Double Part Thimble Eye Double Part Basket Grommet Round Application for Grommat Grommat slings can be fabricated in very short circumstances. The reason is this: Grommat slings are made from one continuous length of strand or wire rope. This requires only one tuck-in point as compared with six tuck-in points needed manufacturer an endless sling. A Grommat consists of an endless rope having construction 6/1 construction & is used where high ultimate breaking strength of the rope is required beyond the limits of a single part rope. A strand of sufficient length to complete the Grommat shall be obtained by either of the following methods: Method A: An order strand shall be unlaid from a specimen of 6/1 rope conforming to the requirement of the customer. Method B: Unlaying from a specimen of 6/4 rope having strands in all respects equipment to those obtained by method A above. Method C: Using a virgin strand either prefromed or post formed & in all other respects equivalent to those obtained by method A & B. During the course of construction of a Grommat the performed lay of the strand shall be maintained and shall not be interfered with except when laying in the core for which purpose length of strand left to form the core should be straightened . The length of the strand required to form a Grommat shall be equal to about 7.5 times the parameter of the Grommat in case of spliced Grommat. But in case of complete streamline splicing length shall be 4 times the effective length. Butt Splice The two ends of the rope should be joined together by two five –tuck splices. Number of Tucks The splices shall be tucked three times the full size of strand, a fourth time with the strand each reduced to half the original number and a fifth with the strands each further reduced to one third the original number. The heart strand is to be rowed in during tucking so that a double heart is produced for at least the length of the first three tucks in both directions. Method of Tucking The Tucks of the Splice shall be made over one strand and under one strand against the lay of the rope. The heart strand of the rope shall not be removed when the strands are opened out for tucking, but may be cut to a suitable length. Finishing The ends of the splice in way of the twisted off ends of wire that is between the end and the third tuck shall be tightly served with seizing wire, after parcelling with canvas, Hessian or wax paper.
Two leg wire rope sling with main ring at top and hooks at the bottom. Three leg wire rope sling with main ring at top and thimble at the bottom. Four leg wire rope sling with main ring and intermediate ring at top with bow shackle at bottom. Four leg sling with main ring with thimble at top and plain loops at bottom. Braided / Plaited belt lifting slings - Available in standard lts. of 10m &10 in capacities ranging from 10 to 40 tons with steel core ropes.
Flattening Test - Ferrules shall be pressed, along the major axis until the inner, surfecestmeet. Multipurpose, Portable, Universal, Gearless, Hand, operated Pulling and Lifting machine, Supplied, complete with telescopic, operating handle and, standard Length of super flex steel fibre-mixed core, wire-rope fitted with Hook or Shackle at one end and, fused and tapered at the other end. After completion of the test, there shall, be no visible crack on the ferrule. Type, Normal Size, Length before Pressing Min., Length after pressing Min, Thickness Min T, Suitable for Normal Wire Rope Size, Lower Limit, Upper Limit, (1), (2), (3), (4), (5), (6), (7), Type A , 3, 11, 17, 1.61, 2.00, 3.15, 4.0, 10, 22, 1.7, 4.40, 4.75, 6, 10, 23, 2.1, 5.85, 6.30, 8, 27, 34, 3.0, 7.85, 8.40, 9, 30, 33, 3.50, 8.80, 9.45, 10, 32, 35, 3.75, 9.80, 10.50, 11, 36, 43, 5.25, 10.75, 11.55, Type B, 10, 45, 53, 4.2, 11.75, 12.65, 15, 46, 50, 3.8, 13.76, 15.75, 17, 50, 60, 5.2, 15.76, 17.85, 19, 56, 62, 5.00, 17.86, 19.99, 21, 62, 70, 6.20, 20.00, 21.99, 23, 78, 86, 7.55, 22.00, 23.89, 25, 83, 94, 8.00, 24.00, 25.99, 27, 92, 108, 8.85, 26.00, 27.99, 29, 98, 114, 9.85, 28.00, 29.00, 31, 101, 115, 10.00, 30.00, 31.99, 33, 105, 118, 11.07, 32.00, 33.99
Nominal size of rope A, C, D, F, G, K, R1, R (1), (2), (3), (4), (5), (6), (7), (8), (9), 08, 33, 11, 46, 9, 4, 3.5, 25, 12, 10, 44, 15, 56, 11, 6, 5.5, 32, 16, 12, 60, 20, 82, 13, 8, 7.5, 44, 22, 14, 60, 21, 82, 15, 8, 7.5, 44, 22, 16, 70, 23, 94, 17, 10, 29.5, 50, 25, 18, 80, 26, 104, 19, 12, 11.0, 56, 28, 20, 88, 28, 116, 21, 12, 11.0, 64, 32, 22, 100, 30, 125, 24, 14, 13.0, 72, 34, 24, 104, 33, 140, 26, 14, 13.0, 76, 38, 25, 114, 36, 150, 27, 16, 14.5, 82, 42, 29, 124, 39, 165, 31, 18, 16.5, 88, 44, 32, 140, 45, 190, 34, 20, 18.5, 100, 50, 35, 154, 50, 208, 38, 20, 18.5, 114, 56, 38, 169, 56, 234, 41, 22, 20.5, 125, 64, 41, 169, 56, 234, 44, 22, 20.5, 125, 64, 44, 190, 65, 260, 47, 25, 22.5, 140, 68, 48, 206, 67, 275, 51, 28, 25.5, 150, 75, 51, 229, 72, 300, 55, 32, 29.5, 165, 78, 54, 229, 76, 300, 58, 32, 29.5, 165, 78, 57, 243, 78, 330, 61, 34, 31.5, 115, 88, 64, 276, 88, 375, 69, 38, 35.5, 200, 100, All dimensions in millimetres., Note, For wire ropes of intermediate sizes, the next larger size of thimble shall be used., Dimension M is the standard pin hole and the largest pin-hole for each thimble. Should a, smaller pin-hole be required the diameter of this shall be stated in the enquiry and order.
Features Basket is cast steel. Wedge socket terminations have an efficiency rating of 80% based on the catalog strength of XXIP wire rope. Wedges are color coded for easy identification. Blue - largest wire line size for socket. Black - mid size wire line for socket. 7/16" on US4 9/16" on US5 Orange - smallest wire line size for socket. Cast into each wedge is the model number of the socket and the wire line size for which the wedge is to be used. Cast into each socket is the name "McKissick", "Crosby" or "CG", its model number and its wire line range. By simply changing out the wedge, each socket can be utilized for various wire line sizes (Ensure correct wedge is used for wire rope size). Load pin is forged and headed on one end. US-422 wedge sockets contain a hammer pad (lip) to assist in proper securement of termination. Crosby products meet or exceed all the requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B20.26. UWO-422 Wedges are to be used only with the US-422 Wedge Socket Assemblies.
Close Spelter Sockets All Dimensions in mm.
Factor Of Safety 5:1 Tensile Strength: 1770/1960 N/mm2 Note The capacity indicated in the above table, for basket hitch and choker itch is for guidance only, vertical column is the actual load the slings can be tested and certified in other words safe working load is applicable for vertical lift only.
Nominal Size of Rope A, B, C, D, E, F, G, H, J, K, L, (1), (2), (3), (4), (5), (6), (7), (8), (9), (10), (11), (12), 08, 22, 38, 13, 34, 54, 09, 04, 3.5, 62, 04, 30, 10, 24, 46, 15, 38, 64, 11, 06, 5.5, 76, 05, 34, 12, 32, 60, 19, 44, 80, 13, 08, 7.5, 90, 06, 44, 14, 32, 60, 21, 44, 80, 15, 08, 7.5, 90, 06, 44, 16, 40, 72, 23, 58, 98, 17, 08, 7.5, 114, 08, 56, 18, 44, 80, 29, 66, 110, 19, 10, 9.5, 125, 08, 60, 20, 50, 94, 31, 74, 124, 21, 12, 11.0, 150, 10, 70, 22, 58, 102, 34, 82, 134, 24, 121, 11.0, 165, 10, 78, 24, 64, 108, 36, 92, 150, 26, 12, 11.0, 176, 10, 84, 25, 70, 118, 37, 108, 162, 27, 14, 13.0, 200, 10, 90, 29, 76, 132, 41, 112, 176, 31, 16, 14.5, 230, 12, 100, 32, 96, 152, 44, 134, 196, 34, 16, 14.5, 250, 12, 120, 35, 104, 174, 48, 152, 228, 38, 19, 17.5, 300, 16, 136, 38, 114, 198, 54, 165, 254, 41, 24, 22.0, 330, 18, 150, 41, 114, 198, 56, 165, 254, 44, 24, 22.0, 330, 18, 150, 44, 125, 222, 57, 178, 285, 47, 26, 23.5, 355, 25, 175, 48, 134, 246, 67, 190, 315, 51, 28, 25.5, 380, 28, 190, 51, 140, 256, 70, 330, 330, 55, 30, 27.5, 400, 28, 196, 54, 140, 256, 70, 200, 330, 58, 30, 27.5, 400, 28, 196, 57, 146, 270, 76, 216, 355, 61, 32, 29.5, 425, 30, 206, 64, 156, 308, 95, 240, 400, 69, 44, 41.0, 450, 32, 220, 70, 200, 400, 120, 275, 500, 75, 60, 57.0, 480, 40, 280, Note, For wire ripes of intermediate size, the next larger size of thimble shall be used., These dimension are minimum for thimblas of nominal size up to and including 41 only
Crosby Fittings Oblong Master Link Item No. W.L.L (tones) Dimensions (mm) N.W IL IW D 8-003-06 1.5 100 60 11 0.2 8-003-0806 3.2 120 70 14 0.4 8-003-1008 4.0 140 80 17 0.7 8-003-13 6.3 160 90 19 1.0 8-003-1310 8.0 160 22 22 1.5 8-003-16 11.5 190 25 25 2.2 8-003-1613 15.0 180 105 28 2.7 8-003-19 17.0 200 120 30 3.5 8-003-2216 20.0 240 140 34 5.1 8-003-26 25.0 250 150 38 7.0 8-003-2619 30.0 250 150 40 8.0
Open Spelter Sockets All Dimensions in mm.
Marzoli Ring High quality spare parts for Marzoli machines manufacture, importers and suppliers in India. We use the most advanced technology and graded raw materials to manufacture the Textile Machinery Marzoli Spare Parts like Marzoli Rings, Peg etc. We have been regularly supplying this "Marzoli Spare Parts" to many contractors and associated people in this Field across India. We would request to you to please send to us your enquiries for the same so that we can send to you more details and our commercial offer for the same.
Name - Full Thread Stud Min order - 10 pcs Manufacture in Ahmedabad Gujarat India Packing as per client require Sample yes Capacity 500000 pcs per month Sample Cost Buyer Brand-Accurate Hs code - 7318 Key Specification- 1.Grade 4.6,4.8,8.8,10.9,12.9 (Is,ISO & Din) & B7,B7m,B16,l7,B8,B8m (Cl2) 2.Material as per is i 367 part-iii & astm 193,astm A320 a307 A453 3.Size m6 to m100 & above (1/4'' to 4.0'' & above) Key advantage 1.Highly accurate in dimension and supply with certificate
We are offering anchor fastener
Steel Clipper Belt Fasteners Products Description : Fastener Steel Clipper, Wire Hook Conveyor Belt Fastener --All the Belt Clipper Import from American Clipper and Lacer Feature: 1.Top quality of clipper grade 2.Ensure the enough tensile 3.Resistance abrasion and tear 4.Good running ability
1.Product Name: BA20D ring 2.Product Type: Philips BA20D ring 3.Material: SUS 430 4.Usage: PhilipsMotorcycle lamp base 5.Product Dimension: Height:11.5-0.5mm Diameter: 18.8+0.1mm Thickness: 0.2mm 6.Product Feature: Outgassing Test: passed; 7.Packaging Details: 5000 pcs per carton. FAQ: 1.How do you clean the BA20D ring after stamping? We have automatic production line equipped with ultrasonic cleaning machine. 2.Do you have other ring type? Yes, we have another type which is higher. 3.Whatâ?? your MOQ? 100K. About Us: Invitech is a professional manufacturer of precision metal and plastic components. Our core technology team specializes in precision progressive die stamping, compression molding for more than 30 years. As a result, we have the capability to provide metal stamping services and products for a wide variety of industries. We have advanced management system and strict work style ,it can bring a strong guarantee to providing customers with high-quality and high value-added products. Enthusiasm, honesty, win-won are footstone to cooperate with our customers.
1011.00 AISI 304 - STAINLESS STEEL WITHOUT LID SIZE: 125X330 mm EXWORKS PRICE: USD 20.00 2011.00 SAE 1020 - GALVANIZED CARBON WITHOUT LID SIZE: 125X330 mm EXWORKS PRICE: 13.00
1009.00 AISI 304 - STAINLESS STEEL WITHOUT LID SIZE: 100X280 mm EXWORKS PRICE: USD 15.00 2009.00 SAE 1020 - GALVANIZED CARBON WITHOU LID SIZE: 100X280 mm EXWORKS PRICE: USD 10.00
1003.00 AISI 304 - STAINLESS STEEL WITHOUT LID SIZE: 100X250 mm EXWORKS PRICE: USD 13.00 2003.00 SAE 1020 - GALVANIZED CARBON WITHOUT LID SIZE: 100X250 mm EXWORKS PRICE: USD 10.00
1004.00 AISI 304 - STAINLESS STEEL WITH LID SIZE: 100X250 mm EXWORKS PRICE: USD 15.00 2004.00 SAE 1020 - GALVANIZED CARBON WITH LID SIZE: 100X250 mm EXWORKS PRICE: USD 11.00
1006.00 AISI 304 - STAINLESS STEEL WITH LID SIZE: 140X310 mm EXWORKS PRICE: USD 24.00 2006.00 SAE 1020 - GALVANIZED CARBON WITH LID SIZE: 140X310 mm EXWORKS PRICE: USD 17.00
