Engines: perkins engines impoted, and with perkins engine manufacturers to form partnerships for many years, ensure that the mechines capable of performing various work environments. Form: manufacture, pleasing in apperance, durability, hydraulic tank, fuel tank and chassis integration, in the structure to fully maximize the performance of the machine, arm and body to work the perfect combination.Operation system: the operating system can choose the advanced mechanical manipulation of clear structure and easy maintenance. Pilot control lever controls the various types of instrument parameters, can greatly improve operator comfort. Leveling system: adopts imported machinery or hydraulic leveling system;leveling system, not only to improve to become more effective, but also increased the use of safety coefficient. Cab: rops/fops, big space, cab design features a full range of vision. Body seat safety bar can accommodate larger opetators, and can serve as handrails, comfort and support to achieve precise control operation.Cab enclosure with a roof, rear window, side windows.Cab air-conditioning system can be powerful in the most hot, cool and comfortable work environment. Maintenance: just open the cover after the tail, on the cover, set off a cab, will be able to complete all inspections including engines, and filling work, and to maintain the filter and battery.In the maintenance of safeway and maintenance without having to raise start-arm, which can effective use of maintenance time, rather than wasted on maintenance and maintenance of open and close to the point. 3150*1945*1610mm
Engines: perkins engines impoted, and with perkins engine manufacturers to form partnerships for many years, ensure that the mechines capable of performing various work environments. Form: manufacture, pleasing in apperance, durability, hydraulic tank, fuel tank and chassis integration, in the structure to fully maximize the performance of the machine, arm and body to work the perfect combination.Operation system: the operating system can choose the advanced mechanical manipulation of clear structure and easy maintenance. Pilot control lever controls the various types of instrument parameters, can greatly improve operator comfort. Leveling system: adopts imported machinery or hydraulic leveling system;leveling system, not only to improve to become more effective, but also increased the use of safety coefficient.Scalable chassis and dozer blade could be retracted when the excavator pass through narrow space and when they reachout could raise whole machine's stability. Deflectable working device makes it work flexible even in a small and narrow space. Full closed pros/fops cab is optional, imported luxury seats, safe and comfortable. Turnover armrest makes driver get on or get off conveniently. Standard heater Standard hydraulic power output pipes. Optional gps satellite positioning system and remote monitoring system. 2760*1060*2550mm
Specific details Teng chang tech trade electrodes for sumitomo type-37 fusion splicer
Specific details Teng chang tech trade electrodes for sumitomo type-39 fusion splicer
Specific Details Teng Chang Tech Trade Electrodes for Fujikura FSM-20PM, 30P, 30S, 30SF, 30PF, 40F, 40S, 40PM, 20CSII Fusion Splicer
Main parameter: 1.Load capacity:2000kg/1500kg/1000kg per cage 2.Independence height:15m 3.Lifting speed:33m/min 4.Max lifting height:150m 5.Person capacity:24 per cage 6.Cage dimensions:3*1.3*2.4m 7.Section dimensions:65.*65.*1508mm 8.Safety breaker type:SAJ3.0*1.2/SAJ4.0*1.2 9.Motor power:11*3/15*2kw Construction hoist seaworthy construction container
1. Super-strong steel structure made of extensive imported original parts, ensuring more stability and reliability for the concrete block machine body. 2. The whole process uses a plc aptitude control and dialogue system of human-machine interface, easy to analyze the chance signal, ensure the best operation effect. 3. High-efficient and super-strong vibration system, computer-control flow pressure of the hydraulic system, realize vertically synchronous vibration, frequency conversion, and braking, with synthetic output compounded with double vibration sources, thus greatly increase product compactness and mold-box service life. 4. The cloth system adopts semi-closed screen reticular rotational feeding unit to feed materials forcedly, with evenness and even speed, ensuring product intensity. 5. Fitted with special hydraulic loading unit, readily realize mass and automatic production, saving a great deal of human power, maintenance field, and circulating fund investment. 8800mmx2480mmx2980mm, weight is 11t
1.Power source: pneumatic operated internal line up clamps 2.Applicable pipe size: 6 to 80in 3.Inputting pressure: inputting pressure 4.Working pressure: between 0.5mpa and 0.8mpa 5.Driving: self-propelled 6.High matching accuracy: unfitness of butt joint is below 1mm Plywood seaworthy packing
Name of commodity: wheel barrow Model: wb3800 Material: metal Weight: 12.7kg Load: 100kg Water capacity: 60l Sand capacity: 4cbf Wheel amount: 1 Wheel size: 13*3 L/h/c: 1380*540*450 A/b/h: 830*615*245 In bulk
ModelLw-6Lw-7Lw-8Lw-10 Price to shanghai(rmb)13675145901552016450 Matched power hp16-3525-7545-8570-120 Digging depth(mm)1850215026403000 Digging height(mm)2500340035104000 Unloading height(mm)1733187819522540 Digging radius(mm)2800336039303886 Weight (kg)620650680760 Bucket turning angle(degree)160160160150 Swing angle for boom(degree)140140140160 Valve pressure(mpa)16161616 Bucket width(mm)250300400500 Bucket cbm0.030.0360.0480.06 Iron crate
.C.F" (korea) heavy duty concrete vibrator shafts, head dia 32mm, 38mm, 45mm length 6 meter long, packed in carton box. Supply with petrol engine or electric motor. Packed in carton box Carton box
Please read completely through these insturction before using the crimper. your DOUGLAS DE 1600 HAND CRIMPER is supplied factory pre-set for quic change-over between most aluminium window systems. PLEASE NOTE : The crimping bench should be constructed in such a way as to offer suitable support for the material being crimped, in order to protect material being crimped from damage, it is advisable to cover the bench bearers with carpet to similar and keep the surfaces clear of swarf or objective likely to damage material surfaces. SETTING UP Remove crimper from box, locate on corner of suitable bench, which must be a robust and stable comstruction. Secure to bench with four M10 counters unk bolts or screws. Insert handles into handle sockets and secure with loking screws which must locate into dimples provided on handle ends. Remove toggl clamp from packing and fix to top of anvil block with two M6 x 10 socket cap screws which are located in the anvil block. WARNING : (1) Do not operate the crimper unless both handles are secured as described above, failure to comply may result in the handles slipping out of the sockets and causing a hazard to the operator. (2) The punch heads are sharp and must be handled with care. The DE 1600 hand crimper is designed for two handed operation by one operator only. It is the operators responsibility to ensure that the path of the punch heads are unobstructed are operating the hand lever handles. TOOLING CHANGES ANVIL INSERT (1) Loosen locking screws (R) Fig. 1 and lift of insert (Q) (2) Slide alternative insert into place, ensure face marked "TOP" is uppermost, locate firmly on bottom face or pins, ensuring that the rear face of the anvil insert sits flat against the anvil block. CRIMP PUNCH HEADS (1) Remove completely the retaining screws (J) Fig 1 (2) Pull Punch Heads our of location slots. (3) Clean all location faces. (4) Select correct punch heads to match anvil insert, push into location slots, replace retaining screws (J) and screw down. TOGGLE CLAMP ADJUSTMENT (1) Select short mitred corner from off-cuts of profile to be crimped, insert correct cleat (s) and corner brance (s) and locate corner on anvil insert. (2) Adjust clamp spindle (v) Fig 1. so that when clamp lever locks ito forward locked position the test corner is held by the clamp pd, with a pressure equivalent to a firm finger pressure. (3) Tighten clamp spindle lock nuts. PLEASE NOTE ! If the clamp pressure is set to high, distortion of profile will occur resulting in poor crimping. CRIMPING TEST JOINT Before starting production it is advisable to test toooling changes as follows :- (1) Leave small sample corner piece in position after setting Clamp. (2) Bring the handles in towards the centre until Cr5imp Heads touch the profile. (3) Open box section profiles the crimp action can be performed by applying equal pressure to both handles simultaneously until the Link Ars (F) Fig 1. lock into a straight line with Punch Heads. (4) When crimping heavy gauge or closed box section profiles it may be found easier to hold one Crimp Punch Head firmly against profile for support whilst the other Head is crimped into it's full depth. Then with a slight alteration in stance, the first head can be pushed to it's full depth. (5) Both crimp Punch heads should be withdrawn from the profile simultaneously. PLEASE NOTE ! Under no circumstances should any one Punch Head be used without firm support of the other one. failure to observe this basic rule will result in the profile frame moving on the anvil insert, a poor crimped joint being produced and possible damage to the Crimper. SETTING CHECK The crimper is supplied factory set and has been test crimped prior to dispatch if for any reason the setting of the crimpter is in doubt the following procedure should be adopted. (1) Cut a sample corner of material to be crimped (2) Carefully check the cut and establish that the cut is a true 45, flat and at 90 to both legs of the section. (3) Offer the appropriate setting piece to the anvil insert and check that the setting is as shown Fig. 2 (4) The punch heads tips should engage onto the slope of the cleat as shown and should either just "skim" the setting piece or clear with minimal clearance. (5) The punch heads should ride down the slope until the link arms lock into straight line with the punch heads. The initial setting for the depth to which the punch heads should run is approximaterly two thirds of the full tepth see Fig. 2 The optimum setting is best established by carrying out test crimps and checking results. PLEASE NOTE A Setting Piecd can be made up by fixing with a suitable adhesive, two packing strips to the back of a cleat that is to be used in the system. The packing strips must be eqial in thickness to the wall of the profile to be crimped. ADJUSTMENTS Should the crimpel require resetting, both the anvil position and the depth of bite of the crimp heads are fully adjustable ANVIL ADJUSTMENT 1) Remove the clamp assembly (U) by removing 2 screws (T), this will reveal a socket head screw. Slacken this screw. 2) Slacken the four nuts at the extreme rear of the crimper (S). 3) Using the setting piece as a guide, adjust the anvil towards or away from the crimp punch heads by turning the nuts. Set the anvil so that the crimp punch heads ride down the slope of the setting piece as shown in Fig 2. ADJUSTMENT OF PUNCH HEADS Each ram assembly is secured tgo the casting by 2 screws (P), slaken to allow the punch head assembly to slide in the casting. By slackenning the lock nut and adjusting screws (N), the position of the punch heads can be adjusted. Adjustments should be initially set so that the crimp punch heads run down the slope on the setting piece to approximately two thrids depth. The assembles must be locked in this position by re-rightening the socket screws (P). The final depth setting is best established by carrying out test crimps and making minor adjustments until satisfactory results are obtained. NOTE Setting the bite of the punch heads too deeply is to be discouraged, if set too tight the resulting joits will not necessarily be tight. "bottoming out"on the cleat is not necessary when trying to obtain a good quality crimp. An indication that the cimper is set over tight, is difficulty encountered when withdrawing crimp punch heads from the crimped material Ensure that all the bolts and nuts are tightened after adjustment have been carried out to maintained settings. is it important that when the crimper is finally set, the heads should both run equal depths on the test piece. It is important that the anvil is set so that the crimp punch heads ride down each slope in the same manner, i.e. the anvil must not be set askew relative to the crimp punch heads. MAINTENANCE Standard packing by using wooden box for which we have government policies and standards for safe delivery of the products. we are also arranging the third party inspection for quality of products and packaging which is useful for clearance of goods specifically for Africa.
