Broker Of Fuel..
The recovery plant is specially designed to recover CO2 from fermentation processes at breweries. This complete CO2 plant was installed in 2001 and it has nominal CO2 removal capacity of 1000 kg/h. The plant has Siemens S 7 control system where operation is carried our via a large 12 " color screen panel with Windows CE operating system. This is a complete CO2 recovery plant and final delivery scope depends on buyers needs. The plant has been in operation only approx 5 years and is still installed and in very good condition. The carbon dioxide plants was designed by Danish Union Engineering (www.union.dk ) and the delivery includes following main components: - 1 Scrubber for gas flushing - 2 Foam catcher vessels - CO2 collection, inflammable - 2 Mehrer TZW 70 CO2 compressors - 2 Carbon filters - 2 Dehydrators - CO2 Liquefier - CO2 Storage Tank - 2 Cooling compressors GEA Grasso GD-3 for R717 - Air cooled condenser for NH2 compressors - Alarm center for CO2 and NH3 concentration - Station for 40 kg CO2 still tank filling - CO2 pumping station from a truck to the factory - CO2 purification tester - Steam heated evaporator for liquid CO2 Detailed technical information available for serious buyers
Manufacturer pompetravaini italy, made in year 2002. Vacuum pump is two staged rotating pump with externally located, grease lubricated bearings. Pump is liquid ring type designed for water sealed operation. The impeller and shaft are made of stainless steel (aisi 316), cast iron casing and manifold normal steel. The shaft is sealed with double mechanical seal. Pump is provided with connections for service water and draining. Pump includes also anticavitation valve. Pump is dismantled from its base frame but the delivery includes original electric motor eex classified abb hyr 200m lb 4 30 kw, 1476 rpm, year 1995. The equipment will be supplied loose - not as a skid. Technical data:trch 80 - 540/c2/ra Max suction pressure:25 mbar (till 300mbar) Max capacity:540 m3/h (min 400 m3/h) Flanges:80 mm Rotation speed:1500 rpm Power requirement:30 kw at 1500 rpm Year made:2002 Condition:fully operational
Rotary Lube Blower / Vacuum compressor KAESER EB 420 C û 38 m3/min, 53 kPa There are two identical sets of oil-free, 2 lobe rotary blowers, made by Germand Kaeser Kompressoren GmbH in year 2005 with accessories. Manufactures type is Kaeser ED 420 Compact Omega Pluss 53 and accessories include a control cabinet with two inverters and programmable Kaeser Start Control STC 30 unit, totally 6 preliminary intake air filters and 3 final air intake filters with their steel supports. The rotary blower units have removable sound enclose for noise insulation. Operation of the equipment was stopped in year 2007, total running hours approx 7000 and therefore they are in excellent operational condition. In addition, we can offer you service maintenance by the manufacturer at separate cost. This equipment is suitable for demanding dust collection and pneumatic transportation of various products due to oil free operation. For pneumatic transport application some changes in filters and other parts are needed. The rotary lobe has two blower shafts with high efficiency Omega profile in a blower block. The rotary lobe and the block have a very small distance and they are not touching each other's and therefore there is no need for lubrication oil. The rotors are driven by high efficiency electric motor via belt connection and they both are installed on the same base frame. . The inlet and discharge silencers are designed to be effective at all frequencies and are eminently suited to variable speed . Higher rotational blower speeds produce high volumetric efficiencies, which in turn lower discharge temperatures and power consumption. The Compact Range ensures that all serviceable items are accessed from the front panels of enclosures. The preliminary intake air filters are combination of cyclone and bag filter and it removes most of the dust from inlet air. Fine filter is a combination of cyclone and 138 ceramic fine filters which removes fine dust very effectively. Technical Data Manufacture's type: EB 420 Compact Omega plus 53 Manufactured in year: 2005 Suction capacity with max vacuum:38,0 m3/min Power demand max: 40,3 kW Rotor's rotation speed 4120 rpm Max suction vacuum: 0,53 bar (abs.) Discharge pressure: 1,0 bar (abs.) Max pressure increase: 470 mbar Temperature rise max -t: 82 K Electric motor: 45 kW û 50 Hz / 400/690V û 83/48 A Electric motor nominal speed:2965 rpm Protection class: IP 55 Inverters: Mitsubishi FR-F740-01160-EC Case ventilation fan: 370 W û 50 Hz / 230 / 400V Weight blower with the case:1120 kg Blower case main dimensions:1.8 x 1.7 x 1.8 m (K x L x S) Noise level: 99 dB (A) Noise level with the case: 84 dB (A).
Customized display and touch solutions, embedded solutions and ppe materials (face masks), technology trading, investment, business development, sourcing, supplier matching.Supply chain management in china, trading from hong kong. technology transfer
Chemicals, power products, food, automotive parts.Project consultancy
R-steel threaded lifting devices including several options as wire loops, wire loops equipped with a pressure plate and full metallic lifting devices, are designed to transport and erect precast units and elements. R-steel lifting devices have been designed and tested according to european quality standards to ensure safe precasting and lifting. - wire loops are manufactured of high-quality steel wire which are more suitable for on-site high loads such as beams. It can be equipped with a pressure plate for different lifting angles. - full metallic lifting devices equipped with pressure plate are designed for the lifting of 0 - 90 angles. The free turning swivel can also be used for turning precast elements. - all threaded lifting devices are easy to install and can be recessed if required, they can be used with all sizes of threaded inner socket anchors. - inner socket anchors are provided separately from lifting devices and it's highly recommended to use co-ordinated lifting system units for the safety of your precast site. Nailing plates, socket magnets, and plastic caps are also available. - tailor made solutions are also available.
Used industrial equipment and production lines, power generation equipment, dairy equipment, petrochemical filling lines, packing equipment, industrial processes, bewerage industry equipment.
Phone accessories and other small consumer electronics.
Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets. More information on requests, for spam protection please introduce yourself properly. Main data of one mill: Manufacture’s type: NTK 130F/LM Year of manufacture 1988 Total operating hours: approx. 75000 Rated capacity, max: 145 kW Number of blades: 3 pcs Rotor diameter: 22 m Rotor speed: 44.5 rpm Cut-in wind speed: 4.0 m/sec Cut-out wind speed: 53 m/sec (120 mph) Hub height: 26 m Generator: ASEA 145 kW / 1500 rpm / 50 Hz Blade type: LM 9.7 m H/H/T diam. 21 m Gear box type: Lohman & Stolterfort GPC 145 Clutch type: Lohr & Brokamp Universal Joint No 105 Total weight: 15200 kg.
Used computers without hdd p4/p3. Used laptops mac/p4/p3 without hdd . Used laser printers. Products are packed on eur pallets and wrapped with plastic film.
Electric motor scrap Mix of scrap electric motors from scrap yard owner. Orders from 1 container to 20 containers per month. Ex-works = 900 USD / ton (EXW) Finland. 60 km from port of Helsinki (Finland).
Certificate of quality Fineness % +-10.0 Initial setting time h:min +-0:45 Final setting time h:min +-10:00 Soundness Mum +-5.0 So3 % +-3.5 Mgo % +-5.0 Loss on ignition % +-5.0 Bending strength mpa +-6.5 Compressive strength mpa +-42.5 1ton/big bag
Common Gypsum Plasterboard Technical parameters Standards(GB/T9775-1999) Common Gypsum Plasterboard-specifications dimension(mm) depth: 9.5, 12, 15, width:1200, 1200, 1200, legnth:3000, 3000, 3000, weight(kg/m2):7.2,9.0,11.5, Simple packing specification No.s: 100,80,60, area(m2):360,288,216, weight(ton):2.67,2.69,2.61, Standard of loading No.s:76,60,50, area(m2):273.6,216,180, weight(ton):2.1,2.1.2.28
Fireproof Plasterboard technical parameters Standards(GB/T9775-1999) FireProof Gypsum Plasterboard-specifications Dimension(mm) depth: 9.5, 12, 15, width:1200, 1200, 1200, legnth:3000, 3000, 3000, weight(kg/m2):8.2,9.6,12.4, Simple packing specification No.s: 100,80,60, area(m2):360,288,216, weight(ton):3.04,2.87,2.81, Standard of loading No.s:76,60,50, area(m2):273.6,216,180, weight(ton):2.39,2.25.2.46
Waterproof Plasterboard technical parameters Standards (GB/T9775-1999) Water Proof Gypsum Plasterboard-specifications Dimension(mm) depth: 9.5, 12, 15, width:1200, 1200, 1200, legnth:3000, 3000, 3000, weight(kg/m2):8.3,9.7,12.6, Simple packing specification No.s: 100,80,60, area(m2):360,288,216, weight(ton):3.08,2.90,2.86, Standard of loading No.s:76,60,50, area(m2):273.6,216,180, weight(ton):2.42,2.27.2.50
GB Standard U profile horizontal stud Dimension(mm) depth: 0.7, 0.7, 0.7, width:100, 75, 50, Wingwidth:404040 legnth:3000, 3000, 3000, Simple packing specification weight(kg/m):0.9670.8350.698
GB standard&ISO C profile vertical stud Dimension(mm) depth: 0.7, 0.7, 0.7, width:98.5, 73.5, 48.5, Wingwidth:505050 legnth:3000, 3000, 3000, Simple packing specification weight(kg/m):1.1981.0720.934
Cement 42, 5 n/r , gypsum board, steel frame, powered gypsum, gypsum surface paper..
This Powerpak 660 horizontal thermoforming machine (form/fill/seal) is manufactured by German Tiromat Krämer+Grebe GmbH & Co in 1998. It is designed for high capacity packing of various products in food and pharmaceutical industry. This unit has been packing bread in to vacuum pack and it is equipped with a three head hot foil printer, 2- gas mixing device for CO2 injection, separate vacuum pump, cross- and longitudinal cutters and water cooled upper cover of the forming unit. Construction material is food quality stainless steel and equipment is controlled with PC-programmable Tiromat Control Unit. This unit has very little operation hours - estimated total 3000 hours - and therefore it is in excellent condition. Operating and service manuals in English, Finnish and German and machine comes with the CE-certificate. Machine type:Powerpak 660 Machine number:665/0211 Manufacturing year:1998 Foil type:Flexible Formatting width:430 mm Film type used:PS-PE 450/50 Max formatting depth:40 mm Forming dies:223-3,1 Capacity:10 phases / min Control unit:Tiromat Ho foil printer:SC-700 with 3 printing units Overall length:7.30 meters Overall width:1.15 meters Height:1.85 meters Nominal power need:50 A / 380 V / 50 Hz.
