Model Number:
Portable Air Conditioner ((WT-F26 gray)
Power Type: DC
Use: Room
Condition: New
After-sales Service Provided: None
Warranty:1 year
Type: PORTABLE
Certification:CB, ce
Cooling/Heating:Cooling Only
Application:Car, Commercial, Garage, Hotel, Household, Outdoor, RV
Power Source:Electric, usb
Remote Control: Yes
App-Controlled: Yes
* K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors.
It is also used for jointing chemical resisting stoneware pipes.
K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles.
The concrete surface needed protection should be dryed, clean and rough.
The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner.
When Bedding and Jointing Materials are the same.
On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints.
The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water.
Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic.
When Bedding and Jointing Materials are Different.
Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR
A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions.
PREPARATIONS OF MORTAR :
* Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan.
* Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar.
* In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared.
* The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites.
Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature.
Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts.
PREPARATION OF FURANE MORTAR :
Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life.
Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
The Ground Granulated Blast Furnace Slag (GGBS/GGBFS) is a type of eco-friendly green building material and high quality secondary cementitious material for concrete and cement. It is recognized as one of the best secondary cementations material for building high durable concrete stricture in the world today! GGBS has taken over a top place of high-performance cement and concrete mineral additives with its unique characteristics of hydration, low-price raw material. GGBS is obtained by quenching molten iron blast furnace slag (a by-product of iron and steel making) in water or steam. It is then further grounded into the desired fineness in terms of the required particle size distribution. The main components of blast furnace slag are CaO (30-50%), SiO2 (28-38%), Al2O3 (8-24%), and MgO (1-18%). The other important aspect of GGBS is its superiority in concrete durability which extends the lifespan of buildings from fifty years to a hundred years.
APPLICATIONS
Soil stabilization
Mortar
Used in combination with Portland cement
Pre-cast concrete
Ready mix concrete
Specialist projects
369161 Construction Household Furnishing Suppliers
Short on time? Let Construction Household Furnishing sellers contact you.
Aggregates are mixtures of sand, gravel, crushed rock or other bulk minerals used in construction, principally as a component of concrete, and in civil engineering. At CEMENTATION we supply aggregates for a range of core applications, from fill materials to aggregates that can be used in concrete, precast concrete, asphalt and for surface dressing. Aggregate plays an important role in concrete and construction part. We supply quality material which makes durable concrete with higher compressive strength and low permeability having better finish. We can supply a wide range of coarse, fine and blended aggregates in accordance with international standards.
We acquire rock mines and stone crushing plants and enable us to fulfil contract of any size. Progressive stages if crushing and screening enable us to produce a range of aggregate sizes (06mm to 65mm)
APPLICATIONS
Road and Highway surfaces
Constructions or Civil work
Railway Ballast
To make Concrete or Asphalt
Filling
Feldspar is the name given to a group of minerals distinguished by the presence of alumina and silica (SiO2) in their chemistry. This group includes aluminum silicates of soda, potassium, or lime. It is the single most abundant mineral group on Earth. They account for an estimated 60% of exposed rocks, as well as soils, clays, and other unconsolidated sediments, and are principal components in rock classification schemes. The minerals included in this group are the orthoclase, microcline and plagioclase feldspars.
APPLICATIONS
Glass making
Ceramics
Porcelain
Electrodes
Abrasion
We at CEMENTATION produce Feldspar of minerals containing Potassium and Sodium. Our supply is available in Lumps, Granules and Powder form.
Quartz is the most abundant and most common mineral on the Earth. It is found in almost every geological environment and also it is at least a component of almost every rock type. It has a hexagonal crystal structure and is made of trigonal crystallized silica. It is most varied in terms of varieties, colours and forms.
The most important distinction between the types of quartz is that one is of macro crystalline, which is individual crystal visible to the unaided eye, and the other is microcrystalline or cryptocrystalline varieties, aggregates of crystals visible only under high magnification. Chalcedony is the generic term for cryptocrystalline quartz. The transparent variety tends to be microcrystalline and the cryptocrystalline varieties are either translucent or mostly opaque.
Bauxite is a naturally occurring mineral comprising mainly of aluminium hydroxides (the trihydrate Gibbsite Al(OH)3and the AlOOH monohydrate polymorphs boehmite and diaspore), with other components in the mineral typically being silica, iron oxide, titania and aluminosilicates (clay etc). It’s a rock from Laterite soil and it is a primary Ore of Aluminium.
Properties of Bauxite include low iron content; a high Polished Stone Value (PSV) for high friction surfacing applications; a high melting point and density.
APPLICATIONS
Gunning materials
High friction surfacing
Minerals for abrasion
Refractory castables
Mouldable and Ramming Mixes
Refractory mineral blends
CEMENTATION believes in supplying quality bauxite with consistency to its customers across the world, according to their needs.
Rockwool, also known as mineral wool, is an insulation material made from natural stone or mineral fibers. The density of Rockwool refers to the mass of the material per unit volume, and it is commonly expressed in kilograms per cubic meter (kg/m�³) or pounds per cubic foot (lb/ft�³).
The density of Rockwool can vary depending on the specific product and its intended application. Common densities for Rockwool insulation products range from approximately 40 kg/m�³ (2.5 lb/ft�³) to 200 kg/m�³ (12.5 lb/ft�³) or more. The choice of density often depends on factors such as thermal performance requirements, structural support needs, and the specific application of the insulation.
