There is no doubt that continuous waste plastic pyrolysis plant is based on batch equipment design, so their main pyrolysis process is consistent with the principle, the latter is only more intelligent and easier to operate, which also reduces the more manpower and material resources. Its main advantage over small pyrolysis equipment is that it can continue to work 24 hours a day. There is no need to stop in the middle because of loading and unloading or cooling, which can save a lot of time and make the whole process more efficient. First of all: Put the collected plastic products into the plastic crusher and crush the waste plastic. This will not only save space but also accelerate the reaction speed of waste plastics in the furnace, and in short, it can improve the operating efficiency of the equipment. Secondly, the broken waste plastic is fed into the reactor through a pusher and the reactor is heated. The temperature of the reactor reached a certain height, and waste plastic pieces cracked out of oil and gas, carbon black. Once again, the oil and gas that has been cracked enter the condensing system. When the hot oil and gas meets cold, it is liquefied into heavy oil and falls into the oil tank. Then: For the treatment of the three wastes of waste gas and waste water generated during the operation of the equipment, the company launched a desulfurization and deodorization tower system to thoroughly help customers solve the problem of factory odors and meet European and American environmental protection and emission standards. Finally, the carbon black be outputed. Advantages of continuous pyrolysis equipment: 1. The PLC control system can improve equipment operating efficiency.Because it can continuously feed materials continuously for 24 hours. Great savings in manpower and material resources. 2. The single machine processing capacity is large and the floor space is small, saving the cost of purchasing land in the previous period. 3. Use an accurate calculation system to ensure that the feed is fully cracked and the oil yield is high. 4. Indirect heating system, long service life. The end products of DoingGroup's continuous waste plastic cracking equipment mainly include fuel oil, carbon black and combustible gas. Their specific uses are as follows: 1. Fuel: Mainly used for heating oil in iron and steel plants, and boiler plants. It is also commonly used in heavy oil generators to generate electricity. 2. Carbon black: Carbon black briqutting can be produced for burning, refining from carbon black , can be produced for new tires, and pigment manufacturing materials.
scrap metal chrusher is a professional equipment to crush metal cans into the required size from 10-30mm. Metal scrap processing machine is mainly used for waste recycling field. Our scrap metal crusher machine is used for scrap cans recycling in large-scale recycling centers, which is collecting cans, paint bucket etc. The scrap metal chrusher machine has the advantages of high yield, low energy consumption, high efficiency, the material is crushed uniformity. It is low noise, no pollution, simple operation and easy maintenance etc. scrap metal chrusher machineis in the use of hammer to strike with high speed and high torque of the motor driving, Scrap metal cans will come from the top opening into the crushing chamber, in the crushing chamber, there are durable lining board and hammers and rotor, the high-speed rotating can extrude,tear,impact,and grind scrap metal cans into small granules, then discharged from the bottom of the sieve plate with changeable mesh size according to crushing size.
The DoingGroup's waste plastic cracker is a high-temperature pyrolysis chemical reaction performed in an oxygen-free environment. This reaction can reduce the bulk of macromolecular compounds, waste plastics or other organic solids into small pieces. Molecular compound. Of course, in addition to waste plastics, you can use this cracking device to treat other organic solids, such as waste tires, waste rubber, and other organic solid waste. The Dongying Group has always been committed to the research and development of refining equipment and has made its contribution to the industry second to none. With the maturity of the domestic market, DoingGroup has turned its sights around the world and established an office in Thailand. At the same time, we have The cracking equipment is also known and sought after by people in various countries around the world. The DoingGroup's waste plastic cracking equipment is so popular because of its high oil output rate. Our equipment has different capacities. Taking 10 tons of equipment as an example, 4.5 tons of fuel can be obtained in one day of operation. According to the conservative calculation of the value of fuel in the market, a day's worth of 1,800 dollars will be obtained for the fuel produced by the equipment. Of course, this benefit does not include carbon black and the income of steel wire. So why did the DoingGroup's cracking equipment have such a high oil output rate? First of all, DoingGroup's waste plastic cracking