Electrical home appliances, cooker hood, chimney hood, electrical heaters, electrical ovens, electrical cookers, infrared heaters, electrical grills, quartz heaters.
Industrial heaters, thermocouples, temperature controllers, ovens, furnaces, heating elements, hot runner heaters.
Electric heater, solar water heater, radiator, wall-mounted boilers.
Gas stove, gas heaters, gas cooking range, electric & gas water heater.
POPULA Fan Y6-30 Boiler Centrifugal Induced Draft Fan High Temperature Resistant Fan Low Noise Fan Product Introduction: It is specially designed for boiler using , featured by high efficiency and low noise ,the fan is used for ventilation system to transport air without corrosive and adhesive materials . The temperature of the media shall not exceed 250â?? . PRODUCTS INFO: Type:POPULA Industrial Boiler centrifugal induced draft fan Y6-30 Brand:POPULA Electric Current:AC Power:0.75-18.5 KW Voltage:1HP/3HP 110V/220V/380V/440V/3KV/6KV Frequency: 50/60HZ Air Volume:655-14000 CMH Air Pressure:727-3226 Pa Speed:1850-2350 rpm Max Noise:
Our vibrating furnace chargers are a onestop effective solution to problems such as higher labor costs and hazards faced by furnace operators in foundries melting shops etc Such automation allows foundry men to work at a safe distance thus preventing injuries arising out of molten splash Our vibrating furnace charger facilitates rapid and quick charging of the furnace thereby allowing maximum utilization of the furnace Advantages Very fast as compared to manual charging Minimum heat loss No chance of direct exposure of manpower to the furnace thereby preventing dangerous accidents due to mental splash Prevent damage to the furnace
Electric Furnace Electric furnace AEMF120 Electric furnace AEMF120 is specially designed to be used to melt metal alloy (zinc alloy and tin alloy) for rubber mold centrifugal casting purpose. Features: Automatic control. Energy saving Insulated protection shield and head. Safety circuit to prevent overheated. Temperature rises rapidly. Automatic consistent temperature control. Appointment heating start/stop time. Casted iron crucible. Specification: Power: 9KW. Loading capacity: 80kg (zinc alloy) Temperature: 600 deg; C max. Electric furnace EMF120 Electric furnace EMF120 is specially designed to be used to melt zinc alloy and tin alloy for rubber mold centrifugal casting purpose. Features: Automatic control. Energy saving Insulated protection shield and head. Safety circuit to prevent overheated. Automatic consistent temperature control. Appointment heating start/stop time. Casted iron crucible. Specification: Power: 9KW. Loading capacity: 80kg (zinc alloy) Temperature: 600 deg; C max. Electric furnace EMF50 Electric furnace EMF50 is specially designed to be used to melt lead alloy, magnesium zinc alloy for rubber mold centrifugal casting purpose. Features: Automatic control. Insulated protection shield. Safety circuit to prevent overheated. Automatic consistent temperature control. Appointment heating start/stop time. Specification: Power: 6KW. Loading capacity: 50kg (lead alloy) Temperature: 600 deg; C max
This furnace is designed for thick film products firing, such as Hybrid IC, chip-R, SMD components terminal, LTCC, Stainless steel heater, PV thin film cell and other similar products. Temperature Range: Belt Material: Cr20Ni80 Firing Atmosphere: Dry and clean Compressed air. Heating Element heating board Cooling Mode: fan cooling. Temperature Zone: 6 Zones. Chamber Temperature Uniformity: Overall Dimension:
A deal of South Bend ovens, 15oven, at a cheaper price than the market. New stock, works with electricity
About Mini Blast Furnace A Mini Blast Furnace (commonly known as Mandir Bhatti or Shahi Bhatti) is a simple, time-tested and widely used system to produce secondary lead in India and many other countries. It is the most basic of all furnaces and a production system based on this technology has certain distinct characteristics such as: Low Project Capital Cost Low Energy Cost (wooden coke fired) Easy to install Easy to operate & maintain Production of low Antimony Lead (soft lead) at low temperature Generates high pollution Description of Mini Blast Furnace The Furnace itself is a modified blast furnace which consists of a brick lined structure with fire brick oven in the midst and a metal Exo-skeletal structure outside. Raw material & fuel (coke) is charged manually through the side metal doors fitted in the brick structure and air is provided from the FD fans provided at the back of the brick structure. Molten metal & slag is tapped at the pits made in front of the brick structure and flue gases are sucked from the top of the brick structure which is provided with a metallic hood. A typical Double Oven Mini Blast Furnace has the following standard sizes & specifications: Outside Dimensions of Brick Structure: 2400mm L x 1900mm W x 2400mm H No. of Ovens: 2 Nos. Oven Size Top Dia: 600mm Bottom Dia: 250mm Depth: 650mm No. of FD Fans: 2 Nos. (1 for each oven) FD Fan Capacity: 300cmh at 250mm of WG No. of Charging Doors: 2 Nos. (1 for each oven) Charging Door Dimensions: 1100mm H x 650mm W Advantages No consumables used other than Wooden Coke which is also used as Fuel Low Power Consumption Produces low Antimony Lead suitable for soft lead purposes Pollution can be controlled with minimum fugitive emissions Easy to install, operate & maintain Disadvantages Cannot recover 100% lead in the first operation Subsequent recovery of lead after first recovery consumes higher coke & manpower. Equipment cannot be scaled up for higher production capacities. Air Pollution Control System for Mini Blast Furnace Various types of lead present in used batteries, plates and paste of lead oxide are charged in the furnace. In addition to these, certain compounds of sulphur are also present in the batteries. When this material is heated in the presence of carbon, lead oxide is converted to lead. This conversion along with burning of fuel generates flue gases and fumes containing dust, dirt, oxides of lead, lead particles and other impurities etc. Hence, to meet various goals of maintaining employees' health, for factory environments as well as regulatory requirements, it becomes imperative to get high end Air Pollution Control Systems to be installed with the Mini Blast Furnaces.
Xinology GTF Series Glass Tempering Furnaces Are Used To Induce Stress On Glass Surfaces By Thermal Process This type of furnace is also named as glass thermally tempering furnace. Glass strength is increased compared with ordinary glass. Tempered, or also known as toughened glass, will usually shatter into small fragments instead of sharp shards when broken. These small cuboid fragments are less likely to cause injury. Xinology glass tempering furnaces also produce heat strengthened glass or also known as half tempered glass which shatters in big clusters.
Vacuum Precision Casting Furnace Vacuum precision casting furnace is designed for Melting heat-resistant high-temperature alloy material,and Casting of Equiaxed under vacuumed condition as well as for directionally solidified (DS) or single crystal (SC) structures . Efficiency :Crucible Basket to ensure fast crucible exchange and continuous operation. Easy operation: Humanized operation interface; rotary tower charging and temperature measuring devices to freely switch between load charge material and read temperature.
Hyontec sf system curing furnace is widely applied to the surface drying and curing of the zinc-flake coating, alloy coating and outstanding sealant on electroplating industry. These are some reasons hyontec sf system is the no. 1 choice for the application of all above coatings. 1) dismounting & installation conveniently Both belt curing furnace and curing oven can supplied for you by your requirements Container
Usage â?¢� Used for artificial aging treatment of castings. Divided into car bottom and chamber types. � Technical Parameters â?¢ Maximum heating temperature: 250â?? â?¢ Furnace temperature uniformity: â?¤�±5â?? â?¢ Temperature control precision: �±1
Usage  Used for artificial aging treatment of castings. Divided into car bottom and chamber types.  Technical Parameters Maximum heating temperature: 250 Furnace temperature uniformity: ±5 Temperature control precision: ±1
Usage Used for artificial aging treatment of castings. Divided into car bottom and chamber types. Technical Parameters Maximum heating temperature: 250 Furnace temperature uniformity: ±5 Temperature control precision: ±1
