The recovery plant is specially designed to recover CO2 from fermentation processes at breweries. This complete CO2 plant was installed in 2001 and it has nominal CO2 removal capacity of 1000 kg/h. The plant has Siemens S 7 control system where operation is carried our via a large 12 " color screen panel with Windows CE operating system. This is a complete CO2 recovery plant and final delivery scope depends on buyers needs. The plant has been in operation only approx 5 years and is still installed and in very good condition. The carbon dioxide plants was designed by Danish Union Engineering (www.union.dk ) and the delivery includes following main components: - 1 Scrubber for gas flushing - 2 Foam catcher vessels - CO2 collection, inflammable - 2 Mehrer TZW 70 CO2 compressors - 2 Carbon filters - 2 Dehydrators - CO2 Liquefier - CO2 Storage Tank - 2 Cooling compressors GEA Grasso GD-3 for R717 - Air cooled condenser for NH2 compressors - Alarm center for CO2 and NH3 concentration - Station for 40 kg CO2 still tank filling - CO2 pumping station from a truck to the factory - CO2 purification tester - Steam heated evaporator for liquid CO2 Detailed technical information available for serious buyers
Manufacturer pompetravaini italy, made in year 2002. Vacuum pump is two staged rotating pump with externally located, grease lubricated bearings. Pump is liquid ring type designed for water sealed operation. The impeller and shaft are made of stainless steel (aisi 316), cast iron casing and manifold normal steel. The shaft is sealed with double mechanical seal. Pump is provided with connections for service water and draining. Pump includes also anticavitation valve. Pump is dismantled from its base frame but the delivery includes original electric motor eex classified abb hyr 200m lb 4 30 kw, 1476 rpm, year 1995. The equipment will be supplied loose - not as a skid. Technical data:trch 80 - 540/c2/ra Max suction pressure:25 mbar (till 300mbar) Max capacity:540 m3/h (min 400 m3/h) Flanges:80 mm Rotation speed:1500 rpm Power requirement:30 kw at 1500 rpm Year made:2002 Condition:fully operational
Rotary Lube Blower / Vacuum compressor KAESER EB 420 C û 38 m3/min, 53 kPa There are two identical sets of oil-free, 2 lobe rotary blowers, made by Germand Kaeser Kompressoren GmbH in year 2005 with accessories. Manufactures type is Kaeser ED 420 Compact Omega Pluss 53 and accessories include a control cabinet with two inverters and programmable Kaeser Start Control STC 30 unit, totally 6 preliminary intake air filters and 3 final air intake filters with their steel supports. The rotary blower units have removable sound enclose for noise insulation. Operation of the equipment was stopped in year 2007, total running hours approx 7000 and therefore they are in excellent operational condition. In addition, we can offer you service maintenance by the manufacturer at separate cost. This equipment is suitable for demanding dust collection and pneumatic transportation of various products due to oil free operation. For pneumatic transport application some changes in filters and other parts are needed. The rotary lobe has two blower shafts with high efficiency Omega profile in a blower block. The rotary lobe and the block have a very small distance and they are not touching each other's and therefore there is no need for lubrication oil. The rotors are driven by high efficiency electric motor via belt connection and they both are installed on the same base frame. . The inlet and discharge silencers are designed to be effective at all frequencies and are eminently suited to variable speed . Higher rotational blower speeds produce high volumetric efficiencies, which in turn lower discharge temperatures and power consumption. The Compact Range ensures that all serviceable items are accessed from the front panels of enclosures. The preliminary intake air filters are combination of cyclone and bag filter and it removes most of the dust from inlet air. Fine filter is a combination of cyclone and 138 ceramic fine filters which removes fine dust very effectively. Technical Data Manufacture's type: EB 420 Compact Omega plus 53 Manufactured in year: 2005 Suction capacity with max vacuum:38,0 m3/min Power demand max: 40,3 kW Rotor's rotation speed 4120 rpm Max suction vacuum: 0,53 bar (abs.) Discharge pressure: 1,0 bar (abs.) Max pressure increase: 470 mbar Temperature rise max -t: 82 K Electric motor: 45 kW û 50 Hz / 400/690V û 83/48 A Electric motor nominal speed:2965 rpm Protection class: IP 55 Inverters: Mitsubishi FR-F740-01160-EC Case ventilation fan: 370 W û 50 Hz / 230 / 400V Weight blower with the case:1120 kg Blower case main dimensions:1.8 x 1.7 x 1.8 m (K x L x S) Noise level: 99 dB (A) Noise level with the case: 84 dB (A).
Airlaid paper rolls, paper serviettes, tissue paper rolls, spunlace non woven fabric, pe coated paper board, paper board.
Used industrial equipment and production lines, power generation equipment, dairy equipment, petrochemical filling lines, packing equipment, industrial processes, bewerage industry equipment.
Belt filter press.
The equipment is designed and manufactured by Gough & Co Ldt, UK in year 1999 / installed in 2000, manufacturer’s type single deck Vibracon GVF4. We have totally 3 identical units which were dismantled in 2007 and all of them are in very good operational condition. These are single deck circular screen design for high velocity scalping, de-watering or single deck separation in chemical and pharmaceutical industry. (These units were screening oversized particles in PVC - granulate factory truck loading station) The perforated screen and all product touching parts are made on stainless steel AISI 304L. Top deck houses the screen and the discharge spout for oversize particle removal is fitted to it. Top deck is supported with mechanical spring and vibration movement is created by two contra rotating vibrating motors on the outside of the unit so there are no internal working parts. Vibration power can be adjusted. Technical data: Type: Vibracon GVF 4 Material: AISI 304L – product touching parts Perforated screen: Mesh size 4 mm Screen diameter: 1100 mm Screen area: 9500 cm2 Vibrators: 2 x 0.52 kW units.
The vacuum evaporator is made by Italian Ecoteck in year 2003 and operation was stopped in early 2009 and it is in very good operational condition. This unit is made for concentrate acidic liquid wastes and therefore all liquid touching parts are made of acid proof steel ( SS 2353) or PVC. The evaporation capacity of the unit is 5000 liters / day. The unit is a complete working unit and it includes evaporator, boiler, heat pump, centrifugal pump, water-air cooler, steam ejector, control unit and all other necessary equipment to complete the unit. Operation principle: Steam rises from the boiler through a drop dispenser to the cooling unit where it condensates. The condensate drops with the gravity down to vacuum system. In-build heat pump heats up the cooling media and simultaneously cools down the condensate. Water – air cooler cools down the extra heat from the process. Necessary vacuum is generated with a centrifugal pump and a steam ejector. Condensate rejection takes place in accordance with prescheduled frequency. Technical data: Manufacturer: ECOTECH Srl Italy / Vilokan Ren Miljöteknik Sweden Type: ECO 5000 VS-HP, R407C Year made: 2003 Evaporation capacity: 5000 liters / 24 hour (pure water) Electricity consump.: about 0,15 kWh / liter pure wateri) Control unit: Siemens Micromaster 420 Compressor: Bitzer Kuhlmachinenbau GmbH, Compressor type: 6G-40,2 Compressor capacity: 126.8 m3/h, 19/28 bar Refrigenerant: R 407 C Main dimensions: 2.8 m x 1.3 m x 2.9 m Weight: 1500 kg.
ELMO-G Blower - Vacuum pump 1000 m3/h The blowers are made by German ELMO Vacuum Technology GmbH, a Siemens company in year 2002 and they are single stage, gas ring type. The vacuum pumps are in good operational condition. We have three identical pump units and originally the pumps were in dust suction operation and therefore the delivery includes 3 pcs high efficiency cyclone type dust filter with electric discharge vibrators. Motor speed is controlled with individual inverters. Units can be sold separately. ELMO-G vacuum pumps can be used for suction operation or as compressors in pneumatic transportation system. They have side-channel principle using gas ring as a sealing and the gas flows through the compressor along a helical trajectory and is repeatedly accelerated and thereby repeatedly compressed according to the required operating point. The blowers are oil-free and thus suitable for various applications. The blowersÆ have both suction and discharge noise silencer. For pump curves, both in suction and compression, as well as additional information please contact us. Technical Data: Manufacturer's type:ELMO 2BH1943-1GC36 Year of manufacture:2002 Suction capacity with max vacuum:16,7 m3/min (50Hz) Suction capacity with max discharge pressure:21,5 m3/min (50Hz) Max pressure difference in vacuum operation:0,30 bar (50 Hz) Max pressure difference in compression operation:0,35 bar (50 Hz) Inverter:Danfors VTL 6000 HVAC Blower's rotation speed2920 rpm / 50 Hz and 3520 rpm / 60 Hz Electric motor (Siemens):50 Hz: 21.0 kW û 300/690V û 39.5 / 23.0 A 60 Hz: 24.2 kW û 460 V û 41.0 A Protection class:IP 54.
The fan is made by German Pollrich Ventilatoren GmbH in year 2004 and it has been as a back-up emergency fan which has practically newer used and therefore the unit is new like condition. This fan was designed to blow explosive air/gas mixture (VOC) and therefore it fulfills category II 2G, temperature class 1 ATEX 95 norm of explosive proof design. The motor and fan are built on a common heavy duty frame and they are connected with a flexible coupling. Technical data: Manufacturer: Pollrich Ventilatoren GmbH Year of manufacture: 2004 Fan type: VR50S11C1UK0900LG360MMUU Manufacturing no: 123665 Volume: 10.55 m3/sec (37980 m3/h) Max press difference: 8000 Pa (0.08 Bar) Speed: 2980 RPM Max gas temperature: 80 C Power requirement: 104.6 kW Electric motor: CEMP 132 kW / 2970 RPM Type: AC70 315M 2 Classifications: II 2 G EEXd IIC T4 IP 55.
40-500 gsm 100-200 cms
Sheet metal working machinery.
The main description of the plant equipmet is: 1. Brew House Make & Capacity: Steinecker1995 -1999 5 brews/d, 450-500 hl/brew. for 7000 kg malt, 3850 Raw grain Cast-out quantity: 500 hl, 16,5° Plato 8 Brews/ 24 hours, annual capacity 0.85 Mhl Controls are based on Siemens S5 and S7 PCS with, Botec Control system, PC Windows 2000 (Steinecker) Laboratory yield = 97.1% (2.1.09 – 28.5.09, 837 brews) The Brewhouse was installed in 1996 - 1999 by Steinecker to a high standard of control and automation and it contains the following main equipment: Wet Conditioning Mill, capacity 20 tons/hour and it is fully overhauled 2008 Configuration, main characteristics: 1 wet mill plant: 20 t/h 1 mash tun kettle plant: V=550 hl 1 lauter tun plant: D=7200mm 1 weak wort tank: V=155 hl 1 pre run vessel: V=640 hl 1 CIP- water distributor brew/whirpool kettle hot wort max. 520 hl (1 brew / 5 hours) wort cooling 400 hl/h, 10°C - Mash Kettle, a jacketed vessel 550 hl - Enzyme Dosing pot and pump - Lauter Tun complete with spent grain tank and Pondorff pneumatic grains transfer. Tun capacity 814 Hl and diameter 7200 mm, Solids capacity of 7000 kg malt and 3850 kg raw grain. Complete with internal rakes and scrapers - Pre Run Vessel complete with internal heater , volume 640 hl - Wort Boiler/ Whirlpool, gross volume 757 hl net 520 hl - Wort Cooler with aeration – GEA supplied plate heat exchanger (YOM 1990) – rated at 450 Hl/hr cooling the wort from 95oC down to less than 10oC. Cooling achieved with brewing water and then chilled water. Aeration achieved by use of a sintered disc and static mixers, and controlled manually using mass flow meters - 2 Hop Pellet Tanks - 2 Hop Oil Tanks - Brewhouse Weak Wort Tank, volume 150 hl - Alfa-Laval Decanter, year 2008, capacity 100 hl / h - 2 Weak Wort Tanks, volume approx 80 hl each - Gypsum Tank, volume approx 40 hl - Wet starch tank – volume 100 hl - Spent Grains Silo - Spent Grains Drying System - Bulk Acid tank – plastic tank with integral bund and dosing pumps
Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets. More information on requests, for spam protection please introduce yourself properly. Main data of one mill: Manufacture’s type: NTK 130F/LM Year of manufacture 1988 Total operating hours: approx. 75000 Rated capacity, max: 145 kW Number of blades: 3 pcs Rotor diameter: 22 m Rotor speed: 44.5 rpm Cut-in wind speed: 4.0 m/sec Cut-out wind speed: 53 m/sec (120 mph) Hub height: 26 m Generator: ASEA 145 kW / 1500 rpm / 50 Hz Blade type: LM 9.7 m H/H/T diam. 21 m Gear box type: Lohman & Stolterfort GPC 145 Clutch type: Lohr & Brokamp Universal Joint No 105 Total weight: 15200 kg.
Very little operated (ony 6000 hours totally!) fuel oil fired package boiler made by Högfors (nowadays Foster Wheeler) in 1988. Complete plant with combustion air fan and feed water pumps for immediate delivery, in very good condition. Main scope of the delivery: - Högfors 30 t/h boiler - Oilon burner - Economizer - Combustion air fan - 2 pcs of 90 kW / 25 bar KSB feed water pumps - Fuel oil pumping unit made by Oilon - 8 pcs of steam shoot blowers - valves, fittings and maintenance supports . Type of boiler Water tube type with natural circulation, with two drums Manufacturer Kymin Osakeyhtiö, Högfors, Finland (Foster Wheeler) Model of the boiler: H52-47-25 bar Year of manufacturing 1980 Starting day of operation 16.11.1980 Evaporation 47 t/h saturated steam Temperature of steam 226 oC Effect 30 MW Structural pressure 25 bar Feed water temperature 120 oC Furnace volume 74,5 m3 Surface of furnace c. 136 m2 Surface of convection part 420 m2 Surface of economizer c. 504 m2 Water volume 15,8 m3 Oil Heavy oil (POR 230) Oil burner Saacke SKV, fully automatic, modulating Regulating area of burner 610-3050 kg/h Oil pumping- and pre- Oilon Osva 4000 kg/h heating station Feed water pumps 2 pcs + 1 pc as spare. KSB-centrifugal pump MOVI 65/6, massflow 59 t/h, 29,5 bar motor 90 kW, 2900 r/min Primary air fan Mercantile KDER 75, 37300 Nm3/h, motor 115 kW, 1500 r/min Sootblowers Diamond Superior sootblowers 4 pcs in boiler part Diamond Superior sootblowers 4 pcs in economizer. Dimensions of boiler part: Height 5,2 m, Width c. 4,5 m, Length 10,0 m Weight of boiler part c. 54 t. without water and accessories Weight of economizer c. 15 t. without water and accessories Boiler is suitable for gas operation by changing the burner. The boiler has been in operation only about 6.000 hours. Equipment for SaleGeneral Industry Textile Machinery Process Equipment Energy & Power Gas & HFO Boilers Wind Turbines.
Frankincense and myrrh .Export
