Send me blueprints or draws with dimensions information to quote Size: E128~196, R.Core, Adaptor, E114~24 Input/Output: Customer's requested specification
Send me blueprints or draws with dimensions information to quote Size: Request customize L: Customer's requested specification Material: Iron, Power Core, Ferrite Core
The transformer core is made of imported high-quality cold-rolled silicon steel sheet, which greatly reduces no-load loss and no-load current. The core is tightly bound to ensure the compactness and reduce noise. *� The high and low voltage windings are� made of oxygen-free copper. The low voltage winding of 500KVA and below is of double-layer cylinder structure, of 630kVA and above adopt double helix or four helix structure. High-voltage winding adopts multi-layer cylinder structure. Dyn11 is used in the transformer connection group to reduce the influence of harmonics on the power grid and improve the quality of power supply. *� The transformer is a fully sealed structure, with three coats of primer and one coat of finish paint applied on the inner and outer surfaces. The product is salt fog proof, moisture proof and fungus-proofing, beautiful, durable and reliable The measured noise value is lower than the standard and maintenance free under normal operation.
Pulse Transformer Pulse transformers can be used for signal transmission, low-power control circuits, camera flashes, radar systems, high-power switched-mode power supplies and other fields where pulsed form of relatively high voltage along with isolation is required.
Being a leader in the industry, we are engaged in offering a qualitative range of 150A Three Phase Air Cooled Variable Auto Transformer to our clients, Beta Power has been manufacturing & Supplying Variacs for the past ten years and has a strong support for OE buyers. Many valued customers have considered it fit to clarify our products as "top of the line". It has full technical competency in handling all the technical requirements of clients. It is well supported by the state of the art winding machinery to give a consistent & accurate job. Needless to mention, a strong backup team with years of experience has put-high reliability in the product. Our Motto is "Customers Satisfaction leads to Good Quality" and our learning curve never ends. We are presently exporting variable transformer in Ethiopia. Features: Very high efficiency Good voltage regulation No wave from distortion Rugged and compact construction Continuous, step less and smooth control of output High short time surge capacity Testing: We are equipped with all Testing Equipment to ensure the quality of Variac Electricals. The company testing section has Testing Panel Board, HV Kit, Megere Test, Oscilloscope, Power Meter, Watts meter etc., which all are calibrated every year as per ISO norms. Models: Air Cooled flush mounting type Air Cooled Servo and Box type No wave from distortion Oil Cooled Complete M.S Tank and without Tank Single Phase, Two Phase, and Three Phase Manually operated {Hand Driven} or Motorised types Standard & Non-Standard Voltage Ranges: Single Phase: Input 240 V, Output 0 to 270 V Two Phase: Input 415 V, Output 0 to 470 V Three Phase: Input 415 V, Output 0 to 470 V Standard Current Ratings: Air cooled types from 2Amps to 60Amps {However we recommend oil cooled types above 30Amps} Oil cooled type from 2Amps to 600Amps Double Layer Dimmers: For Servo controlled Voltage Stabilizers double layer dimmers can be used without separate Buck-Boost Transformers so as to achieve cost efficiency and compactness. These are standardised viz. 1kVA, 2kVA, 3kVA & 5kVA suitable for input range: 170 to 270 V and output: 230 V
Beta Power Controls, Coimbatore, India an ISO 9001:2015 TVE accredited company, leading manufacturing & Exports of Servo Voltage Stabilizer, Isolation Transformers, Frequency Converter, Two phase to three phase converter, Variable Transformer, Rectifiers energy saving equipment in India. Our products are well appreciated world over and received much recognition for their quality. Established in 2007 with a corporate objective to provide efficient energy for greener future, Beta Power Controls has grown to be one of the countryâ??s biggest manufacturers of power saving and power conditioning equipmentâ??s with the largest satisfied customer base. The products manufactured by us have made a distinct place in the market owing to their features like excellent performance, longer lifespan and less power consumption. With an objective to manufacture quality products, our experts use the latest equipment and best quality raw material provided by our trusted vendors of the market. We regularly Exports to isolation transformer in Dubai. Beta Power Isolation Transformers offer complete line isolation, continuous noise filtering to eliminate harmonic distortion and enhanced common mode surge suppression internal low impedance isolation transformer component with Faraday Shield offers 100 % isolation from the input AC line. The Common Mode Noise and Normal Mode Noise are generated in the common Utility Mains due to the Parallel connection of the critical loads to the Noise generating loads. These High magnitudes noises occur between conductors due to switching action of the Load connected in parallel to the sensitive loads, These noise is Isolated by Beta power transformers and safe guard the critical/precise loads like CNC / Medical / Software industry etc. We manufacture 1 kVA to 2000 kVA capacity designed for isolating sensitive equipment from Line Voltage Transients, Spikes & D.C. leakage. Also removes EMI/RFI noise, utility switching transients, and background spikes. Keeping in mind the varied demands of the clients, *The input voltage, output voltage, frequency and phase can be custom made. Our Tamil Nadu Supply Network Coimbatore, Erode, Salem, Karur, Namakkal, Trichy, Thanjavur, Kumbakonam, Mayiladuthurai, Panruti, Cuddalore, Pondicherry, Villupuram, Chennai, Vellore, Ambur, Krishnagiri, Hosur, Madurai, Sivakasi, Rajapalayam, Virudhunagar. Our India Supply Network We are looking for queries Beta Power Equipment from Tamil Nadu, Kochi, Ernakulam, Palakkad, Kerala, Bangalore, Karnataka, Andhra Pradesh, Goa, Maharashtra, Andaman and Nicobar Island. Our Export / Global Network Kenya, Muscat, Egypt, Tanzania, Ethiopia Nigeria, UAE, Kuwait, UK, Qatar, Congo, Saudi Arabia, Malaysia, Philippines, Sri Lanka, South Africa, Yemen, Benin, Angola, Mozambique, Peru, Singapore, Dubai, Lagos, Bahrain, Uganda, Australia, USA, New Zealand.
1.Dry transformers with high and low voltage windings are coated by a thin layer of epoxy resin.It has the advantages of flame retardant, self-extinguishing, moisture-proof, heat dissipation and so on. 2.Equipped with a low-noise air-cooled device, the fan can be automatically controlled to start and close through the thermostat, so that the transformer can be operated with a 40% increase in capacity. 3.It can go deep into load centers, such as high-rise buildings, airports, wharfs, power plants, residential communities or complete sets of substations. 4.The temperature sensing element and the sensing system embedded in the low voltage winding can start and turn off the fan or alarm or trip according to the set value for protection.
100kva electrical power transformer price Ai Power offers three phases, oil immersed, and naturally cooled distribution and power transformers. Our products from 10kva to 20000kva with a maximum voltage 35kv are manufacture under the standard of IEC60076. The windings are made of high-grade electrolytic cooper and are concentrically positioned. Usually copper foil is used for the low voltage windings. Round shaped, enamel insulated wires is used for the high voltage windings.
S11 SERIES POWER TRANSFORMERS The capacity range of 10kV class S11 full seal power transformer is 30kva-2500kva. In 10kV, 50Hz power transmission and distribution system, it can be widely used in high-rise buildings, commercial centers, subways, airports, stations, industrial and mining enterprises, drilling platforms, especially in places with high fire protection requirements such as inflammables and explosives, and in places with poor environment. It can also be used for power and lighting in residential areas, commercial streets and rural areas. Advantages: S11 type fully sealed oil immersed transformer is the main type selection product of current distribution equipment, with remarkable energy saving effect. The S11 distribution transformer produced by our company uses 30p series high conductivity oriented silicon steel produced by well-known enterprises, and adopts new insulating materials and processes. The products are resistant to high temperature and impact. The integral mailbox composed of corrugated radiator is produced by phosphating and multi-layer antirust spraying technology, which has good weather resistance.
On the basis of the S9 series, the S11 series products have an average no-load loss of 20%. The no-load current is 70-85% lower than the S9. The temperature rise is reduced by 10K, and the service life is more than doubled. Even under the load of 20%. it can still be used for a long time. The running noise is reduced by 2-4 decibels. High and low voltage windings, body assembly, fuel tank structure, protection device, etc. are similar to S9 series transformers. It also adopts non-suspension structure, adopts vacuum drying, vacuum oil filtering and oil filling process, adopts corrugated oil tank, and has no oil storage cabinet and other structures.
Transformer can transformer the voltage of a network into the voltage matching the system or load and fulfill power transferring and distributing.Taking the place of transformers with silicon steel core, AMDT can be widely applied in outdoor power distribution networks systems, which is magnificently energy saving and can lessen air pollution. It is especially applicable for areas with insufficient power supply and fluctuating load and where daily maintenance is hard. Since the transformer adopts a fully sealed structure, the insulating oil and the insulating medium are not polluted by the atmosphere, so it can be carried out in a humid environment, making the ideal power distribution equipment in the urban and rural distribution networks.
1. Low energy consumption: The� adoption of isotropic soft magnetic material generates low magnetization power, high electrical resistivity and low eddy current consumption. The no-load loss and current of the core made of amorphous alloy are very low, only 1 / 3 of that of silicon steel sheet. 2. Strong corrosion resistance: the amorphous alloy core� is fully wrapped by resin and high temperature resistant silica glen� which� effectively prevent corrosion and falling off amorphous alloy fragments, and� provide better� protection for the core and coil. 3. Low noise. Improvement of� the structure of iron core and coil and� adoption� of special noise -reduction materials greatly reducing the operation noise. 4. Strong short-circuit resistance. This� product adopts three-phase five-column structure, and the iron core is protected by frame structure. Featured by low temperature-rise and strong heat dissipation, this� product� can work� by� 150% rated load under air cooling condition. Perfect temperature control protection system is applied� to provide reliable guarantee for safe operation of transformer
Dry-type transformer has the advantages of large short-circuit resistance, little� maintenance work, high operation efficiency, small dimension and� low noise,� which is commonly used in places with high requirements of� fireproof� and explosion-proof.� This type transformer is widely used in local lighting, high� buildings, airports, docks, CNC machinery and others. � Its cooling methods are divided into natural air cooling (AN) and forced air cooling (AF).� The transformer can operate continuously for a long time under rated capacity� under natural air cooling.� Output capacity of the� transformer can� increase by 50%� under forced air cooling.� It is suitable for intermittent overload operation or emergency overload operation. Due to the load loss and impedance voltage increase significantly when overload, it is not suitable for long time continuous overload operation.
Dry-type transformer has the advantages of large short-circuit resistance, little� maintenance work, high operation efficiency, small dimension and� low noise,� which is commonly used in places with high requirements of� fireproof� and explosion-proof.� This type transformer is widely used in local lighting, high� buildings, airports, docks, CNC machinery and others. � Its cooling methods are divided into natural air cooling (AN) and forced air cooling (AF).� The transformer can operate continuously for a long time under rated capacity� under natural air cooling.� Output capacity of the� transformer can� increase by 50%� under forced air cooling.� It is suitable for intermittent overload operation or emergency overload operation. Due to the load loss and impedance voltage increase significantly when overload, it is not suitable for long time continuous overload operation.
1. The low-voltage winding is of cylindrical or spiral structure, with high mechanical strength and good short-circuit resistance. 2. The corrugated oil tank is adopted to replace� the oil conservator. The oil tank cover and the oil tank are all-welded along the edge or fastened with bolts, thus prolonging the service life of the transformer oil. 3. After oil removal, embroidery removal, and phosphating treatment, the product is sprayed with three times of primer and one time of finish paint inside and outside. The product is salt fog proof, damp heatproof, and fungus� proof, which can meet the special requirements of metallurgy, petrochemical system, and wet and polluted areas. It is beautiful� and reliable. 4. The transformer oil tank is� fully sealed, and� equipped with� pressure reducing valve, signal thermometer, gas relay, etc according to the standard requirements to ensure the safe operation of the transformer. 5. This series of products are beautiful in appearance, small in size, and can reduce the installation area. It is an ideal maintenance-free distribution product.
1. The transformer core is made of imported high-quality cold-rolled silicon steel sheet, which greatly reduces no-load loss and no-load current. The core is� tightly� bound to ensure the compactness and reduce noise. 2. The high and low voltage windings are� made of oxygen-free copper. The low voltage winding of 500KVA and below is of double-layer cylinder structure,� of 630kVA and above adopt double helix or four helix structure. High-voltage winding adopts multi-layer cylinder structure. 3. Dyn11 is used in the transformer connection group to reduce the influence of harmonics on the power grid and improve the quality of power supply. 4. The transformer is a fully sealed structure, with three coats of primer and one coat of finish paint applied on the inner and outer surfaces. The product is salt fog proof, moisture� proof and fungus-proofing, beautiful, durable and reliable 5. The measured noise value is lower than the standard and maintenance free under normal operation.
As the most widely used power facility, power transformers have a wide variety of types and are of great significance to energy conservation and emission reduction. The S13 fully-sealed oil-immersed power transformer is currently the main selection product for power distribution equipment, with significant energy-saving effects. At present, mainstream distribution transformers generally use S13 laminated core power transformers. It adopts a fully oil-filled sealed type, no oil conservator, and a corrugated sheet box structure. The volume of the transformer changes due to changes in temperature and load, which is completely adjusted by the corrugated oil tank. Its no-load loss is much lower than that of S9, and it is resistant to lightning impact It has strong short-circuit resistance, obvious energy-saving effect, and reduces the overall size of the transformer. The S13 transformer is made of high-permeability oriented silicon steel sheet with a thickness of 0.27-0.30mm and a unit iron loss of 1w/kg, while the new S9 type is an ordinary silicon steel sheet with a thickness of 0.30-0.35mm and a unit iron loss of 1.20 -1.55w/kg. The S13 distribution transformers produced by our company all use 30P series high-permeability oriented silicon steel, using foil-wound coils and new insulating materials and processes. The product is resistant to high temperature, impact, and fully sealed structure design to ensure the stability of transformer oil quality It prolongs the maintenance cycle. At the same time, the integral fuel tank composed of corrugated fin radiator is produced by phosphating and multi-layer anti-rust spraying process, which has good weather resistance.
Product introduction This product conforms to the national standard gb1094.1-2013 power transformer and GB / t6451-2015 three phase oil immersed power transformer technical parameters and requirements.� This product has adopted a series of major reforms in material, technology and structure, so that the electrical performance of the product can reach the advanced level of similar products. With the characteristics of high efficiency and low consumption, it can save a lot of power consumption and operation costs, and has remarkable social benefits. It is a new product promoted by the state. It is also one of the more popular products for users.
VOL-1500E auto ct winding machine is used for winding large sized toroidal shape Coils,is a new generation of winding equipment according to the power industry requirement. YW-1500E winding machine features: YW-1500E Large- sized toroidal shape coil CNC circular winding machine Japan Mitsubishi PLC control High productive,human-computer interaction. Stepping motor speed control for accurate winding,Winding speed can be specified using the front panel keys. User friendly control console with touch screen. High-tech shuttle for highest efficiency. Microprocessor based controls, easy for program-setting and handling for operator. Large memory capacity for storing steps of winding. Password protection for administrative settings as well as operators setting. Easy programming of multi-step, multi-speed settings. Heavy machine weight design to avoid machine shaking while winding. Automatically laying wire, change winding direction. Realize dual-wire, multi-wire winding, forward and backward winding, preset 100 different kinds of wire data in machine. Main technical parameters Model VOL-1500E Diameter rang of windable electromagnetic wire �??1.0~3.5mm Min inner diameter of winded coils �??200mm Max outer diameter of winded coils �??1500mm Max height of winded coils 250mm Max winding rotation speed 100rpm Machine tool power 2.2kW Max outline size of machine tool 1300*1000*1500mm Color Blue,Calx,Customizable
MY2 AC100/110 ,DC24V 5A, AC220V 5A, MY2 AC110/120 DC24V 5A, AC220V 5A, MY2 AC12 DC24V 5A, AC220V 5A, MY2 AC200/220 DC24V 5A, AC220V 5A, MY2 AC220/240 DC24V 5A, AC220V 5A, MY2 AC24 DC24V 5A, AC220V 5A, MY2 DC100/110 DC24V 5A, AC220V 5A, MY2 DC12 DC24V 5A, AC220V 5A, MY2 DC24 DC24V 5A, AC220V 5A, MY2 DC48 DC24V 5A, AC220V 5A, MY2-02 AC100/110 DC24V 5A, AC220V 5A, MY2-02 AC110/120, DC24V 5A, AC220V 5A, MY2-02 AC12 DC24V 5A, AC220V 5A, MY2-02 AC200/220 DC24V 5A, AC220V 5A, MY2-02 AC220/240 DC24V 5A, AC220V 5A, MY2-02 AC24, DC24V 5A, AC220V 5A, MY2-02 DC100/110 , DC24V 5A, AC220V 5A, MY2-02 DC12 DC24V 5A, AC220V 5A, MY2-02 DC24 DC24V 5A, AC220V 5A, MY2-02 DC48, DC24V 5A, AC220V 5A