equipment is designed with a vacuum device, which can provide negative pressure and drain oil and gas. This device ensures that even if the oil and gas are not fully condensed in the condensing system, they will pass through the pressure and be filtered again in the condensing system until the oil and gas are fully filtered. Second, use the most advanced and most effective condenser in the industry. This type of condenser uses column tube condensation, also known as a three-stage cooling system, which ensures that the cracked oil and gas is fully cooled and the oil yield is high. Finally, the DoingGroup's cracking equipment has oil-water separators. It not only can purify oil and gas, and separates water from oil and gas, but also can prevent the backflow of oil and gas and increase the oil yield. Contact: Ms Bonnie Phone: +86-371-5677 1821 Mobile/Wechat/Whatsapp:0086-135-2669-2320 Skype: bonniezhao2 Email: oilmachine@doinggroup.com http://www.recyclingpyrolysisplant.com http://www.doinggroup.com
Old tire pyrolysis technology is a green technology that solves waste tire pollution to the environment. And can ease the energy crisis, in today's society, this is a very meaningful environmental protection industry. Tire pyrolysis oil is an end product extracted from the pyrolysis process and is often used to heat raw materials and generate electricity with heavy machinery. If the pyrolysis oil is subjected to a specialized pyrolysis oil distillation plant distillation, the extracted diesel oil can be used for diesel generators and light fuel oils. The main part of the entire pyrolysis system includes reactors, transmissions, catalysis rooms, cooling pipes, manifolds, heavy oil tanks, light oil tanks, condensers, oil-water separators, safety devices, vacuum systems, dust collection systems, etc. The main working principle of old tire refining equipment: By pyrolysis of the oil using a high-temperature distillation tire, the impurities in the oil are distilled off, and the filtered light oil vapor increases in heat, and impurities in the pyrolysis oil fall into the furnace. Light oil and gas passes through a multi-stage heating system, is filtered, enters a cooling system, is then liquefied, passes through a water separator, and flows into a light oil tank. After degreasing and desulfurization, clean and transparent diesel oil can be obtained. The average diesel yield is 80%-85%. Finally, the residue in the furnace is discharged from the furnace. It is a substance that functions like asphalt. The approximate yield of bitumen is: 15%-20%. The end product of the Dongying Group's used tire refining equipment was diesel oil and asphalt. What are their main uses? 1. Diesel: Mainly used for heavy machinery, generator power oil, and boiler heating combustion oil. 2. Asphalt: Mainly used for direct paving, or sent to asphalt refineries.
Tire Shredder is an important shredding machine in tire recycling and retreating process, TongLi tire shredder equipment is exclusively used in crushing scrap tire ,this product with the aim of break the tire into about 50Ã?50mm plastic blocks to facilitate the follow-up crushing process.It is the preferred machine for processing rubber tires.The main structure of the machine:Into the hopper,motor,drive system,shredders,rotating screen and other components. Tire Shredder machine-Application It is suitable for crushing large size,thick and hard materials, such as :plastic / rubber, tire, TV housings, car housings, washing machines and refrigerators, color steel tile, scrap metal, wood,, paint bucket, chemical bucket ,forklift pallet,Cables, IC boards ,aluminum , paper products, waste cloth, scrap furniture ,etc. Tire Shredder featuares 1. Dual cutter shaft design, low revolution and noise; 2. Helical Gear Reducer, large torque and strong power ; 3. Special steel cutter with high strength and long service life; 4. Combined design, easy to maintain. 5. PC control, automatic forward and reversal function.
Tire shredder is an important shredding machine in tire recycling and retreating process, Tongli tire shredder equipment is exclusively used in crushing scrap tire , this product with the aim of break the tire into about 5050mm plastic blocks to facilitate the follow-up crushing process.It is the preferred machine for processing rubber tires.The main structure of the machine:into the hopper, motor, drive system, shredders, rotating screen and other components. Tire shredder machine-application It is suitable for crushing large size, thick and hard materials, such as :plastic / rubber, tire, tv housings, car housings, washing machines and refrigerators, color steel tile, scrap metal, wood, , paint bucket, chemical bucket , forklift pallet, cables, ic boards , aluminum , paper products, waste cloth, scrap furniture , etc. Tire shredder featuares 1. Dual cutter shaft design, low revolution and noise; 2. Helical gear reducer, large torque and strong power ; 3. Special steel cutter with high strength and long service life; 4. Combined design, easy to maintain. 5. Pc control, automatic forward and reversal function.
Does the operation of DoingGroup's continuous pyrolysis plant difficult? It's easy!!! 1. Collect waste tires. 2. For the collected waste tires, put them in a wire drawing machine and extract the steel wire from the waste tires. 3. Place the tire with the wire removed into the tire crusher and break the waste tire into 3-5 cm pieces. 4. Put the tire chips into the continuous tire cracking equipment. After a multi-stage heating system and condensing system, fuel will be obtained. 5. After the cracked oil and gas are fully liquefied, the carbon black will be automatically discharged by the equipment after collection. DoingGroup's continuous tire pyrolysis plant can realize continuous processing of raw materials, so that "continuous feeding every minute and second, automatic slag discharge at all times, continuous oil discharge day and night"
With the development of science and technology and the progress of society, automobiles have become a must for people to travel. With the increase in cars, the number of used tires replaced is huge. Moreover, waste tires cannot be repaired again, otherwise it may cause serious traffic accidents. So how to deal with these waste tires, and to avoid re-contamination of the environment? DoingGroup has developed a waste tire pyrolysis plant. This pyrolysis plant is a process that cracks waste tires into fuel oil, carbon black, and steel wire using the principle of pyrolysis chemistry. So how does the waste tire pyrolysis plant work ? 1. There are two options for feeding collected waste tires into the reactor: (1) Feed the collected waste tires directly into the reactor via a pusher; (2) The steel wire in the waste tire is first drawn out with a wire drawing machine, and then the waste tire is sent to the reaction kettle through the pusher device. This can reduce the damage of the wire to the reactor. 2. The reactor is heated with fuel or fuel. When the temperature reaches a certain height, the waste tire begins to crack into oil and gas. 3. The cracked oil and gas enters the condensing system and is liquefied into heavy oil and falls into the tank. The liquefied material will be recovered by the equipment and reused in the heating of the reactor. 4. Dust removal and deodorization of the heavy oil in the tank will result in fuel oil. 5. When the temperature of the reactor drops below 40 degrees, remove the carbon black (steel wire) from the reactor. The yield of various materials used for the operation of DoingGroup's waste tire pyrolysis plant is 45-50% for fuel, 30% for carbon black, 15% for steel wire, and 10% for non-condensable gases.
Equipment introduction: Four-shaft shredder is developed based on market demand products. It adopts automatic control of microcomputer (PC) to set automatic start-up, stop, reverse and overload reversing control functions. It is mainly used for shredding light and thin metal with certain strength and waste garbage to increase its packing density for transportation and re-use . Performance characteristics : 1. Large torque, high yield, no manic, resistant to wear, etc. 2. Can to sharply reduce chip processing of iron filings volume. 3. Chip, horizontal double roller crusher can make the chip drying, briquetting, smelting, and broken, in the early period of the chemical fire prevention materials handling and pneumatic conveying becomes easy. 4. To cut broken down strips of metal processing tool cutting, spiral, sheet of metal scrap. 5.This Scrap metal shredder is the idea machinery for Ferroalloy smelting, metal steel scrap, scrap iron, scrap metal and scrap recycling companies. 6. This scrap metal crusher machine can be equipped with conveying feeding device. Working principle and structure: Using of high-torque blades for physical cutting, tearing, sawing and other means in the closed silo to the initial shredding materials, and then Tongli original screening technology, screening out the size of the material to meet the requirements; does not meet will automatically back to the material Continue processing. Application field: Metal shredder is widely employed to crush paint bucket, discarded appliances shell (plastic shell, metal shell), large pipes, pipe fittings, forklift pallets, tires, drums, aluminum and copper, as well as being used to crush iron sheet, scrap circuit board,and so on. Applicable material range: Paper making derived waste, cartons, paper rolls, wood; · Plastic barrels, plastic electrical shell; Metal cans, thin-walled metal buckets, metal shell of appliances; � circuit boards, mixed light industrial waste; Carpets, woven bags, household garbage sieve; Light construction waste, medical waste; Biomass and alternative fuel preparation industries; Particularly suitable for crushing the particle size of the higher applications; Broken material is smaller or medium-sized uniform size sheet.
According to incomplete statistics, China has more than 80 million motor vehicles, more than 100,000 ships, and nearly 300,000 fishing boats. The only three oils that need to be replaced each month amount to more than four million tons. In large scale, there is very little recycling, and most of the replaced waste engine oil is dumped or burned on the spot, which wastes a lot of resources and causes serious environmental pollution. In order to promote the development and utilization of renewable energy, increase energy supply, improve energy structure, ensure energy security, protect the environment, and achieve sustainable economic and social development. The DoingGroup's R&D team has developed waste oil refining diesel oil machine. The equipment mainly uses high-temperature distillation and condensation to heat and distill the waste oil at room temperature. A part of the oil and gas enters the condensing system and is liquefied into the oil tank. The non-liquefiable part is sent to the heating system through the gas system to burn off. The main working flow of waste oil refining diesel oil machine is: 1. The heat transfer oil system adds heat transfer oil and heats the base. 2. The base of the reactor is heated. The aircraft is subjected to high temperature distillation and the oil is distilled off. 3. The oil and gas passes through the tower and enters the condenser. The liquefiable portion is condensed into product oil. The non-liquefiable portion is sent to the heating system through the gas system and burned. 4. The final product oil obtained is desulfurized and degreasing. The main advantages of this waste oil refining diesel oil machine are as follows: 1. The reactor adopts a vertical design instead of the traditional horizontal design, which is more conducive to slagging. 2. With double heating system, both base heating and heat conduction system preheating, fast heating, save time. 3. The standard refined diesel is tan-yellow. If you want to get a better color of diesel, we can also provide a deep purification system, and finally get a pale yellow diesel product.
The continuous process tire pyrolysis plant is an innovation of the intermittent waste tire cracking equipment. It has realized uninterrupted 24-hour continuous feeding, continuous out puting, saving manpower and material resources, and improving efficiency. The main work flow of continuous process tire pyrolysis plant is as follows: 1. Withdraw the collected tires with a wire drawing machine. 2. Put the wire pulling tire into the tire crusher and break the tire into small pieces of 3-5cm. 3. Put the tire scrap into the continuous process tire pyrolysis plant and heat the reactor. After much and pyrolysis reaction and condensation finally get fuel. 4. The end of equipment operation will be automatically discharged carbon black. What are the main advantages of continuous process tire pyrolysis plant? 1. Relative to the intermittent tire cracking equipment, the single machine processing capacity is large and the floor space is small. 2. Use plc control system to save manpower. 3. An accurate calculation system ensures that the waste tire can be fully cracked and the oil yield is high. 4. The pyrolysis reactor adopts an internal rotation device and does not need to periodically stop the replacement of the sealing material. Like the intermittent tire pyrolysis plant, the continuous process tire pyrolysis plant can crack fuel, carbon black, steel wire, and combustible gas. Their specific uses are as follows: 1. Fuel oil : mainly used in iron and steel plants, boiler heating, heavy oil generators, and cement plants. 2. Carbon black: it is mainly used for pressure ball combustion and refined milling. Refined flour can be used for new tires, rubber soles, and pigments. 3. Steel wire: mainly used for waste recycling and recasting. 4. Combustible gas: it will be recycled by the equipment and reused in the heating fuel of the reactor.
Have you heard of converting waste plastic into oil? That's right, DoingGroup already has a very mature cracking device that heats waste plastics at high temperatures to crack fuel, carbon black and combustible gases. Perhaps some people do not know too much about the waste plastic pyrolysis plant. The specific operating procedures for the equipment are as follows: 1. The waste plastic into the reactor by automatic push device. 2. Reactor with fuel heating, reaching a certain temperature, waste plastics began to crack into oil and gas. 3. These oil and gas will enter the condensing system, a part of which will be liquefied and flow into the oil tank. The other part will be liquefied through the condensing system to liquefy into heavy oil and flow into the tank. 4. The resulting heavy oil will be filtered through the dedusting and deodorizing device. Remove fumes, dust particles generated during combustion of the fuel. 5. Wait until the temperature in the kettle drops below 40 C and remove the carbon black from the kettle. Know the working principle of waste plastic pyrolysis plant, equipment may be more interested in the proceeds. After our engineers accurately test and run our equipment can get nearly one million yuan a day's revenue, these benefits mainly come from the equipment cracked the fuel and carbon black. They have a wide range of uses in life, as follows: 1. Fuel oil: Mainly used in steel plants, boiler heating, heavy oil generators, cement plants. 2. Carbon black: mainly used for pressure ball burning and refined milling. Which refined flour and can be used for new tires, rubber soles, pigment manufacturing materials. So what are the unique advantages of our equipment? Specifically the following points: 1.16mm, Q245R thick steel boiler plate, curved pressure head, can withstand high temperature and high pressure. 2. Unique 3-step welding process, longer service life. 3. Currently the most commonly used and best performing condenser in the oil industry. The cooling system of the equipment is divided into three stages to ensure that the cracked oil and gas is fully cooled and the oil yield is increased. 4. A water separator, water seal, vacuum devices and other safety devices. Can purify oil and gas, exhaust, to prevent its back. And can provide negative pressure, drainage of oil and gas. Through the above introduction, you have a further understanding of our waste plastics pyrolysis plant?
DoingGroup's pyrolysis plant for waste plastic recycling is the process of pyrolyzing waste plastic into fuel oil, carbon black and non-condensable gas under the condition of anaerobic environment and utilizing the chemical reaction of pyrolysis. DoingGroup's main operating temperature pyrolysis plant: 1. Use mechanical waste plastic to enter the reactor and close the inlet to prevent gas flow out. 2. Carbon, wood or fuel heating reactor, the reactor is generally 200-300 degrees began cracking reaction, when the waste tires vaporized into oil vapor. 3. Hydrocarbons entering the condensing system are liquefied into oil and collected in the tank unit. Our system has a negative pressure device, he can greatly improve the production of pyrolysis oil. 4. At atmospheric pressure can not be liquefied petroleum gas as fuel for combustion returned to the reactor, not only energy saving and environmental protection, 5. After the oil production is completed, the reactor will be cooled. When the temperature drops to 40 degrees, the carbon black will be removed automatically or manually. The main advantages of this pyrolysis plant for waste plastic recycling are as follows: 1. Reactor manufactured according to the standard, using 16mm thick boiler steel pipe and arc pressure head, can withstand high pressure and high temperature. 2 high standard 3-step welding process, not easy to crack, long service life. 3. Pinion rotation device, small power, no direct contact with the reactor, heat transfer less easily deformed. 4. The tertiary cooling system uses a tube condenser, also known as a heat exchanger, which is currently the most commonly used and best performing condenser in the oil industry. Can ensure that the cracked oil and gas fully cooled, high oil production. 5 safety device oil-water separator, water seal, vacuum device, to ensure the safe and efficient operation of equipment. The most commonly available fuel, carbon black, and non-condensable gases from the operating equipment are as follows: 1. Fuel oil : Mainly used in steel mills, boiler heating, heavy oil generating units, cement plants 2 carbon black: can be used for high-pressure ball combustion can also be used for refined toner. Refined carbon powder for new tires, rubber soles and pigments. 3. Non-condensable gas: The non-condensable gas generated during equipment operation is a combustible gas, which is generally recovered by the system and reused for heating the fuel in the reactor.
The advent of cars has greatly promoted the development of society and improved the quality of our life. But on the other hand, the waste tires produced by automobiles pose a huge threat to our living environment. DoingGroup has developed a waste tire pyrolysis plant, the pyrolysis plant is the use of high temperature cracking chemical reactions, the waste tires cracked into fuel, carbon black, steel wire, combustible gas process. The main workflow of the tire pyrolysis plant is as follows: 1. Use mechanical waste tires to enter the reactor and close the inlet to prevent gas flow out. 2. Carbon, wood or fuel heating reactor, the reactor is generally 200-300 degrees is the beginning of the cracking reaction, when the waste tires vaporized into oil vapor. 3. The hydrocarbons entering the condensing system are liquefied into oil and collected in the tank unit. Our system has a negative pressure device, he can greatly enhance the production of pyrolysis oil. 4.Liquefied petroleum gas that can not be liquefied under atmospheric pressure is returned to the reactor as fuel for combustion, which is not only energy saving and environmental protection. 5. After the completion of oil production, the reactor will be cooled. When the temperature drops to 40 degrees, the carbon black and wires will be removed automatically or manually. The main advantages of waste tire pyrolysis plant are as follows: 1. Reactor press standard manufacturing, the use of 16mm thick boiler steel pipe and arc pressure head, can withstand high pressure and high temperature. 2 high standard 3-step welding process, not easy to crack, long service life. 3. Pinion rotation device, small power, does not directly contact the reactor, heat transfer less easily deformed. 4. The three-stage cooling system uses tube condensers, also known as heat exchangers, which are currently the most commonly used and best performing condensers in the oil industry. Can ensure that the cracked oil and gas fully cooled, high oil production. 5 safety device oil-water separator, water seal, vacuum device, to ensure the safe and efficient operation of equipment. The final product cracked by the waste tire cracker has a wide range of uses, mainly as follows: 1. Fuel: Mainly used in steel mills, boiler heating, heavy oil generating units, cement plants and so on 2 carbon black: can be used for pressure ball burning, can also be used for refined toner. Refined toner for new tires, rubber soles and pigments. 3. Steel wire: can scrap recycling, can also be re-cast into other steel. 4. Combustible gas: the system was re-collected for reactor heating.
DoingGroup's continuous waste plastic pyrolysis plant is a change of intermittent waste plastic cracking equipment, the use of automatic PLC control system, the real continuous feed, continuous discharge, 24 hours a day, without stopping the cooling and then Slag. Greatly improve the work efficiency, but also reduce labor costs. Continuous waste plastic pyrolysis plant, the working process includes three parts: waste tire pretreatment, continuous pyrolysis system, continuous feed, PLC control continuous discharge. Cracking is the use of high temperature heating, the waste plastics cracked into fuel, carbon black and combustible gas process. Specific workflow is as follows: 1. Collection of waste plastics: all kinds of plastic garbage, such as waste PE pipe, PP plastic, PS plastic, ABS plastic. 2. Broken plastic waste: plastic waste into the plastic crusher. In order to maximize the savings of manpower and material resources, the device can be connected directly to the continuous waste plastics cracking equipment feeding system. 3. Cracking waste plastics: Reactor heating with fuel, the temperature reaches a certain level, generating oil and gas. After passing through the multistage pyrolysis reactor system, some of these hydrocarbons are liquefied into heavy oil and fall into the heavy oil tank. The other part enters the condensing system and liquefies into fuel. Carbon black will be automatically expelled at the end of the system. The main advantages of continuous waste plastic pyrolysis plant are as follows: 1.PLC control, high degree of automation, saving manpower. Truly a continuous feed, continuous discharge, 24 hours of uninterrupted operation. The entire project only needs to be equipped with 1-2 workers. 2. Large capacity, small footprint. To 20-30T tons of machines, for example, covers an area of only 600-700 square meters. And according to customer needs we can customize the capacity of 10T-100T equipment. 3.Indirect heating, long service life. 4. Pyrolysis reactor with internal rotation device, without regular pause to replace the sealing material.
Continuous tire pyrolysis plant is a new type of pyrolysis plant developed by DoingGroup on the basis of intermittent pyrolysis plant. The equipment adopts PLC control system and can feed continuously for 24 hours and continuously discharge slag. It is a continuously operated pyrolysis production line. Meet customer requirements for refinery efficiency. Continuous Tire pyrolysis plant Workflow: 1. The waste tire through the wire drawing machine out of waste tires in the wire. 2. Put the drawn steel tire into the tire crusher and break the tire into pieces. 3. The broken tire fragments into our continuous type of equipment, no longer need any operation, the device can automatically generate fuel. 4. Cracked carbon black, the system will automatically discharge the other end. The main advantages of continuous tire pyrolysis plant: 1. Accurately calculate the system to ensure full cracking, high oil yield. Indirect heating, long service life. 3. Continuous feeding, continuous slagging, saving time and effort. 4. Automatic, PLC control, save manpower. 5. Pyrolysis reactor with internal rotation device, without the need for regular pause to replace the sealing material. 6. Single handling capacity, small land area. Contact: Ms Bonnie Phone: +86-371-5677 1821 Mobile/Wechat/Whatsapp:0086-135-2669-2320 Skype: bonniezhao2 Email: oilmachine@doinggroup.com http://www.recyclingpyrolysisplant.com http://www.doinggroup.com
Plastic products, there are all aspects of our lives, on the one hand he brought convenience to our life; the other hand, from a variety of waste plastic generated garbage, but also to our living environment hazards. Based on the intermittent plastic pyrolysis plant, DoingGroup has developed a new type of fully automatic plastic pyrolysis plant. The equipment uses a precise calculation of cracking system, high degree of automation, continuous feeding, continuous slag discharge, 24-hour non-stop Run, without stopping the cooling and then slag. Working process: 1. The first plastic waste into plastic crusher, crushed waste plastic processing. 2. The broken plastic into the automatic continuous plastic cracking equipment. 3. Without any operation, you can get fuel. 4. Equipment produced in the reactor carbon black, will be automatically discharged at the end of the device. The main advantage: 1. Accurately calculate the system to ensure full cracking, high oil yield. Indirect heating, long service life. 3. Continuous feed. Continuous slag discharge, saving time and effort. 4. Automatic, PLC control, save manpower. 5. Pyrolysis reactor with internal rotation device, without the need for regular pause to replace the sealing material. 6. Single handling capacity, small land area. Contact: Ms Bonnie Phone: +86-371-5677 1821 Mobile/Wechat/Whatsapp:0086-135-2669-2320 Skype: bonniezhao2 Email: oilmachine@doinggroup.com http://www.recyclingpyrolysisplant.com http://www.doinggroup.com
Plastic products exist in all aspects of our lives, ranging from small plastic playground equipment to small plastic bags, the emergence of plastic will undoubtedly make our lives more colorful! But it is undeniable that waste plastic also brings a lot of trouble to our life. DoingGroup has developed a waste plastic cracking equipment, the use of high-temperature pyrolysis principle, the waste plastics cracked into fuel, carbon black, combustible gas process. DoingGroup's waste plastic cracking equipment workflow is as follows: 1. Use mechanical waste tires to enter the reactor and close the inlet to prevent gas flow out. 2. Carbon, wood or fuel heating reactor, the reactor is generally 200-300 degrees is the beginning of the cracking reaction, when the waste tires vaporized into oil vapor. 3. The hydrocarbons entering the condensing system are liquefied into oil and collected in the tank unit. Our system has a negative pressure device, he can greatly enhance the production of pyrolys is oil. 4, liquefied petroleum gas that can not be liquefied under atmospheric pressure is returned to the reactor as fuel for combustion, which is not only energy saving and environmental protection. 5. After the completion of oil production, the reactor will be cooled. When the temperature drops to 40 degrees, the carbon black and wires will be removed automatically or manually. Nearly RMB ten thousand yuan of revenue can be gained from running one of our equipment in a day, mainly from pyrolysis fuel and carbon black. They have the wide range use in dailylife: Fuel: Mainly used in steel plants, boiler heating, heavy oil generators, cement plants. Carbon black: mainly used for pressure ball burning, refining flour. Which refined flour and can be used for new tires, rubber soles, pigments of raw materials. DoingGroup's fee plastic cracking equipment is so popular, high oil yield, high yield is one reason, but also because of the following advantages of the device: 1. Reactor is produced according to the pressure vessel production standards, using 16mm thick boiler special steel and arc pressure head, can withstand high temperature and pressure. 2. High standard 3-step welding process, not easy to crack, long service life. 3. Pinion rotation device, small power, does not directly contact the reactor, heat transfer less easily deformed. 4. The tertiary cooling system uses a tube condenser, which is the most commonly used and best performing condenser in the oil industry. Make sure that the fuel vapor is sufficiently cool and produces high amounts of oil. 5. Safety devices have oil-water separator, water seal, vacuum device. To ensure safe and stable operation of equipment. Contact: Ms Bonnie Phone: +86-371-5677 1821 Mobile/Wechat/Whatsapp:0086-135-2669-2320 Skype: bonniezhao2 Email: oilmachine@doinggroup.com http://www.recyclingpyrolysisplant.com http://www.doinggroup.com