Usage The equipment is mainly used for solution hardening and artificial aging heat treatment of aluminum alloy workpieces and the annealing heat treatment of aluminum alloys. Used for treatment of aluminum alloy T4, T5, T6, T7 and T8. Up to standard! The heat treatment of the aluminum alloy materials conforming to the US military standard SAE AMS 2772E-2008 The heat treatment of the casting aluminum alloys conforming to the Chinese aviation standard HB5446-90 The vertical aluminum solution-hardening furnace, also known as drop-bottom aluminum solution-hardening furnace, is a heating furnace for periodic heat treatment, used for production of ultrahigh-quality workpieces in the war, aerospace, automobile manufacturing and high-voltage electrical equipment industries. Small batch, high qualitythe best choice for solution treatment of aluminum!! Three performance guarantee parameters:  Furnace temperature uniformity: ±3 Temperature control precision: ±1  Workpiece transfer time: 6-15s  Equipment Features A patented self-locking mechanism is adopted for the furnace door, ensuring that the furnace door will not descend by itself under any circumstances.  There is a flexible sealing connection between the furnace door and the furnace body; the furnace door is pneumatically compacted, ensuring the synchronous sealing performance of the whole sealing surface.  Each mechanical action is equipped with a perfect self-locking function, ensuring operation reliability and safety. Especially, there is a well-designed logical relation and reliable hardware-software logic interlocking circuit among the heating system, fan operation system, furnace door switch system, charging basket lifting system, water tank movement system and mixing system. They can keep the equipment and thermal treatment device safe in case a sequence error is caused by manual operation or a failure occurs in an action process during automatic operations.  High furnace temperature uniformity. A large-flow and high-air-pressure heat-resisting fan is adopted, able to generate enough recirculating air quantity and pressure; the super-large furnace consists of multiple temperature control zones including one main zone, ensuring that temperature rises synchronously in all of the temperature control zones; the all-fiber furnace lining minimizes heat loss, ensuring that the furnace chamber temperature gradient is within a certain range. High furnace temperature control accuracy. Multiplex control maximally ensures that the furnace chamber does not overheat, thus protecting workpieces from being softened and over-burnt.
Heating energy sources: natural gas, liquefied petroleum gas (LPG). An imported famous-brand automatic burner or gas burner is adopted, ensuring high heating performance, low noise and zero-discharge of fume, meeting the environmental protection requirements. After heating, the hot furnace gas is blown back to the upper mouth of the crucible through the flue; or preheated the combustion air from the flue heater ex-changer to improve the heating efficiency and reduce fuel consumption. Multiple safety protection modes are adopted, such as gas under-pressure, assisted gas under-pressure, flameout alarm and so on. Melting rate in a cold furnace: 3.5h Melting rate in a heated furnace: 2h
Usage Mainly used for maintaining temperature of molten aluminum alloys, suitable for all the crafting processes, such as pre-aluminum casting degassing, alloy preparation, uniform structure and temperature regulation and so on. â?¢ Energy source can be electricity and gas. Equipment Features â?¢Higher-quality molten aluminum can be obtained. Molten aluminum temperature accuracy, composition uniformity and less hydrogen content can be guaranteed. Flexible production organization. The crucible can be replaced at any time for production of different types of alloys, without contaminating the molten aluminum. Low burning loss of aluminum. The aluminum in the crucible is heated with heat conduction of the crucible, without local high temperature, reducing oxidizing loss and high-temperature volatilization, lowering the burning loss of aluminum to a level below 1.2%. The furnace floor is molded by monolithic casting with a casting material. Moreover, at the bottom of the furnace is a leakage outlet, through which the molten aluminum can outflow once the crucible is broken, reducing the risk of damage to the furnace body. The temperature of the furnace chamber and molten aluminum is controlled by series circuit, ensuring sufficient heating efficiency and preventing overheating of the furnace chamber. The molten aluminum thermocouple protect tube is made from silicon nitride, which is well heat-conducting, resistant to corrosion by the molten aluminum, resistant to thermal and cold shocks and highly strong. The tube can be directly immersed in the molten aluminum to measure its temperature. It has a service life of more than 2 years. Multiple safety protection modes are adopted, such as molten aluminum over-temperature alarm, furnace chamber over-temperature alarm and crucible leakage alarm and so on.
We have stock of 400 MT Furnace Oil for sale
