Dry-type transformer has the advantages of large short-circuit resistance, little� maintenance work, high operation efficiency, small dimension and� low noise,� which is commonly used in places with high requirements of� fireproof� and explosion-proof.� This type transformer is widely used in local lighting, high� buildings, airports, docks, CNC machinery and others. � Its cooling methods are divided into natural air cooling (AN) and forced air cooling (AF).� The transformer can operate continuously for a long time under rated capacity� under natural air cooling.� Output capacity of the� transformer can� increase by 50%� under forced air cooling.� It is suitable for intermittent overload operation or emergency overload operation. Due to the load loss and impedance voltage increase significantly when overload, it is not suitable for long time continuous overload operation.
1. The low-voltage winding is of cylindrical or spiral structure, with high mechanical strength and good short-circuit resistance. 2. The corrugated oil tank is adopted to replace� the oil conservator. The oil tank cover and the oil tank are all-welded along the edge or fastened with bolts, thus prolonging the service life of the transformer oil. 3. After oil removal, embroidery removal, and phosphating treatment, the product is sprayed with three times of primer and one time of finish paint inside and outside. The product is salt fog proof, damp heatproof, and fungus� proof, which can meet the special requirements of metallurgy, petrochemical system, and wet and polluted areas. It is beautiful� and reliable. 4. The transformer oil tank is� fully sealed, and� equipped with� pressure reducing valve, signal thermometer, gas relay, etc according to the standard requirements to ensure the safe operation of the transformer. 5. This series of products are beautiful in appearance, small in size, and can reduce the installation area. It is an ideal maintenance-free distribution product.
1. The transformer core is made of imported high-quality cold-rolled silicon steel sheet, which greatly reduces no-load loss and no-load current. The core is� tightly� bound to ensure the compactness and reduce noise. 2. The high and low voltage windings are� made of oxygen-free copper. The low voltage winding of 500KVA and below is of double-layer cylinder structure,� of 630kVA and above adopt double helix or four helix structure. High-voltage winding adopts multi-layer cylinder structure. 3. Dyn11 is used in the transformer connection group to reduce the influence of harmonics on the power grid and improve the quality of power supply. 4. The transformer is a fully sealed structure, with three coats of primer and one coat of finish paint applied on the inner and outer surfaces. The product is salt fog proof, moisture� proof and fungus-proofing, beautiful, durable and reliable 5. The measured noise value is lower than the standard and maintenance free under normal operation.
As the most widely used power facility, power transformers have a wide variety of types and are of great significance to energy conservation and emission reduction. The S13 fully-sealed oil-immersed power transformer is currently the main selection product for power distribution equipment, with significant energy-saving effects. At present, mainstream distribution transformers generally use S13 laminated core power transformers. It adopts a fully oil-filled sealed type, no oil conservator, and a corrugated sheet box structure. The volume of the transformer changes due to changes in temperature and load, which is completely adjusted by the corrugated oil tank. Its no-load loss is much lower than that of S9, and it is resistant to lightning impact It has strong short-circuit resistance, obvious energy-saving effect, and reduces the overall size of the transformer. The S13 transformer is made of high-permeability oriented silicon steel sheet with a thickness of 0.27-0.30mm and a unit iron loss of 1w/kg, while the new S9 type is an ordinary silicon steel sheet with a thickness of 0.30-0.35mm and a unit iron loss of 1.20 -1.55w/kg. The S13 distribution transformers produced by our company all use 30P series high-permeability oriented silicon steel, using foil-wound coils and new insulating materials and processes. The product is resistant to high temperature, impact, and fully sealed structure design to ensure the stability of transformer oil quality It prolongs the maintenance cycle. At the same time, the integral fuel tank composed of corrugated fin radiator is produced by phosphating and multi-layer anti-rust spraying process, which has good weather resistance.
Product introduction This product conforms to the national standard gb1094.1-2013 power transformer and GB / t6451-2015 three phase oil immersed power transformer technical parameters and requirements.� This product has adopted a series of major reforms in material, technology and structure, so that the electrical performance of the product can reach the advanced level of similar products. With the characteristics of high efficiency and low consumption, it can save a lot of power consumption and operation costs, and has remarkable social benefits. It is a new product promoted by the state. It is also one of the more popular products for users.
VOL-1500E auto ct winding machine is used for winding large sized toroidal shape Coils,is a new generation of winding equipment according to the power industry requirement. YW-1500E winding machine features: YW-1500E Large- sized toroidal shape coil CNC circular winding machine Japan Mitsubishi PLC control High productive,human-computer interaction. Stepping motor speed control for accurate winding,Winding speed can be specified using the front panel keys. User friendly control console with touch screen. High-tech shuttle for highest efficiency. Microprocessor based controls, easy for program-setting and handling for operator. Large memory capacity for storing steps of winding. Password protection for administrative settings as well as operators setting. Easy programming of multi-step, multi-speed settings. Heavy machine weight design to avoid machine shaking while winding. Automatically laying wire, change winding direction. Realize dual-wire, multi-wire winding, forward and backward winding, preset 100 different kinds of wire data in machine. Main technical parameters Model VOL-1500E Diameter rang of windable electromagnetic wire �??1.0~3.5mm Min inner diameter of winded coils �??200mm Max outer diameter of winded coils �??1500mm Max height of winded coils 250mm Max winding rotation speed 100rpm Machine tool power 2.2kW Max outline size of machine tool 1300*1000*1500mm Color Blue,Calx,Customizable
MY2 AC100/110 ,DC24V 5A, AC220V 5A, MY2 AC110/120 DC24V 5A, AC220V 5A, MY2 AC12 DC24V 5A, AC220V 5A, MY2 AC200/220 DC24V 5A, AC220V 5A, MY2 AC220/240 DC24V 5A, AC220V 5A, MY2 AC24 DC24V 5A, AC220V 5A, MY2 DC100/110 DC24V 5A, AC220V 5A, MY2 DC12 DC24V 5A, AC220V 5A, MY2 DC24 DC24V 5A, AC220V 5A, MY2 DC48 DC24V 5A, AC220V 5A, MY2-02 AC100/110 DC24V 5A, AC220V 5A, MY2-02 AC110/120, DC24V 5A, AC220V 5A, MY2-02 AC12 DC24V 5A, AC220V 5A, MY2-02 AC200/220 DC24V 5A, AC220V 5A, MY2-02 AC220/240 DC24V 5A, AC220V 5A, MY2-02 AC24, DC24V 5A, AC220V 5A, MY2-02 DC100/110 , DC24V 5A, AC220V 5A, MY2-02 DC12 DC24V 5A, AC220V 5A, MY2-02 DC24 DC24V 5A, AC220V 5A, MY2-02 DC48, DC24V 5A, AC220V 5A
Rectifier transformer
1.Volmet China supplier Automatic pressure epoxy insulator hydraulic APG injection machine 2.Epoxy resin mixing device Application: epoxy resin mixing device is applicable for mixing epoxy resin,hardener,and silica powder,to produce products such as transformer, bushing, post insulator, contact cover, sensor, various supports, etc. 3.Main technical specification Strirring power Strirring Speed Vacuum pump power Worm gear screw jack Vacuum degree 3 �¯�¼?kW�¯�¼? 21-118 �¯�¼?m/min�¯�¼? 1.1KW,2800r/min 0.37 kW 1.5 mbar Dimension of mixer device Weight of mixing device Pot capacity L Machine dimension Machine weight 1900X850X1885 mm 680 KG 100L 910X760X1565mm 455KG APG Clamping Machines factory 1.high quality clamping mould 2.Supply APG moulds 3.Experienced engineers 4.Long life service Products 1:Good product quality, fine surface finish of products without bubbles. 2:High efficiency and high automation,only need 1/2 workers operate APG machine,efficiency greatly raised but the intensity of labor is decreased. 3:Chemical resistance,electrical insulation,strength resistance greatly improved. Advantages: 1.thin film de-gassing, guarantee excellent vacuum degree. 2. oil cycling heating surround pot, heat raw material evenly in winter. 3.Triple safety design 4.electronic vacuum gauge more precision
VOL-1500E auto ct winding machine is used for winding large sized toroidal shape Coils,is a new generation of winding equipment according to the power industry requirement. YW-1500E winding machine features: YW-1500E Large- sized toroidal shape coil CNC circular winding machine Japan Mitsubishi PLC control High productive,human-computer interaction. Stepping motor speed control for accurate winding,Winding speed can be specified using the front panel keys. User friendly control console with touch screen. High-tech shuttle for highest efficiency. Microprocessor based controls, easy for program-setting and handling for operator. Large memory capacity for storing steps of winding. Password protection for administrative settings as well as operators setting. Easy programming of multi-step, multi-speed settings. Heavy machine weight design to avoid machine shaking while winding. Automatically laying wire, change winding direction. Realize dual-wire, multi-wire winding, forward and backward winding, preset 100 different kinds of wire data in machine. Main technical parameters Model VOL-1500E Diameter rang of windable electromagnetic wire �?1.0~3.5mm Min inner diameter of winded coils �?200mm Max outer diameter of winded coils �?1500mm Max height of winded coils 250mm Max winding rotation speed 100rpm Machine tool power 2.2kW Max outline size of machine tool 1300*1000*1500mm Color Blue,Calx,Customizable
three-phase control transformer SBK/SG series-control/isolation Safety, Durability, Stability Mainly used for AC 50/60Hz Commonly used in low voltage switchgear and electric drive control equipment it can work continuously for a long time under the rated load
Brands : Siemens, Schnieder, Abb, L&T, Chint, hager, Havells, HPL C&S etc Poles : SPN, TPN Amperes : 160A 23A 250A Material : acrylic, Metallic Way : 2,4,6,8,10,12,14,16 way Warranty : 12 Months HSN : 8537.10.00
Spec: Voltage Transformer (Brand: M/S Tianshui Changkai) IL: 12/45/75kV 1Kw, 50Hz, 1.9Un:8h
10KVA Industrial Electrical Power Control Transformer Single-phase Control Transformer BK series-Multi-voltage output Safety, Durability, Stability Mainly used for AC 50/60Hz Commonly used in a machine as electrical lighting control and light power supply It can work continuously for a long time under the rated load
5000VA Industrial Electrical Power Control Transformer Single-phase Control Transformer BK series-Multi-voltage output Safety, Durability, Stability Mainly used for AC 50/60Hz Commonly used in a machine as electrical lighting control and light power supply It can work continuously for a long time under the rated load
1000VA Industrial Electrical Power Control Transformer Single-phase Control Transformer BK series-Multi-voltage output Safety, Durability, Stability Mainly used for AC 50/60Hz Commonly used in a machine as electrical lighting control and light power supply It can work continuously for a long time under the rated load
Hebei anmei company produces various transformer accessories. The main products include high-voltage and low-voltage transfomrer bushings (DIN standard, ANSI standard, AS standard, and so on.), oil level gauge, dehydrationg breather, release valve, thermometer, valve, butterfly valve, brass gate valve, bellows, terminals,dry change accessories and so on. company can also be produced according to customer drawings. The products are exported to all world, Asia, the Middle East, South America, Europe, and so on.
DIN Standard Bushing for Transformer12kv 24kv 36kv 250A Electrical Porcelain Insulator DIN(12~36kV/250~630A ) Sequence Number Code Model (Dimensions) Opening arcing distance Creep distance Shield Weight(kg) H h2 h3 Md d1 d3 d4 E C d0 h1 1 AM.DDA.001 DIN-12/250 427 125 60 M121.75 140 74 51 146 70 78 174 300 2 5.3 2 AM.DDD.001 DIN-12/630 475 140 75 M202.5 150 88 60 174 70 92 174 310 2 8 3 AM.DFA.001 DIN-24/250 517 140 60 M11.75 145 74 51 146 100 78 249 440 3 7.2 4 AM.DFD.001 DIN-24/630 565 155 75 M202.5 160 88 60 174 100 92 249 460 3 10.4 5 AM.DGA.001 DIN-36/250 617 140 60 M121.75 155 74 51 146 200 78 349 610 4 8.3 6 AM.DGD.001 DIN-36/630 690 175 75 M202.5 180 88 60 174 200 92 354 670 4 13.5 7 AM.DGA.010 DIN-36/250 617 135 55 M121.75 190 74 51 146 200 78 354 950 6 12.5
DIN Standard Bushing for Transformer12kv 24kv 36kv 250A Electrical Porcelain Insulator
Cast resin transformers Range:160 KVA 11KV up to 10,000 KVA, 33 KV Class In addition to the above, we are capable to supply cast resin dry type transformers for a client's special and stringent requirements to converter, rectifier, static excitation and other special applications as well Standards:
