Snap-in type, can be mounted directly on PC board. Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy. Available with anti-ESD ground terminal. Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Detector Switches is applied to low current circuit (Secondary circuit) push switch used for electronic equipment. Appearance of the Switch shall have good finishing and shall have no rust, crack of plating failures. Terminal Strength of a static load of 3N(306 gf) shall be applied to the tip of terminal in a desired direction for 1 minute. The number of test shall be once per terminal.
Tact Lever Switches is applied to low current circuit push switch for electronic equipment. Appearance of the Switch shall have good finishing, and no rust, crack or plating failures. Operating force of a static load shall be applied to the tip of actuator in operating direction. Robustness of terminal of a static load of 2N(200gf) shall be applied to the tip of terminal in a desired direction for 1min. the test shall be done once per terminal.
Micro Switch action is PUSH-ON TYPE S.P.D.T Contact resistance measurements shall be made with a 1KHz ± 200Hz max DC 5V 1A contact resistance meter. Insulation resistance measurements shall be made following application of DC 500 V potential across terminals and across terminals and frame for one minute. The travel distance for the plunger to come to a stop shall be measured
Hook Switch is applied to low current circuit hook switch for electronic equipment. The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar. Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature. 45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure. Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
Tact Switch MT 1101 SE is applied to low current circuit tactile switch for electronic equipment. Storage temperature range 96 hours maximum for continuous storage over a range The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
Tact Switch MT 1101 V Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100V potential across terminals and frame for one minute.
Tact Switches MT 1101 Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1 kHz small-current contact resistance meter. Insulation resistance measurements shall be made following application of DC 100 V Potential across terminals and frame for one minute
Tact Switches MT 1102HT Contact resistance applying a static load twice the actuating force to the center of the stem, measurements shall be made with a 1kHz small-current contact resistance meter. Insulation resistance Measurements shall be made following application of DC 100V Potential across terminals and frame for one minute
Tact Switches MT 1102 VS is applied to low current circuit tactile switch for electronic equipment .Contact resistance measured DC 5 V 1 A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Tact Switches MT 1101 U is applied to low current circuit tactile switch for electronic equipment. Contact resistance measured DC 5V 1A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Working Principle: when the host tilts or falls, the ball inside the anti-dump switch is tilted and displaced along with the housing under the action of gravity. The tablet is restored to its original position due to the detachment of the ball, and the switch is instantly disconnected, thereby reach the purpose of cutting off the power or circuit. Rating voltage: DC5V Output signal: High or low voltage Size: Φ15.5 Title angle: 30±5° Reset angle: 70±5° Response angle: 360° Life time: 50,000h Installation: Horizontal Material: PC Application: electric heaters; oil heaters; electrical fans; electrical irons; air conditions; air purifiers; physiotherapy equipment; sports equipment; other electrical appliances and equipment that need anti-fall protection.
The products so displayed are modular plates and switches and sockets used for home and office use.
electrical life at full load: 500,000 cycles Operating temperature: -30 to 85 Panel thickness: 1.5mm min.-4mm max Total travel: 1.5mm Operating force: 3N-6N Contact Bounce: 10ms Mechanical life: 1,000,000cycles Degree of protection: IP68
Product name: Intelligent frameless bathroom anti-fog LED makeup plug in the mirror panel with touch switch Size : 60*70cm~140*70cm this product is Bluetooth and no Bluetooth Material: Hd environmental protection silver mirror Function: Switch Quickly change the click switch and touch it again quickly, it will quickly change to the light you want. The memory function turns off the indicator light and turns it on again or the color of the previous memory, eliminating the inconvenient operation. LED lights and fog lamps can be controlled separately, more energy efficient! Press and hold both switches to adjust the time! Mirror The explosion-proof mirror protects the nest, does not splash the water, protects the safety of the family Intelligent frameless bathroom anti-fog LED makeup plug in the mirror panel with touch switch
Detailed Product Description WavelengthRang: 1525~1565 Insertion Loss: 1.0(Typ.); 1.3(Max.) Return Loss: 30 Crosstalk: 30 Switching Speed: Regular (200~400); Ultra-fast (10~30) Repeatability: +/- 0.01 Features 1 No moving parts 2 Switching speed is fast 3 extremely stable latch mode 4 Low power consumption 5 Excellent stability and reliability Application High speed protection System monitoring test measurement Fiber sensing system Product Description The 1x2 or 2x1 optical switch is a solid-state optical switch that does not have any moving components inside and is based on the Faraday effect. The series uses the principle of electromagnetic induction and the Faraday rotation effect to change the polarization state of the incident beam. In combination with the birefringent polarization beam splitting crystal, the beam propagation path is changed, thereby realizing the function of optical path switching.
Solar DC switch for inverter at 32A: 1.32A,1500VDC; 2.suitable for solar inverter; 3.with 2P&4P&6P. info@new-pv.com http://www.new-pv.com/products_show.asp?id=232
Technical specification: Rated voltage AC110-220V (50/60Hz)/DC24V Operating Temperature -20 °C ~ +50 °C Operating power 800W Installation Method Ceiling mounted Detecting angle 360 degree Contacting way input 220VAC, output 220VAC Lux range 5 Lux ~ 500Lux ± 20% ajustable Delay range 16~1000 Secs ± 30% Detector destance 8 M
Technical specification: 1. Operating voltage: DC12V 2. Ambient temperature: -20 C +50 C 3. Own power:
