FOP-MA Acoustic Fiber Optic Pressure Sensor The FOP-MA is a fiber optic pressure sensor designed for use in acoustics or microphone applications or whenever a very sensitive pressure sensor is needed. It features high frequency response and a high sensitivity to detect slight pressure variations under the most adverse conditions. The FOP-MA acoustic pressure sensor offers small size, high accuracy, immunity to EMI/RFI, and resistance to corrosive environments. FOP-MA Acoustic Fiber Optic Pressure Sensor Key Features: * Miniature size * All-optic * Immune to EMI/RFI * High resolution * Frequency response up to 30 kHz FOP-MA Acoustic Fiber Optic Pressure Sensor Applications: * Acoustics * Microphone * Automotive * Aerospace * Aerodynamics FOP-MA Acoustic Fiber Optic Pressure Sensor Specifications Pressure range: 0 - 2 psi Resolution(*1): 0.0075 psi Accuracy(*2): ±1% of full scale Frequency response(*3): Up to 30 kHz Connector type: ST connector Operating temperature: -20'C to 150'C (-4'F to 302'F) *1. Signal conditioner dependent. *2. Relative to atmospheric pressure. *3. Maximum achieved with a Veloce 50 signal conditioner.
OPC-R1 PM2.5 Particle Sensor * Reports PM1, PM2.5, PM10 plus histograms * PC software supplied * Removable fan exit adaptor * Small size and low power consumption * Configurable to specific applications OPC-R1 PM2.5 Particle Sensor SPECIFICATION * Particle range: 0.4 to 12.4 Spherical equivalent size (based on RI of 1.5) * Size categorisation: 16 Number of software bins * Sampling interval: 1 to 30 Histogram period (seconds) * Total flow rate: 1.6 L/min (typical) * Max particle count rate: 10,000 particles/second * Measurement mode: 95 mA (typical) * Laser on, fan off: < 5 mA (typical) * Voltage range: 4.8 to 5.2 VDC * Switch-on transient: < 5000 mW for 1ms * Temperature range: -10 to 50 'C * Humidity range: 0 to 95% rh (continuous) (non-condensing) * Weight: < 30 g
Alphasense now provides a solution to some old problems: * Palmes-type diffusion tubes are commonly used for indicative measurement of nitrogen dioxide (NO2) in cities for Local Air Quality Management. But sampling over several weeks gives only one average concentration for the entire sampling period and the result is reported weeks after the measurement. * Odours which were previously ignored by local industry and city councils are now headline problems. There is a growing requirement to monitor odour plumes around landfills, waste water treatment plants, agricultural/ poultry farms and industrial sites- but the cost of the necessary network of monitoring nodes is prohibitive. Hydrogen sulfide (H2S) or ammonia (NH3) are the two mot commonly measured gases for odour detection. Alphasense introduces the Electronic Diffusion Tube (EDT): a single gas data logger with ppb resolution using the proven Alphasense A4 family of electrochemical ppb gas sensors. EDT-01 Electronic Diffusio n Tube Features include: The low cost EDT makes networks affordable User- adjustable logging interval from one minute to four hours Also records relative humidity and ambient temperature * Eight months battery life from two Lithium AA cells * Data is downloaded in seconds via Bluetooth to the Android smart phone app * Designed for waterproof to IP 67 * Mounting bracket connects easily to both walls and poles * Gases include NO2 , NO2 + O3, H2S, NH3 and CO. Sensor data sheets specify performance. Data analysis support available EDT-01 Electronic Diffusion Tube SPECIFICATION * Range: 0-5 ppm (NO2) 0-50 ppm (H2S) 0-500 ppm (CO) 0-100 ppm (NH3) * Temperature range: -20 to +50 'C * Humidity range: 10 to 90%rh continuous * Temp. accuracy: ±0.5'C (-20 to +50'C) * Sampling time: 1 to 256 min EDT-01 Electronic Diffusion Tube Applications include: * Co-locating with Palmes-type diffusion tubes to record diurnal and weekly patterns and peaks * Monitoring urban construction sites for compliance, especially for peak concentrations * Ring-fencing odour sources for plume monitoring- daily downloads provide regular feedback * Tracking ammonia plumes on poultry farms * Detecting fugitive emissions from industrial sites for both leak detection and ensuring compliance * Low cost educational tool when teaching about air quality
MICROceL CF Carbon Monoxide Sensor (CO sensor) Description MICRO 3-electrode carbon monoxide sensor with inboard filter. MICROceL CF Carbon Monoxide Sensor (CO sensor) Key Features & Benefits * A robust carbon monoxide sensor suitable for portable life safety applications * Extremely small size MICROceL CF Carbon Monoxide Sensor (CO sensor) Technical Specifications * Operating Principle: 3-electrode electrochemical * Measurement Range: 0-500 ppm CO * Maximum Overload: 1500 ppm CO * Filter: To remove TLV levels of interfering gases * Sensitivity: 0.045 ± 0.01 µA/ppm * T50 Response Time:
Discription: CJBPZ-I all-in one vibration sensor integrates piezoelectric acceleration sensor with precision measuring circuit that composes high precision vibration measure system. The sensor can connect with DCS, PLC or other equioment directly. It is ideal for measuring vibration of fan, motor, water pump factory equipment etc. Features: Wide measure range All material is Stainless steel Various port type Protection Grade: IP65 Performance Parameters: Frequency Response: 5-1000Hz Natural Frequency of Vibration: 10Hz Measurement Range: Displacement Range: 0-200um, 0- 500um, 0-1000um (opitional) Speed Range: 0-10.0mm/s,0-20.0mm/s, 0-100.0mm/s (optional) Working Voltage: 24V DC Output Currency: 4-20mA Output Impedance: â?¤500 Signal line Specification: wires (DV24V power supply&4-20mA output uses these 2 wires together) 3 wires (earth wire, power supply wire, output wire) Max Acceleration: 10g Measurement Direction: vertical or horizontal Working Ambient: Temperature: -40°C to 85°C, Relative humidity â?¤90% Size: Ï?45Ã?80ï¼?mmï¼? Weight: 450g Thread: M10Ã?1.5 Protection Grade IP65
MB7139 XL-TrashSonar-WR High Performance Ultrasonic Trash Bin Measurement MB7139 XL-TrashSonar-WR Ultrasonic Sensor Product Description The MB7139 XL-TrashSonar-WR1 is a weather resistant sensor designed for trash bin level measurement. The MB7139 XL-TrashSonar-WR1 reports the range to the first detectable target in a trash bin. This sensor is our most recommended sensor for testing within trash bins. High output acoustic power combined with continuously variable gain, real-time background automatic calibration, real-time waveform signature analysis, and noise rejection algorithms results in virtually noise free distance readings. This holds true even in the presence of many of the various acoustic or electric noise sources. The XLTrashSonarWR sensors are factory calibrated to match narrow sensor beam patterns and provide reliable mid-range detection zones. MB7137 is the I2C version of this sensor. MB7139 XL-TrashSonar-WR Ultrasonic Sensor Product Specifiations *Resolution of 1 cm * 10Hz read rate * 42kHz Ultrasonic sensor measures distance to objects * RoHS Compliant * Read from all 3 sensor outpus: Analog Voltage, Pulse Width, RS232 serial * Operates from 3.0-5.5V * Operational Temperature from -40Ë?C to +65Ë?C * Maximum range of 350 cm (138 inches) MB7139 XL-TrashSonar-WR Ultrasonic Sensor Features and Benefits * Real-time calibration, noise rejection and additional filtering provides stable range information * Excellent for applications that require consistently accurate outputs * Impressive acoustic and electrical noise resistance MB7139 XL-TrashSonar-WR Ultrasonic Sensor Applications and Uses * Autonomous Navigation * Environments with acoustic and electrical noise * Bin Level Measurement * Tank Level Measurement * Trash Level measurement
MB7066 XL-MaxSonar-WRL1 High Performance Ultrasonic Precision Rangefinder MB7066 XL-MaxSonar-WRL1 Ultrasonic Rangefinder Product Description The XL-MaxSonar-WRL1 is our longest range (10m) outdoor sensor. The weather resistant XL-MaxSonar-WR is a rugged ultrasonic sensor component module. This outdoor sensor provides very short to long distance detection and ranging in a compact, robust PVC housing. The ultrasonic sensor meets the IP67 water intrusion standard and matches standard electrical 3/4inch PVC pipe fittings. High output acoustic power combined with continuously variable gain, realtime background automatic calibration, realtime waveform signature analysis, and noise rejection algorithms results in virtually noise free distance readings. This holds true even in the presence of many of the various acoustic or electrical noise sources. The XL-MaxSonar-WR sensors are factory calibrated to match narrow sensor beam patterns and provide reliable long range detection zones. MB7066 XL-MaxSonar-WRL1 Ultrasonic Rangefinder Product Specifiations * Resolution of 1 cm * 10Hz read rate * 42kHz Ultrasonic sensor measures distance to objects * RoHS Compliant * Operates from 3.0-5.5V * Low 3.4mA average current requirement * Operational Temperature from -40C to +70C * Maximum range of 1068 cm (450 inches) * Long range, narrow detection zone MB7066 XL-MaxSonar-WRL1 Ultrasonic Rangefinder Features and Benefits * Extended 10 meter range detection and outputs * High acoustic power output * Readings can occur up to every 100ms, 10-Hz rate * Triggered operation provides the range reading as desired * Fast measurement cycle * Quality narrow beam characteristics * Low cost, long range IP67 sensor MB7066 XL-MaxSonar-WRL1 Ultrasonic Rangefinder Applications and Uses * Robot ranging sensor * Autonomous navigation * Distance measuring * Long range object detection * Industrial sensor
MICROceL HS Hydrogen Sulfide Sensor (H2S Sensor) Description MICRO 3-electrode hydrogen sulphide sensor MICROceL HS Hydrogen Sulfide Sensor (H2S Sensor) Key Features & Benefits * A robust hydrogen sulfide sensor suitable for portable life safety applications * Extremely small size MICROceL HS Hydrogen Sulfide Sensor (H2S Sensor) Technical Specifications * Operating Principle: 3-electrode electrochemical * Measurement Range: 0-100 ppm H2S * Sensitivity: 0.105 ± 0.025 µA/ppm * T50 Response Time:
ZE08-CH2O Electrochemical CH2O Detection Module Profile ZE08-CH2O is a general-purpose and miniaturization electrochemical formaldehyde detection module. It utilizes electrochemical principle to detect CH2O in air which makes the module with high selectivity and stability. It is built-in temperature sensor to make temperature compensation. It has the digital output and analog voltage output at the same time. It is a combination of mature electrochemical detection principle and sophisticated circuit design. ZE08-CH2O Electrochemical CH2O Detection Module Features * High sensitivity &resolution, Low power consumption, Long life * UART/Analog Voltage/PWM wave output * Good stability, excellent ability of Anti-interference * Temperature compensation , Excellent Linear output ZE08-CH2O Electrochemical CH2O Detection Module Main Application Portable detector, air-quality monitor, air cleaner, air renewal system, air conditioner, smart home. ZE08-CH2O Electrochemical CH2O Detection Module Technical Parameters * Target Gas: CH2O * Interference Gas: Alcohol, CO &ect. * Working Voltageâ??: 3.7V~9V * Response time: â?¤60s * Detection Range: 0~5ppm * â??Resolution: â?¤0.01ppmâ?? * Operating Temp.: 0~50â?? * Operating Hum.: 15%RH - 90%RH(No condensation) * Working life: 2 years (in air)
IRceL CH4 NDIR CH4 Sensor Description Miniature infrared sensor with on-board EEPROM and thermistor IRceL CH4 NDIR CH4 Sensor Key Features & Benefits: * Integrated thermistor for accurate temperature compensation * EEPROM programmed with sensor specfic performance characteristics * Compact Size IRceL CH4 NDIR CH4 Sensor Technical Specifications * Operating Principle: Non-Dispersive Infra-Red * Measurement Range: 0-5% vol. Methane * Accuracy (-20C to +50C): Within ± (0.1% vol CH 4 + 4% of concentration)?? * Response Time (T90): < 35 Seconds * Supply Voltage: 3-5 VDC, 3.3 V to utilise EEPROM calibration * MTBF: > 5 years
NH3-3E100SE Ammonia Sensor NH3 Sensor Description NH3-3E100SE Ammonia Sensor, 3 Electrode sensor; available in Mini, Classic, 4-Series and 7-Series formats. NH3-3E100SE Ammonia Sensor NH3 Sensor FEATURES * Amperometric 3 electrode sensor cell * Very stable zero reading * Very selective * Highly sensitive * Hydrous electrolyte NH3-3E100SE Ammonia Sensor NH3 Sensor TYPICAL APPLICATIONS * TLV-monitoring, leakage detection * portable & fixed point applications * Food & Refrigeration Industry, General Industry, Semiconductor Industry NH3-3E100SE Ammonia Sensor NH3 Sensor TECHNICAL SPECIFICATIONS * Measuring Range: 0-100 ppm * Sensitivity Range: 130 nA/ppm ± 30 nA/ppm * Resolution at 20°C: < 1 ppm * Linearity: < 10% full scale * Operation Temperature Range: -20°C to +40°C * Operation Humidity Range: 15-90% r.H, non-condensing
SPD005GAsmd 5 psi Gauge Pressure Sensor with Analogue Output Description This pressure sensor has an amplified analogue output. The sensor is compensated for offset, sensitivity, temperature drift and nonlinearity. The sensor is available in the range from 5 to 100 psi. Other ranges on request. Available in Gauge and Absolute type. The output is ratiometric to the power supply voltage. @ 5 V power voltage the output span is 0.5 to 4.5 V. The SPD analogue series can be considered as an analogue successor of the SPD series. SPD005GAsmd 5 psi Gauge Pressure Sensor with Analogue Output Electrical Characteristics Performance Characteristic at Vcc =5V excitation @ 25C. * Supply Voltage: 4.75~5.5V * Supply Current: Max. 3mA *Pressure range: 0~5psi * Accuracy: ±1.8%FS * Operating temperature: -20~85C * Storage temperature: -40~125C
OPC-N3 PM2.5 Particle Sensor * PM1 , PM2.5 and PM10 * Reduced power standby mode * Capability to measure up to 2,000 µ g/m 3 * Onboard temperature and humidity sensor * SPI interface not included, order code 000-0SPI-00 OPC-N3 PM2.5 Particle Sensor SPECIFICATIONS * Particle range: 0.38 to 40 Spherical equivalent size * Size categorisation: 24 Number of software bins * Total flow rate (typical): 1.2 L/min * Sample flow rate (typical): 220 mL/min * Voltage range: 4.8 to 5.2 VDC * Temperature range: -10 to 50°C * Humidity range: 0 to 95 % rh non-condensing *Weight: < 105g
Sonic-anemo-sdi ultrasonic wind speed sensor description Sonic-anemo-sdi is made from the cv7-v to which a sdi12 protocol and optimizing electrical consumption has been added. Sample rate is 2 hz. This ultrasonic wind sensor operates in a request-response mode. This product is more energy-efficient than standard units. The sonic-anemo-sdi is dedicated to meteorological applications. Sonic-anemo-sdi ultrasonic wind speed sensor available data: - average speed and direction over 10 minutes - minimum wind speed and direction for that period - maximum wind speed (gust 3s) and direction for that period - software version and serial number - data measurement quality rate from the sensor - data for sensor diagnostic (manufacturer use only) Sonic-anemo-sdi ultrasonic wind speed sensor specification: * output data format: sdi-12 v1.3 * information transmited: inst. W. Speed, w. Angle, gust ws/wa, avg, min, max, avaibility * output rate: 2 hz / 30 hz measurement * wind module sensitivity: 0.12 m/s * wind module resolution: 0.05 m/s * wind module dynamic: 0.12 to 40 m/s * direction sensitivity: +/-1.5' * direction resolution: 1' * power supply: 2.7 v to 35 v dc * electrical consumption: 2.9 ma avg. @ 12 v * op. Temp. Without icing: -15'c to +55'c * cable: 5 m / 3 x 0.22 mm2 uv proof * connection: 3 wires * weight of unit assembly: 200 gr with mounting parts.
Mb1003 hrlv-maxsonar-ez0 High performance ultrasonic rangefinder Mb1003 hrlv-maxsonar-ez0 ultrasonic rangefinder product description The hrlv-maxsonar-ez0 has the widest and most sensitive beam pattern of any unit from hrlv-maxsonar-ez sensor line. This makes the hrlv-maxsonar-ez0 an excellent choice for use where high sensitivity, wide beam, or people detection is desired. Mb1003 hrlv-maxsonar-ez0 ultrasonic rangefinder product specifiations * resolution of 1-mm * 10hz reading rate * 42khz ultrasonic sensor measures distance to objects * rohs compliant * maximum range of 5000 mm (195 inches) * operates from 2.5v-5.5v * low 3.1ma average current requirement * operational temperature from 0'c to +65'c Mb1003 hrlv-maxsonar-ez0 ultrasonic rangefinder features and benefits * factory calibrated wide beam width * low operating voltages from 2.5v to 5.5v * all range outputs are active simultaneously * high acoustic sensitivity * detects small targets to longer distances * widest beam width for the hrlv-maxsonar-ez sensors Mb1003 hrlv-maxsonar-ez0 ultrasonic rangefinder applications and uses * people detection * small target detection * high sensitivity applications * obstacle avoidance.
Mb7137 i2cxl-trashsonar-wr High performance ultrasonic trash bin measurement Mb7137 i2cxl-trashsonar-wr ultrasonic sensor product description The mb7137 i2cxl-trashsonar-wr is a weather resistant sensor designed for trash bin measurement. The mb7137 i2cxl-trashsonar-wr features the i2c communication interface. This allows for up to 127 sensors to be operated on a single bus for a network of trash bins that are monitored by a single control device for multiâ??sensor operation. High output acoustic power combined with continuously variable gain, real-time background automatic calibration, real-time waveform signature analysis, and noise rejection algorithms results in virtually noise free distance readings. This holds true even in the presence of many of the various acoustic or electric noise sources. The i2cxl-trashsonar-wr sensors are factory calibrated to match narrow sensor beam patterns and provide reliable mid-range detection zones. Mb7139 is the standard version of this sensor. Mb7137 i2cxl-trashsonar-wr ultrasonic sensor product specifiations * resolution of 1 cm * up to 20hz read rate * 42khz ultrasonic sensor measures distance to objects * rohs compliant * operates from 3.0-5.5v * low 3.4ma average current requirement * maximum range of 350 cm (138 inches) * compatible with up to a 400khz i2c bus speed Mb7137 i2cxl-trashsonar-wr ultrasonic sensor features and benefits * real-time calibration, noise rejection and additional filtering provides stable range information * excellent for applications that require consistently accurate outputs * impressive acoustic and electrical noise resistance Mb7137 i2cxl-trashsonar-wr ultrasonic sensor applications and uses * autonomous navigation * environments with acoustic and electrical noise * bin level measurement * tank level measurement
Cv7-e ultrasonic wind speed sensor description The cv7-e is easily integrated into measurement and monitoring systems. Detects gusts with great responsiveness and low latency. The cv7-e is powered by 8-30 vdc power supply and it outputs rs232 / rs422 / 5 v level signal / nmea0183. The cv7-e shows a data rate twice faster than the cv7 and cv7-v with a data output 4 per second. The small size of this sensor makes it very discreet. Like every lcj capteurs products, cv7-e is energy efficient. Cv7-e has proved its value with universities â??laboratories, scientific and wind tunnels successful tests. It can be used connected to a pc and to any system featuring a nmeaâ® input port. Cv7-e ultrasonic wind speed sensor specification: * output data format: nmea0183, mwv, xdr * information transmited: instant. W. Speed, instant. W. Angle, avaibility * output rate: 4 hz / 60 hz measurement * wind module sensitivity: 0.12 m/s * wind module resolution: 0.05 m/s * wind module dynamic: 0.12 to 40 m/s * direction sensitivity: +/-1.5' * direction resolution: 1' * power supply: 8 v to 30 v dc * electrical consumption: 9 ma * op. Temp. Without icing: -15'c to +50'c * cable: 25 cm / 4 x 0.22 mm2, 20 g/m * connection: 4 wires * weight of the head: 100 gr * weight of unit assembly: 200 gr with mounting parts.
Y504-a dissolved oxygen sensor description The sensor is based on optical fluorescence lifetime quenching technique. Its technical procedure meets astm d888-09 standard for optical sensing of dissolved oxygen. This online sensor is developed to integrate with yosemite wireless monitoring system. Its rugged design and large measurement range make it ideal for sampling, flow cell, ground water and waste water measurements. Y504-a dissolved oxygen sensor applications Fish farmer, waste water plant, river, stream, and ocean monitoring Y504-a dissolved oxygen sensor feature , 0-20mg/l or 0-200% saturation , 0~50'c; ip68 rating , membraneless, no electrodes design , no oxygen consumption , flow independent , automatic temperature compensation , no h2s interference , low drift, fast response, and more accurate , low maintenance, low operating cost , easy sensor cap replacement , rs-485; modbus protocol compatible Y504-a dissolved oxygen sensor technical specifications , range, : 0-20mg/l or 0-200% saturation, , response time: 10 sec , housing ip rating: ip68, , accuracy: 1%, , drift:
Fecs40-1000 for the detection of carbon monoxide Figaro's carbon monoxide sensor fecs40-1000 is a unique electrochemical-type carbon monoxide sensor. Its most notable feature is its unique leak-proof structure, making it ideal for co monitors and detectors in various fields. Fecs40-1000 carbon monoxide (co) sensor features: * high sensitivity/selectivity to co * quick response to co * linear output * long life * stable baseline * unique leak-proof structure Fecs40-1000 carbon monoxide (co) sensor applications: * portable and fixed installation co monitors * co detectors * ventilation control for indoor parking garages Fecs40-1000 carbon monoxide (co) sensor specifications: Detection gas: carbon monoxide Detection range: 0 ~ 1000 ppm Maximum overload: 1500 ppm Output signal: 70±15 na/ppm Repeatability: ±2% Resolution: 1 ppm
3SP_O3_5 P O3 Sensor DESCRIPTION SPECâ??s printed sensors offer the performance of the best quality electrochemical sensors at a fraction of the price. SPECâ??s printed sensors are also ultra-thin, offering easy integration into wireless, portable, and networked solutions. These sensors are ideal for health, environmental, industrial and residential monitoring, because of their high performance, low cost and small size. 3SP_O3_5 P O3 Sensor BENEFITS * Small Size with Low Profile (20x20x3 mm) * Long Life (10 years expected life) * Fast Response (< 15 seconds) * Low Power Consumption * Individually Calibrated (NIST Traceable) * ROHS Compliant * Improved stability and ppb performance 3SP_O3_5 P O3 Sensor APPLICATIONS * Air Quality Monitoring * Industrial Safety * Air Purification Control 3SP_O3_5 P O3 Sensor SPECIFICATIONS * Measurement Range: 0 to 5 ppm * Lower Detection Limit: < 20 ppb (instrumentation dependent) * Resolution: < 20 ppb (instrumentation dependent) * Response Time: < 15 seconds typical * Sensitivity nA/ppm @ 5ppm: -60 +/- 10 nA/ppm * Expected Operating Life: > 5 years (10 years @ 23+/-3'C; 40+/-10% RH) * Operating Temperature Range: -30 to 50'C (-20 to 40'C continuous) * Operating Humidity Range - non-condensin: 0 to 100% RH (15 to 95% continuous) * Power Consumption: 10 to 50 uW (circuit & ambient O3 dependent)
