow required on the end face of an End mill. This feature is produced by a Dish angle produced on the cutter. Convex - An outward projection radius feature on the end face of a Ball mill. Dish Angle - The angle formed by the end cutting edge and a plane perpendicular to the cutter axis. Dish ensures that a flat surface is produced by the cutter. Gash (Notch) - The secondary cuts on a tool to provide chip space at corners and ends. The space forming the end cutting edge, which is used when feeding axially. Gash angle - The relief angle of the gash feature. Gash width - The width of the gash feature. The space between cutting edges, which provides chip space and retargeting capabilities. Sometimes called the flute. Heel - The back edge of the relieved land. It is the surface of the tooth trailing the cutting edge. Helical - A cutting edge or flute which progresses uniformly around a cylindrical surface in an axial direction. The normal helical direction is a right direction spiral. Helix Angle - The angle formed by a line tangent to the helix and a plane through the axis of the cutter or the cutting edge angle which a helical cutting edge makes with a plane containing the axis of a cylindrical cutter. Hook - A term used to refer to a concave condition of a tooth face. This term implies a curved surface rather than a straight surface. Hook must be measured at the cutting edge, making measurement difficult. Land - The narrow surface of a profile sharpened cutter tooth immediately behind the cutting edge, (A) Cylindrical - a narrow portion of the peripheral land, adjacent to the cutting edge, having no radial relief. (B) Relieved - A portion of the land adjacent to the cutting edge, which provides relief. Lead - The axial advance of a helical cutting edge in one revolution. Lead = (Cutter diameter x Pi) / Tangent Helix Angle Length of Cut (Flute Length) - The effective axial length of the peripheral cutting edge which has been relieved to cut. Radial Rake angle - The angle made by the rake face and a radius measured in a plane normal to the axis. Rake - The angular relationship between the tooth face or a tangent to the tooth face at a given point and a reference plane or line. An angular feature ground onto the surface of an end mill. Axial rake - The angle formed by a plane passing through the axis and a line coinciding with or tangent to the tooth face. Effective rake - The rake angle influencing chip formation most is that measured normal to the cutting edge. The effective rake angle is greatly affected by the radial and axial rakes only when corner angles are involved. Helical rake - For most purposes the terms helical and axial rake can be used interchangeably. It is the inclination of the tooth face with reference to a plane through the cutter axis. Negative Rake - Exists when the initial contact between tool and work piece occurs at a point or line on the tooth other than the cutting edge. The rake surface leads the cutting edge. Positive Rake - Exists when the initial contact between the cutter and the work piece occurs at the cutting edge. The cutting edge leads the rake surface. Relief-Space - Provided by removing material immediately behind the cutting edge. Done to eliminate the possibility of heeling or rubbing. Axial angle relief - The angle made by a line tangent to the relieved surface at the end cutting edge and a plane normal to the axis. Axial relief - The relief measured in the axial direction between a plane perpendicular to the axis at the cutting edge and the relieved surface. Helps to prevent rubbing as the corner wears. Concave relief - The relieved surface behind the cutting edge having a concave form. Produced by a grinding wheel set at 90 degrees to the cutter axis. Eccentric relief - The relieved surface behind the cutting edge having a convex form. Produced by a type I wheel presented at an angle to the cutter axis. End relief - Relief on the end of an end mill. Needed only for plunging cutters and to relieve rubbing as the result of corner wear. Flat relief - The relieved surface behind the cutting edge having a flat surface produced by the face of a cup wheel. Radial relief - Relief in a radial direction measured in the plane of rotation. It can be measured by the amount of indicator drop at a given radius in a given amount of angular rotation. Tangential rake angle - The angle made by a line tangent to a hooked tooth at the cutting edge and a radius passing through the same point in plane normal to the axis. 2mm to 14mm 25piece pacing. 15mm to plus single piece packing.
Plain Type,60 degree included angle,right-hand cut Made from super speed steel,bright finish. This tool is used for centering work ends,where the work-piece is to be revolved on machine centers. 60 degree countersink angle fits all standard centers. 25 piece packing and single piece packing.
Size available as per your request.
Showcasing a building, emphasizing a lobby or creating an illusion of openness, the Kalsi all glass Automatic Slide Entrance allow the beauty and elegance to show through the entrance area with a clear line of sight unhindered by vertical stile. This entrance creates and unobstructed view of either the interior or exterior of a building while providing the smooth quiet and reliable operation that is the standard for the industry Advanced Features When anybody touches the door during closing operation, the door will go back immediately without any accident. Easy to install. High safety, when contact with objects, human body, the door will draw back immediately. Accessibility: in case of power cut the door can open easily and close also by females and kids with a light push upto 4.5kg. Low faulty rate, easy & fast to maintain. Gear style activating belt and accurate conveyance High Efficiency Micro Computer Control Set The micro computer unit will remain at the top of the door. It has easy provision to control/setup the speed of opening and closing of the door etc. Suitable Area Various offices, Buildings, Residence, Commercial Blocks, Banks and Hospitals etc
The sliding gate operators are used to drive sliding Gates for Industrial, Commercial and residential uses. The operators can be fitted with gear wheel or chain wheel and featured with powerful starting strength, capable of overwork at short time. In case of power failure, an emergency release key allows to operate the gate manually Advance Features Gear-driver or Chain-driver is optional. Magnetic or Spring limit switch is optional. The self-locking electromechanical gearmotor Keeps the gate completely closed. Motor torque adjustment Stop on closing if it hits obstruction. Overheat & Overload dual protection. Emergency release key in case of power failure. Control panel wiring are available to safety device, alarm lamp and remote controller. Available in 240 DC version, which can be operated by storage battery
ADVANCE FEATURES Driver: The driver case is made of Aluminium-Alloy by casting die and has good sealent. Two step worm give the Drive a large Torque of Output and lower noise. There is a frictional clutch in it to prevent the overload of the Driver and DC motor. Electric Control Box: The working command of the Driver is coming from the buttons on the Electric Control Box or the transmit. There are three buttons on it and the irrespective three components - Open, Close and Stop. The protection system can be protected the men and other things which just through the door of overloaded with the DC motor. Remote Controller: The Remote Controller can be divided in teo parts- Transmitter and receiver. Only the variable cryptographics are the same in the transmit and receiver and distance is less than 100m. There are 1024 variable cipher code to choose from. Electric Lock: The command had no sooner reached the Electric Control Box and the Electric Lock than door began to move. If the powers fail, you can use the key to open the electric lock
This model is fully secured from current leakage and Electro-mechanical Limit. The angel of barrier arm may be adjusted from 75¦ to 90¦. The control system may be fitted with wiring terminals for ticket dispenser and Alarm Lamp. In case of power failure barrier can be operated manually Advance Features 1. Self-locking electro-mechanical gearmotor 2. Built-in control panel. 3. Adjustable balancing system. 4. Base plate and brackets for floor installations. 5. Auto-stop function if it hits obstruction. 6. Folding arm is available for lower roof. 7 manual operate system in case of power failure
This operator can slide upward with weight of rolling shutter upto 25kg (size upto 3 meters height and 5.5 meter width) Technical Specifications Installation View Remote Control - two remote transmitters equipped for operation from distance up to 30-50 meters. Automatic Reversing System - ensures the door returns to an open position when it meets with an obstruction while in closing mode. Courtesy Light - light automatically when door is in use. The light will stay on for approximately 3 minutes then turn off automatically. Easy Manual Disengagement Pull Cord - just pull on cord once to disengaged operator for manual operation in case of power failure. Auto Close Mode - set your garage door to automatic close 30 seconds after opening. An infrared beam must be installed if this mode is selected. Safety Infrared Beam - can be fitted to the unit for extra safety protection. Must be fitted for auto-close mode to function. Open and Close Buttons - built in the unit to help you set the open and close limit positions more quicker and precise. Auto Run Time - If the motor is left running in the operator for any reason, the Auto Run Time will turn the motor off after 60 seconds. CAS ( Color Assisted Settings ) System - makes it easier and quicker for the user or installer to complete the installation
Scaffolding products like props, jacks, pole line hardware, strut, metal products.Manufacturer & exporter
Hand tools, scaffolding equipments, automobile parts..
Threaded bar, nut, bolt, scaffolding stainless steel.
Scaffolding couplers.
Scaffolding, shoring, formwork and fasteners.
Couplers, rings lock.
Wrought iron product, scaffolding.
VIKAS INDUSTRIES are Indian manufacturers exporters of Wrought iron components, wrought iron hardware for gates, wrought iron fence gate hardware panels, wrought iron gates accessories parts, wrought iron products and accessories, ornamental iron gates hardware accessories parts, ornamental iron fence hardware materials, wrought iron fencing hardware, decorative metal fencing panels and accessories, decorative metal fence posts, railing hardware components, wrought iron railings and hardware parts, wrought iron railing for stairs, gate grill hardware parts, decorative wrought iron railing manufacturers exporters