Essential details
Place of Origin:
AUSTRIA
Brand Name:
contact to supplier
Model Number:
contact to supplier
Packaging & delivery
Lead time:
Quantity(metric tons) 1 - 20 >20
Lead time (days) 5 To be negotiated
Gold Fin condenser: Corrosion-resistant, ideal for coastal environments
Variable-speed DC inverter compressor: Reduces operating costs
R-410A refrigerant: Environmentally friendly
Standard 7-year compressor/5-year parts warranty with optional registration for a limited lifetime compressor warranty
The MRCOOL 4th Generation DIY 36K BTU, 18 SEER Ductless Heat Pump is one of the most powerful single-zone systems in the DIY Series, designed to heat and cool areas up to 1,500 sq. ft. This complete system includes a 36K condenser, 36K air handler, and a 25 ft. pre-charged line set filled with R-410A refrigerant. With its impressive 18 SEER efficiency rating, it delivers exceptional performance while remaining energy-efficient.
What makes this system even more appealing is its easy DIY installation. Thanks to the patented MRCOOL Pre-Charged Quick-Connect Line Set, homeowners can install the system using just a few hand tools, making refrigerant piping connections as simple as turning a few wrenches.
Beyond performance and ease of installation, this system boasts multiple operational features. Users can choose from six operating modes: AUTO, HEAT, COOL, FAN-ONLY, DRY (dehumidification), and SLEEP, ensuring customized comfort for every situation. The "Follow Me" function continuously adjusts the room temperature based on the reading from the handheld remotes location, maximizing comfort.
Additionally, the system can be controlled remotely via the Smart HVAC app, compatible with both Apple and Android smartphones. MRCOOL backs this product with a limited lifetime compressor warranty, offering long-term peace of mind.
Heat Pump Complete System
Energy Star
4th Gen
DIY-12-HP-WM-115C25
Key Features:
Up to 22 SEER efficiency
Gold Fin condenser: Corrosion-resistant, ideal for coastal environments
Variable-speed DC inverter compressor: Lowers operating costs
R-410A refrigerant: Environmentally friendly
Standard 7-year compressor/5-year parts warranty with optional registration for a limited lifetime compressor warranty
Introducing the latest advancement in home comfort technology: the 4th Generation MRCOOL DIY 12K BTU, 22 SEER Ductless Heat Pump System.
This powerful single-zone unit is designed to efficiently heat and cool areas up to 500 sq. ft.
It comes complete with a 12K condenser, 12K air handler, and a 25 ft. pre-charged line set filled with R-410A refrigerant.
Installation is made easy with quick connectors, requiring no special tools, equipment, or professional training.
What sets the MRCOOL DIY system apart from its competitors is its exceptional 22 SEER efficiency rating, earning it Energy Star certification for energy savings and performance.
With multiple operating modes HEAT, COOL, DRY (dehumidification), and SLEEP users can customize their comfort to suit their preferences.
The system also features the "Follow Me" function, which automatically adjusts the room temperature based on the readings from the handheld remote.
For added convenience, the system can be fully controlled via smartphone using the Smart HVAC app, giving users remote access to all modes and functions.
MRCOOL is the only brand to offer a limited lifetime compressor warranty, showcasing their confidence in the system's durability.
!!!!!!!!!!!PLEASE SEND YOUR INQUIRY FOR OUR BEST WHOLESALE PRICES!!!!!!!!!!
Super Multi NX (R32) 4MXM80RVMA (8.0kW) Reverse Cycle Multi Split Air Conditioner
The Super Multi NX (R32) 8.0kW Multi Split Air Conditioner offers a versatile and energy-efficient cooling and heating solution suitable for various indoor environments. This system is designed for new installations, ensuring optimal performance and comfort.
Key Features:
Model: Super Multi NX (R32) 8.0kW 4MXM80RVMA (Outdoor Unit)
Indoor Unit: Wall Mounted 3.5kW CTXM35RVMA
Electrical Safety: Includes electrical connection with a certificate of electrical safety.
Concealed Ducting: Metal ducting to hide electrical and refrigerant connections for a cleaner installation.
Pipe Work Coverage: All pipe work is covered by color bond capping for durability and aesthetics.
Secure Installation: Features a poly/concrete slab to secure the outdoor unit against shifting or movement.
Isolator Switch: Installation of a weatherproof isolator switch for added safety and convenience.
Condensation Drain: Includes installation of a condensation drain pipe to prevent water accumulation.
Rubbish Removal: Complete rubbish removal from the installation site.
Warranty: 5-year manufacturer warranty and 6-year workmanship guarantee by ComfyHome Heating & Cooling.
FFQ09W2VJU9 | Indoor Units (x2)
FFQ12W2VJU9 | Indoor Units
FFQ18W2VJU9 | Indoor Units
Selected Remote Controller (x3)
BYFQ60C2W1W | Ceiling Cassette Grille- White (x3)
4MXL36WVJU9 | Outdoor Unit
Manufacturer Warranty:
12-Year Parts Limited Warranty
Daikin's Multi-Zone Systems allow homeowners to control the cooling and heating temperatures independently across up to four separate zones, addressing common temperature disputes and making unused rooms more comfortable.
This system includes various indoor unit styles, such as wall-mounted, concealed slim-duct, ceiling cassette, and floor-mounted options, tailored for both residential and commercial needs.
Multi-head split air conditioners consist of a single outdoor unit connected to multiple indoor units, allowing for efficient and independent cooling in various rooms without ductwork.
We supply wide range of brands. Please inquire for best prices
Key Features:
Multiple Indoor Units: Connects up to five indoor units to one outdoor unit, making it ideal for homes or offices with several rooms.
Independent Temperature Control: Each indoor unit can be controlled individually, enabling tailored comfort settings for different spaces.
Compact Installation: Requires less installation space than traditional systems, offering a streamlined solution for limited outdoor areas
369161 Construction Household Furnishing Suppliers
Short on time? Let Construction Household Furnishing sellers contact you.
