1.The brief introductions of gasoline engine water well drilling rig
·This gasoline engine water well drilling rig is an ideal tool for drilling families, wells, air conditioning wells and vegetable garden wells, and is an ideal tool for workers engaged in well drilling and reconnaissance.
·Diversification equipped with power: gasoline engine can be used as power, or single-phase electric and three-phase electric power can be replaced.
·Wide range of adaptation: because the floor area is less than 1 square meters, the height can be controlled around 2.6 meters, so it can be used in the field or indoors.
·It is widely used: it can not only drill holes in the drill pipe, but also use the center tube to sample. It can also use positive and negative circulation water to do well.
2 .The features of the gasoline engine water well drilling rig
The gasoline engine water well drilling rig consists of gasoline engine, reducer, belt, seat, movable pulley, wire rope, pipe pliers, pulling device, bit broken soil, sealing water gourd, drop box, landing card, pump, water pipe and so on.
The volume of the gasoline engine water well drilling rig is 1*0.7 *0.4m, and the portal frame bar is 2.6 meters high. The total weight is about 150 kilograms. The head of the main engine (including gasoline engine, reducer, water hyacinth and frame) weighs about 50 kilograms, the chassis is 35 kg, the portal frame rod is 17 kg, the drill rod is 3 kg / m, and the other is about 30 kg.
Diameter 28 drill pipe, recommended opening diameter of 120 millimeters, 80 meters deep, the deepest record 100 meters (different soil and water pump, the effect is different). The 34 drill pipe recommends the maximum opening diameter 160 millimeter, the depth is 30 meters. It can be drilled into 10-20 meters in one hour, and 2-3 cents per meter.
1.The applications of FY260 crawler pneumatic water well drilling rig
·civil engineering drilling
·geothermal drilling,
·drilling with large diameter
·deep drilling footage
·fast, flexible and efficient.
2.The specifications of FY260 crawler pneumatic water well drilling rig
Model FY260
Gross weight t 6.2
External dimension mm 3900*1950*2550
Aperture mm 140-325
Drilling depth m 260
Feed stroke mm 3000
Travel speed km/h 2.5
Grade ability max. 30°
Rising height from ground mm 250
Wind pressure mpa 1.7-3.0
Air consumption m³/min 17-35
Engine power kw 85
Rotary speed rpm 40-70
Rotation torque n.m 7000-9000
1. Brief introductions of KQZ-70D pneumatic-electric DTH drilling rig
KQZ-70D pneumatic-electric DTH drilling rig is a new type of high efficient drilling rock equipment designed for water conservancy projects and construction sites. It is widely used for drilling in all kinds of rock strata in open pit, water conservancy and construction slope treatment.
KQZ-70D pneumatic-electric DTH drilling rig is a percussive rotary drilling rig. Its internal structure is different from that of a general jack drill. Its valve train and reciprocating piston mechanism are independent, that is impactor. The front is directly connected to the bit, and the back is connected to the drill pipe. when drilling the rock, the impactor dive the hole. The piston (hammer body) in the impactor is made reciprocating to strike the drill tail through the valve, making the drill produce a kind of gyration force to the rock bottom.
2. Features of KQZ-70D pneumatic-electric DTH drilling rig
Small in size, light in weight, suitable small space that large and medium-sized drilling rig can not work , convenient and flexible.
3.Specifications of KQZ-70D pneumatic-electric DTH drilling rig
KQZ-70D
Borehole diameter mm 50-80
Drilling depth m 10-15
Rotating speed r/min 112
Air consumption m³/min 3.5-4.5
Cylinder diameter mm 90
Drilling pipe mm 42
Motor power kw 3
Main engine length mm 1524
Main engine weight kg 148
1.Brief introductions of KQZ-100D pneumatic-electric DTH drilling rig
KQZ-100D pneumatic-electric DTH drilling rig is a new type of high efficient rock drilling equipment, designed for water conservancy projects and building materials sites. It is widely used for drilling in all kinds of rock stratum and drill hole. For example, water conservancy and construction slope treatment.
KQZ-100D pneumatic-electric DTH drilling rig is an impact rotary drilling rig. Its internal structure is different from the general drilling machine. Its gas distribution and piston reciprocating mechanism are independent with each other. The front end is directly connected to the bit, and the back end is connected to the drill pipe. When it is divided into the hole, the impactor will rotate in hole. the piston (hammer body) in the impactor is made reciprocating to strike the drill tail through the valve, making the drill produce a kind of gyration force to the rock bottom.
2.Features of KQZ-100D pneumatic-electric DTH drilling rig
Small volume, light weight, suitable for large and medium-sized drilling rig can not workplace, convenient and flexible.
3.Specifications of KQZ-1 00D pneumatic-electric DTH drilling rig
KQZ-100D
Borehole diameter mm 65-150
Borehole depth m 20-25
Rotating speed of drilling tools r/min 90
Air consumption m³/min 6-8
Cylinder diameter mm 150
Drilling pipe mm 50/ 60
Motor power kw 4
Main engine length mm 2400
Main engine weight kg 224
1.Brief introductions of KHYD110 electric rock drilling rig
·The electric rock drilling rig can be fitted with drill stand, and can be drilled horizontally or upward in any direction.
·In order to prolong the service life of the drill bit and improve the working conditions of the operator, wet drilled water can be used to discharge the powder and screw blade drills can also be used for dry draining.
·In the operation of electric motor rock drilling rig, we only need to operate the handwheel, and the electric motor rock drilling rig can advance itself and return quickly.
2.Specifications of KHYD110 electric rock drilling rig
Model Unit KHYD110
Rated output power of motor kw 5.5
Rated voltage of motor v 380/660
Rated frequency of motor hz 50
Rated current of motor a 11.6
Motor speed r/min 1440
Motor phase number three phase communication
Rated working mode continuity
Drilling speed mm/min 280
Speed of return m/min
Borehole diameter mm 42-80ï¼?rockï¼?
Hardness range protodikonov`s scale of hardness f
5745 Drilling Machines Tools Suppliers
Short on time? Let Drilling Machines Tools sellers contact you.
1.Brief introductions of ZDY-1250 full hydraulic tunnel drilling rig
ZDY-1250 hydraulic tunnel drilling rig is used for coal mine: Z stands for drilling rig; D stands for tunnel; Y stands for hydraulic driven, and 1250 is the maximum output torque of 1250n. m.
2.Applications of ZDY-1250 full hydraulic tunnel drilling rig
ZDY1250 tunnel drilling rig is mainly used for drilling holes of gas pumping (row), grouting hole, water injection hole, anti process and pressure relief hole, geological exploration hole and other engineering drilling holes. Drilling rig can drill holes in the range of azimuth and dip angle specified in the basic parameter table.
3.Specifications of ZDY-1250 full hydraulic tunnel drilling rig
Project Unit ZDY-1250
Maximum drilling depth m 200
Open hole diameter mm Ф87/Ф115
End hole diameter mm Ф65/Ф75
Drilling pipe diameter mm 50
Drilling angle ° -90-+90
Rated output rotating speed r/min 80/170
Rated output torque n.m 1250/600
Rated power kw 22
Rated voltage v 380/660
Rated current a 42.5/24.5
Feeding force kn 60
Pullout force kn 45
Anchorage force kn 4*45
Rated advance speed m/min 0-1.5
Feed stroke mm 850
Hardness range (protodyakonov scale of hardness) fâ?¤10
Noise db(a) â?¤92
Main engine dimension (long*width*high) mm 2240*1000*1478
Total weight (without drill rod) kg 1820
1. Characteristics of XY-44A hydraulic core drilling rig
XY-44A is a hydraulic core drilling rig suitable for high-speed medium and deep borehole drilling in complex rock formation. HuaxiaMaster core drilling rigs covers all the main foundation and drilling technologies with a range of models whose characteristics, capability and performance find application in every operating condition.
2. Applications of XY-44A hydraulic core drilling rig
·Core drilling rig
·Engineering geology exploration,
·hydrology and core drilling
·large diameter foundation piles construction
3. Parameters of XY-44A hydraulic core drilling
rig
XY-44A hydraulic core drilling rig
Drilling depth 600-1400m
Max open hole caliber 300mm
End hole caliber 75mm
Drilling rod diameter 60mm
Drilling angle 90-65
Drill rig moving stroke 450mm
Spindle
1. Characteristics of XY-8 hydraulic core drilling rig
·Machine adopts pneumatic shift Fastgear 8JS118 auto transmission and clutch, compact structure, smooth operation, stable performance, good wild card.
·Using auto-control flexible-shaft shift agency, we achieve the long-distance transmission shift. The pneumatic shift is light and agile, and has the advantage of hommization.
·Reasonable speed range and many speed radixes (8 forward speed, 1 reverse speed), with low-speed it has big torque (Max. up to 8000N.m).
·Using concentrated forced lubrication system, as long as the rig runs, the separate lubrication oil pump starts working and sends lubrication oil to each node that requires lubrication. When the oil lubricates drive mechanism, it will also take away the heat inside, (lubrication system with separate condenser), to prevent the components from heat caused by high-speed high-load state.
·hydraulic oil is supplied by gear oil pump, less power consumption, and the hydraulic system oil temperature is low and stable work. The system is equipped with a hand pump. When power machine can not work, workers can still use hand pump to lift tools from the bottom of the hole, in order to avoid burying accidents
·Advanced and compact structure, reasonable layout, all components are revealed outside, do not overlap, ease of maintenance, maintenance and repair.
·The rig has a low center of gravity and long backward stroke (up to 530mm). Easy to be fixed on tower base, the rig has good stability in high-speed drilling.
·With shockproof meter, its easy to observe hole situation. Control-handles are in reasonable layout, operation is flexible and reliable.
2. Parameters of XY-8 hydraulic core drilling rig
Drilling angel 0-360°
Electric motor Y280S-4 /75KW
Diesel engine YC6A240-33/ 177KW
Spindle 96mm
Shanxi Fast Gear 8JS118 transmission and ancillary clutch, safe and reliable.
Oil pump type/ model gear oil pump/ CB-32
core speed 2500r/min
Displacement 32 ml/r
Work pressure 20mpa
Max.pressure 25mpa
Direction of rotation Right(see from shaft end)
Work core speed 700-1800r/min
Single rope compensational speed 3-8m/s
Single rope compensational load 45kn
Form skids type(with sliding base)
Rig backward stroke 530mm
Dimensions(L*W*H) 3800*1500*2460mm
Rig weight 6500kg
1.Brief introduction of QTZ-3 soil sampling drilling rig
QTZ-3 soil sampling drilling rig is more humanized and more suitable for researchers in scientific research institutions or universities. The power is further strengthened, which can meet the requirement of soil sampling for 15-20 meters depth.
2.Applications of QTZ-3 soil sampling drilling rig
·Geotechnical engineering investigation; environmental soil survey; agricultural soil survey.
·Ground water survey; coastal geological survey; wetland environment investigation.
·Tailing pond investigation, archaeological investigation, physical chemistry and secondary halo sampling.
3. Technical parameters of QTZ-3 soil sampling drilling rig
QTZ-3 soil sampling drilling rig
Power power 3.8hp
lighter way back flush pull rope
oil consumption 0.6 l/h
Impact times 2460 r/min
Impact energy 35j-70j
Core depth 15m-20m
Host weight 26kg
1.Brief introductions of SH30-2A exploration drilling rig
SH30-2A exploration drilling rig is modified and designed on the basis of SH30 exploration drilling rig. The exploration drilling rig can be used for the covering layer of fourth Century, such as soil, clay, sand and gravel, and all kinds of mixed soil and fill. It is mainly used in the exploration of gold sand, industrial buildings and civil buildings as well as highway, railway, bridge and other engineering geological prospecting work.
2.Features of SH30-2A exploration drilling rig
SH30-2A exploration drilling rig is simple operate and has high degrees of mechanization. With light weight, compact structure, good disintegration performance and convenient handling, the SH30-2A exploration drilling rig can be removable in the mountain area and is equipped with a pair of rubber wheels. The machined can be towed between different drilling holes on constructions site. .
3.Applications of SH30-2A exploration drilling rig
The SH30-2A exploration drilling rig has two kinds of drilling methods: impact and rotation. Therefore, the drilling tools of the drilling machine are divided into two kinds: impact tools and rotary tools. In order to meet the customer's individualized demand, the drilling tools are equipped in accordance with the demand , and the standard configuration does not include the rotary drilling function.
4.Impact tool of SH30-2A exploration drilling rig
The tools used for impact drilling include lifting joints, weighting rods, impact rods, guiding pipes and impact drills. When the soil sample is used, the drilling tool used is the same as above, but only the impact bit is changed into a soil sampler.
Using sand cylinder for sand gravel and other tools are lifting joint, rod, movable joint, sand lifting cylinder. When drilling in sand and pebble layer, casing must be lowered to protect the hole wall and prevent collapse. With complete free chain clamp c
5.Rotary tool (Not include in standard configuration).
Rotary Table, Auger Drilling Pipe, Rotary Table Pipe Adapter,
6.Specifications of SH30-2A exploration drilling rig
SH30-2A exploration drilling rig
Drilling depth 30m
Drilling pipe diameter 42mm
Aperture diameter 142mm
End hole diameter 110mm
Drill form and vertical height 4 legs, 6m
Power
Motor Y132S2-2/ 7.5kw/3000 r/min
Diesel engine D180Z/ 8hp/2400 r/min
Windlass
Lifting speed 0.24/ 0.57/1.48m/s
Maximum lifting power (single rope, low speed) 15kn
Turntable
Diameter 150mm
Turntable speed 18/44/110r/min
Dimension
Length*width*height 1780*1010*900mm
Weight 500kg
1.Features of KY-150 hydraulic exploration drilling rig for metal mine
KY-150 hydraulic exploration drilling rig for metal mine is easy to disassemble and convenient to transport. The drilling rig has flexible arrangement, and the drilling pipe can be dismantled mechanically, which can reduce labor cost and improve work efficiency. Also the rig has infiniTely variable speeds.
KY-150 hydraulic exploration drilling rig for metal mine has the function of linkage. It is simple and safe to control the rig through the operation platform. The spindle of the gyration adopts the through hole structure. The length of the drill pipe is not restricted by the drilling rig, and it can also be applied to diamond wire-line coring drilling.
KY-150 hydraulic exploration drilling rig for metal mine uses full hydraulic operation to make the structure more reasonable to make the function more complete. It uses variable motor which has wide speed regulating range. This drilling rig applies to high speed drilling of alloy steel stone and hard alloy drilling at low speed, and it is suitable for any inclination drilling in the tunnel or surface drilling.
2.Components of KY-150 hydraulic exploration drilling rig for metal mine
The KY-150 hydraulic exploration drilling rig for metal mine adopts the structure of full hydraulic power head, and consists of three parts: main engine, pump station and operating floor.
3.Specifications of KY-150 hydraulic exploration drilling rig for metal mine
Borehole diameter 36.5mm/46.5mm
Drilling depth 150ï¼?Ï?33 steel drill pipeï¼?/120ï¼?Ï?43 steel drill pipeï¼?/150(Ï?43 aluminum alloy drill pipe)
Borehole angle 0°-360°
Spindle speed 400-1400 r/min
Spindle output torque 87-300 n.m
Rated pull force 30 kn
Rated pull speed > 0.3 m/s
Oil supply mode double gear pump
Hydraulic oil mode antiwear hydraulic oil YB-N46/YB-N32 (winter)
Motor model manual variable motor A6V55MA
Motor specifications Y180M-4/18.5 kw
Equipment weight main engine166kg/backbone 40kg/operation floor 86kg/power car 210kg
1.Introduction of JDL-300 mud/air drilling rig
JDL-300 mud/air drilling rig is a water well drilling rig that mix mud drilling rig and air drilling rig in one equipment with mechanical top head. It is a good solution to the difficulty of drilling in the soil layer for DTH rig and the low efficiency of drilling for mud rotary rig in the hard rock, gravel and pebble layer. The mud/air drilling rig adapts to various soil strata. The mud/air drilling rig is efficiency and energy saving to drill water well and geological exploration of core sample.
2.Features of JDL-300 mud/air drilling rig
·The rig can be equipped with a five-speed manual integrated gearbox, hydraulically separated bearings, full synchronizer shifting, high reliability and long service life.
·The drilling rig adopts a mechanical winch, which has a fast lifting speed and is easy to handle the bottom hole accident.
3.Parameters of JDL-300 mud/air drilling rig
JDL-300 mud/air drilling rig
Working stratum Loose soil layer and bed rock(hardness:F6~20)
Drilling
method Mechanical top head rotation, hydraulic feeding,
work with mud pump or DTH.
Drilling
capacity Φ42 Mud drilling depth 530m
NQ wireline coring 600m
Φ75 Air Drilling depth 300m
Borehole dia. �Φ350
Power Diesel engine model YN27
Rated power 42kw
Rated speed 2400rpm
Drive
head Rotary speed 50~10200r/min
Max. torque 5000N.m
Feeding
system Lifting capacity 4T
Thrusting capacity 2.1T
Winch
capacity Hydraulic tool winch(optional) 1.5T
Mechanical winch 4.5T
Drill
pipe Drill pipe dia. Φ76/Φ89/Φ102
Drill pipe length 3000mm
Crawler
chassis Walking speed 0~2km/h
Climbing angle 20°
Dimension Transport 5380*1575*2500mm
Working 3480*1575*6280mm
4380kg
Air
compressor Air pressure 10.5~24.6bar
Air consumption 16~35m³/min
The above parameters are subject to change without prior notice.
Shandong Master Machinery Group specializes in mud/air drilling rig. The main models are JDL-300 and JDL-400.
1.The applications of KQZ-180D pneumatic water well drilling rig
KQZ-180D pneumatic water well drilling rig is suitable for drilling and geothermal drilling. It has the advantages of large diameter, deep drilling, fast track, flexible movement and wide use.
2.The specifications of KQZ-180D pneumatic water well drilling rig
Drilling hole diameter 100-219mm
Drilling depth 150m
Drilling angle ground to 45-90°
Feed stroke 1500mm
Motor power 7.5kw
Rotary speed 0-78rpm
Wind pressure 0.8-2.1mpa
Air consumption 13-21L/min
Gross weight 600kg
1.The applications of FY300 crawler pneumatic water well drilling rig
·civil engineering drilling
·geothermal drilling,
·drilling with large diameter and deep drilling footage
·Its fast, flexible and efficient
2.The specifications of FY300 crawler pneumatic water well drilling rig
Model FY300
Gross weight t 8.8
Dimension mm 4350*1850*2750
Aperture mm 140-325
Drilling depth m 300
Feed stroke mm 6000
Travel speed km/h 2
Grade ability max. 30°
Rising height from ground mm 230
Wind pressure mpa 1.7-3.3
Air consumption m³/min 23
Engine power kw 85
Rotary speed rpm 55-115
Rotation torque n.m 7200-8500
1.The features of SPJ-300 water well drilling rig
·SPJ-300 water well drilling rig is powered by electric motors.
·The drilling rig is a bulk rotary table drill, which is mainly used for middle Quaternary, fine grained strata and soft rock layers. The main usage is: the hydraulic geological conditions at the bottom of the exploration and survey; the agricultural irrigation, the industrial water use, the underground tunnel ventilation, the bridge and other engineering drilling.
·When drilling rig works, mud flushing fluid (positive circulation) and rotary table are used to drive the drilling tools to rotate.Use winch system to realize decompression drilling, lifting drilling, down pipe , impact sampling, vertical drilling tower,etc..
·The drilling rig is equipped with fine adjustment drilling mechanism and mechanical screwing down drilling tool device
2.The specifications of SPJ-300 water well drilling rig
Borehole diameter 500mm-1500mm
Drilling depth 300m
Maximum output torque 18kn.m
Active drilling pipe 108*108*12mm
Drilling pipe 89mm
Main windlass lifting power 30kn
Assistantwindlass lifting power 20kn
Rotary table latus rectum 500mm
Rotating speed (forward and inversion) 40/70/128r/min
Height of the drilling tower 13m
Gross weight (excluding drill rod) 9t
External dimension 2200*6000*13000mm
Drilling tower Type A / hydraulic drill tower
This product is widely used inwater conservancy project , pile foundation engineering, bridge construction and so on
1. Brief introductions of QTZ-1 soil sampling drilling rig
QTZ-1 soil sampling drilling rig is comparable to a huge hydraulic and pneumatic drilling rig. The drilling rig is a dynamic gasoline driller used for soil sampling, The rig uses gasoline power and is simple in operation. The rig is safe and stable in performance. It can greatly reduce the labor force, taking into account the rapid and simple sampling speed.
2.Applications of QTZ-1 soil sampling drilling rig
·Geotechnical engineering investigation,environmental soil survey,agricultural soil survey.
·Groundwater survey,coastal geological survey,wetland environment investigation.
·Tailing pond investigation, archaeological investigation, physical chemistry and secondary halo sampling.
3. Technical parameters of QTZ-1 soil sampling drilling rig
QTZ-1 soil sampling drilling rig
Power power 2.8hp
fire mode backflush pull rope
oil consumption 0.5l/h
Impact times 1500r /min
Impact energy 20J-55J
Core depth 5m-10m
Host weight 23kg
1.Brief introductions of KY-200 hydraulic exploration drilling rig for metal mine
KY-200 hydraulic exploration drilling rig for metal mine is widely used for tunnel and surface geological exploration and can drill the hole from any angle. The KY-200 hydraulic exploration drilling rig for metal mine adopts the structure of all hydraulic power head and consists of three parts: main engine, pump station and operation floor. The hydraulic exploration drilling rig for metal mine is easy to disassemble and is convenient to transport. The drilling rig arrangement is flexible. Drilling pipe screwing and unscrewing is mechanized. It can save labour cost and improve work efficiency. And it has infinitely variable speeds.
KY-200 hydraulic exploration drilling rig for metal mine has the function of linkage. It is simple and safe through controlling the operation floor. The spindle of the gyration adopts the through hole structure. The length of the drill rod is not restricted by the drilling machine, and it can also be applied to the diamond wire-line coring drilling.
2.Specifications of KY-200 hydraulic exploration drilling rig for metal mine
Drilling pipe diameter (mm) 33 43 Output torque (n.m) 81-295
Borehole depth (m) 200 160 Feed capability(kn) 27
Feeding stroke (mm) 850 Pullout capability (kn) 20
Spindle speed (r/min) 600-2000 Motor power (kw) 22
1.Brief introductions of SJD-2A portable electric water well drilling rig
electric water well drilling rig are widely used in household/factory water wells, irrigation Wells, installation of water air conditioning, construction piling and so on.
The electric water well drilling rig bit produced by the company can be optionally equipped with drill bit, the price of drill bit is calculated separately.It can also be equipped with a drill pipe, with a diameter of 32mm and the length about 1.8m.
2.Features of SJD-2A portable electric water well drilling rig
The whole machine is about 8KG, and it is easy to carry.Power 220V electric ,household two-phase electrical lighting, motor power 1200W or 1500W.The motor can be multi-stage variable speed, positive and negative, and easy to operate.The well drilling depth can reach 50 meters, the wellhead diameter is 50-180mm, the general drill bit 50-180mm, the special specification can be customized.The diameter of the drill pipe is 32mm or 42mm and a length is 1m to 2m.
1.The features of SPJ-400 water well drilling rig
·SPJ-400 water well drilling rig is powered by diesel engine, and can also be driven by motor in electric power area.
·The drilling rig is a bulk rotary table drill, which is mainly used for middle Quaternary, fine grained strata and soft rock layers. The main usageis: the hydrogeological conditions at the bottom of the exploration and survey; the drilling and drilling for the agricultural irrigation, the industrial water use, the underground tunnel ventilation, the bridge and other engineering drilling.
·When drilling rig works, mud flushing fluid (positive circulation) and rotary table are used to drive the drilling tools to rotate. Use winch system to realized ecompression drilling, lifting drilling,down pipe, impact sampling, vertical drilling tower.
2.The specifications of SPJ-400 water well drilling rig
Borehole diameter 500mm-1800mm
Drilling depth 400m
Maximum output torque 18kn.m
Active drill rod 108*108*12mm
Drilling pipe 89mm
Main indlasslifting power 30kn
Assistant windlasslifting power 20kn
Rotary table latus rectum 500mm
Rotating speed (forward and inversion) 40/70/128r/min
height of the drilling tower 13m
Gross weight (excluding drill pipe) 9t
External dimension 2200*6000*13000mm
Drilling tower type A / hydraulic drilling tower
This product is widely used inwater conservancy project , pile foundation engineering, bridge construction and so on.
5745 Drilling Machines Tools Suppliers
Short on time? Let Drilling Machines Tools sellers contact you.
