Wq-cond rugged water conductivity sensors description Wq-cond conductivity sensors are suitable for measuring conductivity in a wide variety of applications including laboratories, streams, rivers, and groundwater. The conductivity sensor's small size and rugged housing make it useful for hand held measurements or permanent installation. Wq-cond rugged water conductivity sensors features * fully encapsulated electronics * dual 4-20 ma outputs * sensor armor available for harsh environments * marine grade cable with strain relief * measure conductivity up to 82 feet deep Wq-cond conductivity sensors applications Ideal for stream and lake monitoring, aquaculture studies, baseline analyses, mitigation monitoring, and other environmental applications. Wq-cond rugged water conductivity sensors specifications * temperature range: 23 to 158'f (-5 to 70'c) * conductivity accuracy: +0.5% of reading * temperature accuracy: +0.4'f (+0.2'c) * temperature resolution: 0.02'f (0.01'c) * output: dual 4-20 ma * maximum pressure: 35 psi (82 ft (25m)) * warm-up time: 3 seconds minimum * operating voltage: 10-36 vdc
Fsm-10h-01 pre-calibrated module for lpg gas Fsm-10h-01 is pre-calibrated module for lpg gas alarm which applies tgs2610-d00 sensor together, it features durability and stability. The module outputs pwm signal which is proportional to lpg gas concentration (the module has a memory which is stored with factory calibration data), also is capable of detecting sensor wire breakage and short. The module can operate at wide temperature from -10~70'c. Furthermore, the unit is less sensitivity to vocs gas, it immunes poison by silicon compounds, it suits to work at rugged environment. Fsm-10h-01 combustible gas sensor module features * pwm, usart digital output proportional to gas concentration * maintain free * compact size, low cost * meets rohs requirement Fsm-10h-01 combustible gas sensor module applications * detect flammable gas leakage * flammable gas leakage detector * industrial detector Fsm-10h-01 combustible gas sensor module specification * gas sensor: tgs2610-d00(semiconductor) * detection range: 0 ~ 4, 000ppm h2 * error: â± 300ppm * response time (t90): â?¤30s * operation temperature: -10'c ~+70'c * operation humidity: 20~95%rh(no condensing) * input voltage (vin): 5.0â±0.2v dc * power consumption: â?¤1.5w
PSC-SSS (Smart Small Sensor) Precise non-contact temperature measurement from -50'C to 975'C PSC-SSS-LT Infrared Temperature Sensor Description The PSC-SSS IR temperature sensor series is a highly versatile low cost solution for reliable temperature measurement. It features a temperature range of -50 to 1800'C which is fully scalable by an operator via programming keys, or by use of the included, no cost PSC Connect software. Other IR sensor parameter adjustments include peak picking, valley hold, average, and extended hold function with threshold and hysteresis. The sensor head can be installed in higher ambient temperature, and a full line of rugged industrial accessories is available for its protection and optimum operation. Its small size facilitates temperature measurement in not easily accessible areas and simplifies integration into existing manufacturing systems. All PSC-SSS Sensors feature a choice of outputs including 4 to 20 mA, thermocouple, and linear voltage. Optional digital outputs include USB, RS-232, RS-485, CAN, Profibus DP and Ethernet. Programmable functional inputs for external emissivity adjustment, ambient temperature compensation and trigger reset of hold functions are provided. PSC-SSS-LT Infrared Temperature Sensor Features * One of the smallest infrared sensors worldwide with 22:1 optical resolution * Rugged and usable up to 180'C ambient temperature without cooling * Separate electronics with easy accessible programming keys and LCD backlit display * Selectable analog output: 0/4-20 mA, 0-5 V, 0-10 V, thermocouple type K or J * Optional USB, RS485, RS232 interface, relay outputs (2 x optically isolated), CAN-Bus, Profibus DP, Ethernet * Installation of up to 32 sensing heads PSC-SSS-LT Infrared Temperature Sensor Specifications * Temperature Range: -50 to 975'C * Spectral Response: 8 - 14µm * Optics Type: Laser Accessory * Min. Spot Size: 1.2 mm * Response Time: 150 ms * Power Supply: 8-36 V DC * Environmental rating: IP 65 (NEMA-4) * Relative humidity: 10 - 95%, non condensing
Mb1043 hrlv-maxsonar-ez4 High performance ultrasonic rangefinder Mb1043 hrlv-maxsonar-ez4 ultrasonic rangefinder product description The hrlv-maxsonar-ez4 is the narrowest beam width sensor that is also the least sensitive to side objects offered in the hrlv-maxsonar-ez sensor line. The hrlv-maxsonar-ez4 is an excellent choice when only larger objects need to be detected. Mb1043 hrlv-maxsonar-ez4 ultrasonic rangefinder product specifications * resolution of 1mm * 10hz reading rate * 42khz ultrasonic sensor measures distance to objects * rohs compliant * maximum range of 5000 mm (195 inches) * operates from 2.5v-5.5v * low 3.1ma average current requirement * operational temperature from -0'c to +65'c Mb1043 hrlv-maxsonar-ez4 ultrasonic rangefinder features and benefits * best noise tolerance of the hrlv-maxsonar-ez sensors * most noise tolerant acoustic sensitivity * ignores some small targets and medium targets * detects most large targets to long distances * narrow beam width Mb1043 hrlv-maxsonar-ez4 ultrasonic rangefinder applications and uses * large target detectio
Fs1015cl gas flow sensors description Fs1015cl mass flow sensors are specially designed for medical equipment flow monitor and control applications, and are made with world leading proprietary mems mass flow designed channel with a low pressure loss. The current models can be readily applied to ventilators and anesthesia equipments. These sensors can also be sterilized in medical liquids for reuse or hygienic purposes. Fs1015 series can measure a flow up to 150 slpm. Iso-15mm connection model is readily applicable to ventilators and/or anesthesia equipments. Fs1015cl gas flow sensors features and applications - mems thermal mass flow sensor - excellent rangeability with integrated multiple sensing elements - high stability at null and full scale - fast response - low power consumption - low pressure loss Fs1015cl gas flow sensors performance specifications * flow range: 0 to 100; 0 to 150slpm * turn-down ratio: > 100 : 1 * accuracy: +/- (2.0 + 0.5 fs) % * repeatability: +/- 0.5% reading * null shift: â± 30mv * output shift: +/- 0.12%/'c * response time: 8 (max.) ms
WQ730 Turbidity Sensor Description WQ730 Turbidity Sensor is a highly accurate submersible instrument for in-situ environmental or process monitoring. Applications for the WQ730 include: water quality testing and management, river monitoring, stream measurement, reservoir water quality testing, groundwater testing, water and wastewater treatment, and effluent and industrial control. WQ730 Submersible Water Quality Sensor Turbidity Sensor Features * 4-20 mA output * Marine grade cable with strain relief * In-situ turbidity measurement * Simple and convenient to use * Rugged stainless steel and Delrin sensor housing WQ730 Turbidity Sensor Specifications * Range: 0-50 NTU and 0-1000 NTU * Accuracy: +/- 1% of full scale * Meter Resolution: 12 bit * Output: 4-20mA * Operating Voltage: 10-36 VDC at 40 MS * Current Draw: 30 mA plus sensor output * Warm Up Time: 5 seconds minimum * Operating Temperature: 14 to 122'F (-10 to +50'C) * Maximum Pressure: 30 psi
Mfm2040u digital gas flow sensor description Mfm2000 series is a gas flow sensor with low pressure drop capable of measuring medical gases up to 45 lpm. It is configured to be customizable with different flow inlet and outlet configurations. Mfm2040u digital gas flow sensor features * flow range: 0.04 to 40 slm * operating temperature range: -40 to 85'c * resolution: 15bit * sampling time: 7.5ms * low pressure drop flow sensor * high accuracy +/-2.5% reading * calibrated and temperature compensated for air * low power consumption * digital i2c * made for medical applications * calibrated for air, and o2
Wq-fdo optical dissolved oxygen sensor description The wq-fdo optical dissolved oxygen transmitter is an instrument designed for measuring dissolved oxygen concentrations in liquids. The wq-fdo optical dissolved oxygen transmitters were developed to meet different requirements ranging from surface water monitoring programs to harsh waste water applications. The optical dissolved oxygen transmitter has been specifically designed to meet the demanding requirements of the environmental monitoring and scientific research sectors, providing long term, accurate and reliable dissolved oxygen measurement. The wq-fdo optical dissolved oxygen transmitter has extremely low power requirements and a 4-20 ma output making it ideal for incorporation into remote environmental monitoring installations. Wq-fdo optical dissolved oxygen sensor features * extremely fast and precise optical do sensor - outstanding for field and lab applications * proven green light technology for long operation life of sensor * beveled membrane repells interference that can be caused by air bubbles * universal protective armoring available * low power consumption and low maintenance * simple to integrate and operate * one year sensor life Wq-fdo optical dissolved oxygen sensor applications Long and short term monitoring for streams, rivers, lakes, aquaculture, thermocline profiling, industrial outfalls, wastewater, scientific research, homeland security, the food and wine industry, and more. Wq-fdo optical dissolved oxygen sensor specifications * dissolved oxygen accuracy: +/- 0.5 % of value * dissolved oxygen repeatability: 0.01 ppm, * temperature, accuracy: +/-0.2'f (+/-0.1'c), * temperature, resolution:, 0.02'f (0.01'c), * temperature, range: 32 to 122'f (0 to 50'c, * max pressure: 35 psi (25m/82ft water depth), * operating voltage: 10-30 vdc, * warm up time: 6 sec. Min, 8 recommended,
Dgs-so2 968-038 digital so2 sensor module description Easily add so2 sensing to your iot application with our sulfur dioxide digital gas sensor module that provides a calibrated and temperature compensated output. 0 to 20 ppm so2 sensor with digital output. Dgs-so2 968-038 digital so2 sensor module benefits Low power - 1 mw 1 minute sampling Calibrated & temp. Compensated output Fast response < 30 seconds Simple digital uart interface Integrated t & rh sensors Robust 10-year estimated lifetime Rohs compliant Small form factor Uart to usb adapter provided Lightweight (< 2 oz.) Dgs-so2 968-038 digital so2 sensor module applications Air purification control Air quality monitoring Industrial safety sensing Dgs-so2 968-038 digital so2 sensor module measurement performance characteristics Based on standard conditions 25 âºc, 50% rh and 1 atm Measurement range: 0 to 20 ppm Resolution: 50 ppb Measurement accuracy: 15% of reading, , measurement repeatability, : < â± 3% of reading, T90 response time (100 ppm step), : < 30 seconds,
Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module description Quickly integrate hydrogen sulfide sensing into your system with very low power consumption and a simple analog sensor signal output. The ulpsm converts the hydrogen sulfide sensors linear current signal output to a linear voltage signal, while maintaining the sensor at its ideal biased operation settings. Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module benefits 0 to 3 v analog signal output Low power consumption < 45 uw Fast response On-board temperature sensor Easy sensor replacement Standard 8-pin connector Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module applications Fixed industrial safety monitoring Portable industrial safety monitoring Portable personal safety monitor Indoor air quality monitoring Outdoor air quality monitoring Bad breath/halitosis sensing Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module performance characteristics Measurement range: 0 to 50 ppm Lower detection limit: 0.3 ppm Resolution: 0.15 ppm Accuracy: < â± 2 % of reading Response time t90: < 30 seconds Power-on stabilization time: 60 minutes recommended
4nd citicel nitrogen dioxide sensor key features & benefits , industry leading reliability , improved performance variability 4nd citicel nitrogen dioxide sensor application Industrial safety: sensors for portable gas detectors used in industrial hygiene and confined space entry. 4nd citicel nitrogen dioxide sensor performance characteristics , nominal range: 0-20 ppm , expected operating life: two years in air , output signal: 0.6 , ± 0.15 ua/ppm , resolution: 0.1 ppm , repeatability:
Nh3-3e100se ammonia sensor nh3 sensor description Nh3-3e100se ammonia sensor, 3 electrode sensor; available in mini, classic, 4-series and 7-series formats. Nh3-3e100se ammonia sensor nh3 sensor features Amperometric 3 electrode sensor cell Very stable zero reading Very selective Highly sensitive Hydrous electrolyte Nh3-3e100se ammonia sensor nh3 sensor typical applications Tlv-monitoring, leakage detection Portable & fixed point applications Food & refrigeration industry, general industry, semiconductor industry Nh3-3e100se ammonia sensor nh3 sensor technical specifications Measuring range: 0-100 ppm Sensitivity range: 130 na/ppm â± 30 na/ppm Resolution at 20â°c: < 1 ppm Linearity: < 10% full scale Operation temperature range: -20â°c to +40â°c Operation humidity range, : 15-90% r.H, non-condensing
Sg01l-5lens Concentrator lens sic based uv photodiode avirtual = 55 mm2 Properties of the sg01l-5lens uv photodiode Broadband uva+uvb+uvc, ptb reported high chip stability, for flame detection Radiation sensitive area a = 55 mm2 To5 hermetically sealed metal housing with concentrator lens, 1 isolated pin and 1 case pin 10âµw/cm2 peak radiation results a current of approx. 700 na Sg01l-5lens uv photodiod specifications Sensitive area: 55 mm2 Dark current: 3.5 fa Capacitance: 250 pf Responsivity range: 221 - 358 nm Operating temperature: -55 ~ +170â°c Storage temperature: -55 ~ +170â°c Soldering temperature (3s): 260â°c Reverse voltage: 20 v
Spd005gasmd 5 psi gauge pressure sensor with analogue output description This pressure sensor has an amplified analogue output. The sensor is compensated for offset, sensitivity, temperature drift and nonlinearity. The sensor is available in the range from 5 to 100 psi. Other ranges on request. Available in gauge and absolute type. The output is ratiometric to the power supply voltage. 5 v power voltage the output span is 0.5 to 4.5 v. The spd analogue series can be considered as an "analogue" successor of the spd series. Spd005gasmd 5 psi gauge pressure sensor with analogue output electrical characteristics Performance characteristic at vcc =5v excitation 25â°c. Supply voltage: 4.75~5.5v Supply current: max. 3ma Pressure range: 0~5psi Accuracy: â±1.8%fs Operating temâ??perature: -20~85c Storage temperature: -40~125c
O2-M2 Oxygen Sensor Description Alphasense Oxygen sensors use capillary flow control. Unlike partial pressure oxygen sensors, they have good pressure and temperature dependence, making them the best choice in safety applications. Standard galavanic sensors use lead for greatest reliability but fixed lifetime. Specifications * Output: 80 to 120 uA @ 20.9% O2 * Response time t90: < 15 (s) from 20.9% to 0% O2 * Linearity: 0.6 % O2 deviation @ 10% O2 * Operating life: > 24 months *Temperature range: -30 to 55 'C * Pressure range: 80 to 120 kPa * Humidity range: 5 to 95 % rh continuous * Diameter: 20.0 mm (including label) * Heigh: 17.4 mm (including foam ring) * Weight: < 16g
Sonic-anemo-dzp ultrasonic wind speed sensor description: Sonic-anemo-dzp ultrasonic anemometer is powered by its own solar panel. It is well suited to remote installations where power consumption matters. This unit connects directly to a pulse or potentiometer input (i.E. On davis instruments). It is a useful product for professionals, integration to aws (autonomous weather station), and well-informed users. Sonic-anemo-dzp ultrasonic wind speed sensor specification: , output rate: 1 measure and update per second , wind module sensitivity: 0.12 m/s , wind module resolution: 0.05 m/s , wind module dynamic: 0.12 to 40 m/s , direction sensitivity: +/-1.5' , direction resolution: 1' (9 bits) , power supply: photovoltaic panel, battery lifepo4 , op. Temp. Without icing: -15'c to +55'c
Do1200 and do1200tc dissolved oxygen sensors Item no.: do1200/h, do1200/t, do1200tc/h, do1200tc/t, 971598, 971598tc Do1200 dissolved oxygen sensor features * reliable galvanic sensing technology * compact 12mm design * for portable, laboratory or on-line use * optional integral atc element * easy to use pre-membraned replacement caps Do1200 dissolved oxygen sensor description The do1200 and do1200tc feature dependable galvanic technology. No warm up period is required. Sensors are supplied with fast responding hdpe membrane caps for portable or lab use. Optional ptfe membrane caps are available for on-line or heavy uv exposure applications. Fill solution is replaceable when required. The do1200 is supplied without internal temperature compensation. The do1200tc can be supplied with a variety of user defined atc elements. Standard cable length is 2.5 feet with a tinned lead termination. Longer cable lengths and connectors are available for an additional charge. For on-line use, our fc75p 3/4 inch in-line fitting may be ordered to provide for mounting into 3/4 inch fnpt threaded tees. Do1200 dissolved oxygen sensor specifications * range: 0-20 mg/l * body material: epoxy and noryl * max temperature: 50 degrees c * saturation output: hdpe = 47mv +/- 9mv, ptfe = 33mv+/-9mv * pressure: 0-100 psig (7.5 bar) * calibration: single point in air * response time: after equilibration, hdpe 1 minute for 2mv, ptfe 2 minutes for 2mv
Mb7139 xl-trashsonar-wr High performance ultrasonic trash bin measurement Mb7139 xl-trashsonar-wr ultrasonic sensor product description The mb7139 xl-trashsonar-wr1 is a weather resistant sensor designed for trash bin level measurement. The mb7139 xl-trashsonar-wr1 reports the range to the first detectable target in a trash bin. This sensor is our most recommended sensor for testing within trash bins. High output acoustic power combined with continuously variable gain, real-time background automatic calibration, real-time waveform signature analysis, and noise rejection algorithms results in virtually noise free distance readings. This holds true even in the presence of many of the various acoustic or electric noise sources. The xl-trashsonar-wr sensors are factory calibrated to match narrow sensor beam patterns and provide reliable mid-range detection zones. Mb7137 is the i2c version of this sensor. Mb7139 xl-trashsonar-wr ultrasonic sensor product specifiations Resolution of 1 cm 10hz read rate 42khz ultrasonic sensor measures distance to objects Rohs compliant Read from all 3 sensor outpus: analog voltage, pulse width, rs232 serial Operates from 3.0-5.5v Operational temperature from -40'c to +65'c Maximum range of 350 cm (138 inches) Mb7139 xl-trashsonar-wr ultrasonic sensor features and benefits Real-time calibration, noise rejection and additional filtering provides stable range information Excellent for applications that require consistently accurate outputs Impressive acoustic and electrical noise resistance Mb7139 xl-trashsonar-wr ultrasonic sensor applications and uses Autonomous navigation Environments with acoustic and electrical noise Bin level measurement Tank level measurement Trash level measurement
SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Description: As Worldwide Premiere launch, a specific version of the CV7-V which connects directly to the wind sensor input on Davis instruments. This sensor will allow the replacement of mechanical anemometers / wind vanes with no need of anything else but power supply. Itâ??s an exclusive and useful product for both, professionals and well-informed amateurs. SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Specification: * Output rat: 2 Hz / 30 Hz measurement * Wind module sensitivity: 0.12 m/s * Wind module resolution: 0.05 m/s (16 bits) * Wind module dynamic: 0.12 to 40 m/s * Direction sensitivity: +/-1.5' * Direction resolution: 1' (9 bits) * Power supply: 2.7 V to 35 V DC * Electrical consumption: 2.6 mA Avg. @ 12 V * Op. temp. without icing: -15'C to +55'C
Y504-A Dissolved Oxygen Sensor Description The sensor is based on optical fluorescence lifetime quenching technique. Its technical procedure meets ASTM D888-09 standard for optical sensing of dissolved oxygen. This online sensor is developed to integrate with Yosemite wireless monitoring system. Its rugged design and large measurement range make it ideal for sampling, flow cell, ground water and waste water measurements. Y504-A Dissolved Oxygen Sensor Applications Fish farmer, waste water plant, river, stream, and ocean monitoring Y504-A Dissolved Oxygen Sensor Feature * 0-20mg/L or 0-200% Saturation * 0~50 'C; IP68 rating * Membraneless, no electrodes design * No oxygen consumption * Flow Independent * Automatic temperature compensation * No H2S Interference * Low Drift, fast response, and more accurate * Low Maintenance, low operating cost * Easy sensor cap replacement * RS-485; MODBUS protocol compatible Y504-A Dissolved Oxygen Sensor Technical Specifications * Range: 0-20mg/L or 0-200% Saturation * Response Time: 10 sec * Housing IP Rating: IP68 * Accuracy: 1% * Drift: -