With the improvement of living standards, the car has become one of the essential means of transport for people traveling. On the one hand, it brings great convenience to our life. On the other hand, the waste tires on the car also pose a great threat to our living environment. In response to this serious social problem, DoingGroup uses pyrolysis principle to crack waste tires into fuel oil, carbon black, steel wire and combustible gas. Waste tire pyrolysis equipment by people from all walks of life at home and abroad more and more attention and praise. Our waste tire pyrolysis is so popular because it has the following advantages: 1. Our pyrolysis reactor is made according to the pressure vessel production standards, using 16mm thick boiler special steel and arc compression head, can withstand high pressure and high temperature. 2. High-standard 3-step welding process, not easy to crack, long service life. 3. Pinion rotation device, power is small, not directly contact the reactor, less heat transfer, not easy to deformation. 4. The three-stage cooling system uses tube condensation, also known as a heat exchanger, and is currently the most commonly used and best performing condenser in the oil industry. Can ensure that the cracked oil and gas fully cooled, high oil yield. 5. Our equipment has the following safety devices: water separator, water seal, vacuum device. They can prevent oil and gas from flowing backwards Pyrolysis, also known as pyrolysis, pyrolysis, pyrolysis, pyrolysis, refers to the pyrolysis of organic matter in an oxygen-free environment, and is a chemical process that converts one sample to another. Waste tire pyrolysis equipment is the process of pyrolysis of waste tires into oil, non-condensable gases and carbon black and steel wire by heating at high temperatures. The final product of waste tire cracker is fuel oil, carbon black, steel wire and combustible gas. These materials have a wide range of uses in our life and can be used in a variety of industries. Fuel oil : Can be used in steel mills, cement plants, boiler heating, heavy oil generator combustion heating. Carbon black: can be used for pressure ball burning, and refining flour. Which refined flour and can be used for new tires, rubber soles, pigments of raw materials. Steel wire: Can be used for scrap recycling and re-casting. Combustible gas: will be recycled back to the equipment for reactor heating. Our equipment has different specifications, designed for each customer's different needs of different capacity, customers can choose according to their needs and budget. Any questions about the machine, please feel free to contact us. -
According to statistics, in 2013, the amount of waste tires produced in China was 10.18 million tons, and it is estimated that more than 20 million tons will be exceeded in 2020. Where is the growing number of used tires? In response to this social problem, DoingGroup used chemical cracking reactions, R & D out of waste tire cracking equipment. Our waste tire refining equipment, by more and more people's attention, every day from around the world to visit our factory visit our equipment, our equipment is so popular, is Because of its following advantages: 1. Reactor is produced according to the pressure vessel production standards, the use of 16mm thick boiler steel pipe and arc pressure head, can withstand high temperature and pressure. 2. High standard three-step welding process, not easy to rupture, long service life. 3. Pinion rotation device, small power, no direct contact with the reactor, heat transfer less easily deformed. 4. Three-stage cooling system with tube condenser, is the most commonly used in the oil industry, the best performance of the condenser. Make sure the fuel vapor is fully cooled and produces high volumes of oil. 5. Safety devices have oil-water separator, water seal, vacuum device. To ensure safe and stable operation of equipment. Refinery equipment process: 1, First of all, the waste tires from the feed door into the host reactor, close the feed door, sealed. Heat the main furnace with fuel coal or wood in the heating chamber. 2, When the temperature reaches 220 , oil and gas precipitation, into the buffer chamber, residual oil (containing some slag) sink to the residue tank. 3,Light oil automatically enters the cooling system, condensed into oil. 4 Non-condensable gas, it will return to the reactor, as the heating reactor fuel. After the above process, you can get fuel, carbon black, steel wire, combustible gas, which cracked the material from the waste tires has a wide range of uses: 1. Fuel oil can be used in steel mills, boiler heating, heavy oil power plants and cement plants to produce refined diesel for further processing and diesel generators, light fuels, heavy machinery. 2. Carbon black can be used for pressure ball burning, refined toner. Can be used for new tires, rubber soles, pigments made of refined toner. 3. Steel wire is mainly used for scrap recycling, and re-cast into other steel. 4. Combustible gas is mainly used for circulating heating reactor. Outstanding highlights of our equipment is energy saving, low investment and high yield. Market prospects will be more and more broad, any machine problems, please contact us !!!
