Find Verified Rubber Coating Suppliers, Manufacturers and Wholesalers

Anti-slip coatings and treatments for every slippery

Desoprime is an epoxy polyamide primer of two components with zinc phosphate as a preventive dye of the corrosion. When dried completely it creates a rust - resistant ,high strength coating.It is used as an epoxy primer for general use according to the painting instructions.

Desmofen is an acrylic polyurethane coating with two-component poly-gloss aliphatic isocyanate hardening .It has remarkable gloss and colour-shade.It is used as a polished finish for alluminium ,steel ,reinforced polyester and wood in a highly corrosive atmospheric environment.

Desmopol Topcoat is a semi-acrylic polyurethane coating of two-components aliphatic isocyanate with good gloss .It is used as a final coating for the protection of structural steel in extremely corrosive environment, when light steadiness and preservation of the gloss is required.The minimum heat for drying is -10

Desmalkid Prime is a zinc phosphorus primer with an alkyd base which dries relatively quickly.It is usually used as a general purpose primer for Desmalkid Prime Systems for the protection of steel structures in mild to moderate corrosive atmospheres.

Desnamel 200 is a fast-drying zinc phosphorus primer with an alkyd base.It is an ideal primer to prevent rust in steel.It is also indicated for mechanical parts and where fast drying is required.

Desmozinc 500 is an epoxy polyamide primer of two components rich in zinc.When dried completely it creates a high strength coating very weather-resistant.It provides cathodic protection against local mechanical damage.It is used as an epoxy primer according to the painting instructions.

Desmepox 1000 is a two-component epoxy amine coating which when dried produces a coating whith excellent resistance to different chemical substances.It is used as an internal tank coating according to the painting instructions.

Fujimar 500 is an anti-colour to protect shells from shellfishes and grass adhesion.It is an ideal coating for plastic , wooden and iron boats and for speeds of up to 35 miles.Fujimar 500 presents a change in its colour when it is outide of the water due to its composition.

Fujimar 600 is an anti -colour to protect shells from shellfishes and grass adhesion.It is ideal for plastic , wooden and iron boats and for speeds of up to 50 miles.It does not change its colour when it is out of the water.It contains a new microbict by prolonging the protection of the boat in the water.

Desnamel Fast Dry is a fast -drying alkydic final coating with good gloss and preservation of hue.It is used as a primer as long as a final coating for steel in a slightly corrosive environment.

This is a special paint with extreme adhesion to glass surfaces. It is sprayed onto any type of glass to produce coloured glass panels.

Magic Pox is a crystal clear epoxy coating and casting resin
Magic Pox is a crystal clear casting and coating epoxy system that cures to a rigid, Moisture resistant, shiny high
gloss of crafts and decorative applications
Magic Pox finishes used for:
Coating Casting
Clear coating and sealing artwork Casting jewelry including earrings
Photography Pendants
Plaques and frames Necklace ring & Rings
Paper collages Figurines
Tabletops Coasters
Ideal for Both Casting and Coating
Perfect for starter beginner and professional artist
Cures crystal clear
Moisture resistant
Environment friendly (odor free and no solvent)
Rigid and high gloss finish
Self-leveling
Exceptional clarity
Natural air bubble release without the need for degassing
Hard wearing and highly polishable!
Excellent impact strength

Mix ratio by weight : 100 A : 25 B
Color Water clear
Solids Content 100 %
Specific gravity 1.1 ± 0.02
Working time Approx. 30 min. (at 23 C)
Substrate temp. Min 10 C , max 30C
Initial Curing time Approx. 24 h (at 23 C)
Fully cured 7 days (at 23 C)
Hardness, Shore D > 82
How to use
Surface preparation:
The surface must be clean, dry, and free of dust. The all damaged areas, cracks and surface irregularities must be
repaired and smoothened.
Mixing:
It is important to remember that this cast has a limited work time (Approx. 30 min. at 23 C).Therefore it is wise to
check and make sure everything is in order before starting the mixing sequence.
Stir the contents of part A with an electrical stirrer .Add part B to part A completely for 2 - 3 minutes with a low speed
stirrer until a homogenous mix is achieved. Be careful not to introduce any air bubbles while mixing until a uniform
consistency is obtained. Afterwards the mixture is left to rest for approx. 5 minutes, then pouring Magic Pox in
prepared surface.
Processing conditions:
Temperature-The optimal processing temperature is about 20 C. Raising the temperature by 10 C halves the
pot life and doubles the reactivity
Air humidity The relative air humidity during processing should not exceed 65 %.
Like all reactive resin systems the casting quantity is limited by the generated reaction heat (exothermal
reaction): often a lower curing temperature (e.g. at an ambient night temperature lower than 20 C) can counteract
too great an exothermal reaction.
Cleaning
Cleaning all tools and equipments immediately after use with acetone or cellulose thinners.
Health and Safety
Use gloves and breathing mask when applying.
Apply forced ventilation in confined spaces.
Skin splashes to be removed with hand cleanser, soap and water.
Eye splashes to be removed with plenty of water.
If ingested seek medical advice

Dear All,

We can supply EPDM scrap.

Interested parties contact us directly for a detailed price offer.

The handysand auto 2 is the latest innovative drywall sander, providing an outstanding working height of 7+ meters. Powerful 750watt motor, pressure release valve, ars technology (auto regulated suction) active on all versions and set ups

25cm*25cm*1m (boxing)

Lighter than typical north-European clothing
More autumn than winter
Includes also working dressing and special clothing
Packed into 170-200 kg capsacks

Setapol 260 1C is an elastic coated polyurethane membrane of one component for long-lasting waterproofing.It has hydrophobic resistance to sun and frost while it is breathable with anti-corrosion properties.Setapol 260 1C is ideal for the sealing of roofs , balconies ,rooms , gardens , pots and for the protection of thermal insulation foam polyurethane.
It also has coverage of 1.5 - 2.0 kg / m2 in two or three layers.

Setapol 450ML 1C is an elastic paint of aliphatic polyurethane base of a component with good mechanical strength.It has a particularly high resistance to sun and frost.There is also no yellowing on the surface.Setapol 450ML 1C is ideal as a finishing coat resistant to light alloys.

Setapol 400ML 1C is an elastic paint of aliphatic polyurethane base of a component with good mechanical strength.There is no yellowing on the surface.Setapol 400ML 1C is ideal as a final sealant on moderate pedestrian traffic surfaces.It has coverage of 0.15 - 0,25 kg / m2 in two or three layers.