20, 000 fly ash bricks in 8 hour shift. Power saving - 15% Operating pressure - 150 bar Cycle time - 20 seconds Production - 15 bricks in one stroke.
Production capacity:160tph Mixer capacity:2000kg.
Max. Theor. Concrete output: 80m3/h Concrete pumping pressure: 16mpa Distribution valve: s pipe valve Hopper capacity: 700l Hopper height: 1400mm The max. Delivery distance (vertical / horizontal): 200/1000m Diesel engine model: weichai deutz Engine power: 130kw Hydraulic oil tank capacity: 580l Fuel tank capacity: 250l Dimension: 6000*2160*2600mm Weight: 6480kg Container
SAP64 asphalt batch mix plant Performance features 1 special burners, adapted to use all kinds of fuel: light and heavy fuel oil, natural gas, coal 2 drying drum with reliable output, rock wool insulation layers design, energy-saving consideration 3 four-grade screening, 4+1 hot storage bins 4 dust filter ensure the environmental emissions 5 dust collection system included Specifications of sap64 Plant output: 64 tph Batch mixer: 800 kg Advantage 1 modular design, fast assembly, lower erection cost 2 easy operation and maintenance 3 reliable output capacity 4 compact appearance. Wooden cases
Sap120 asphalt batch mix plant An ideal plant for maintenance work or medium road project, because it combines wide range of configurations. Sap120 asphalt mixing plant is really the best choice for its excellent production / price/quality. Finished storage bins optional Water filter or bag house filter Performance features 1.Special burners , adapted to use all kinds of fuel: light and heavy fuel oil, natural gas, coal 2.Drying drum adopted friction driving system, rock wool insulated layer 3.Pre-assembly sections, reduced erection cost and time 4.Bag house filter , with 450 lowest dust emissions, meet all environmental restrictions Mixing tower include 4 sections 1.Screen sections , eccentric shaft vibration design, with 21.4 sq.M 2.Hot bins sections , 4+1 silos , emergency overflow included 3.Weighing for aggregate, filler, bitumen and mixer sections 4.Optional hot mix storage bins , under mixer Advantages 1.Economical energy consumption 2.Reliable output capacity 3.Modular type mixing tower 4.Flexible configuration option Specifications of sap120 Output120 tph Batch mixer1500 kg Dryer drumDia:1800 mm ;length: 8000 mm Mixing towerHeight:15500mm Discharge height: 3500mm. Wooden cases
SAP40 asphalt batch mix plant Sap40 asphalt batch mix plant is an economical and practical choice for mid and small invest customers. Advantage: Economical solutions for batch mix process Reliable Simple Easy operation and maintenance Features: 4 size cold feed Reclassification with vibration screen for hot aggregate Special burners , adapted to use all kinds of fuel: light and heavy fuel oil, natural gas , coal Rock wool insulation layers for drying drum Temperature sensors be positioned in the outlet of drying drum , keep the aggregate reach the appropriate degree Specifications of sap40 Plant output 40 tph Batch mixer 500 kg Dryer drum Dia:1200 mm ;length: 5200 mm. Wooden cases
Sap100 asphalt batch mix plant An medium-capacity plant are intend for construction project. Finished storage bins optional An ideal plant for maintenance work or medium road project Mixing tower Screen sections , eccentric shaft vibration design, with 21.4 sq.M Hot bins sections , 4+1 silos , emergency overflow included Weighing for aggregate, filler, bitumen and mixer sections Optional hot mix storage bins, under mixer Performance features Special burners, adapted to use all kinds of fuel: light and heavy fuel oil, natural gas, coal Dryer drum with motor+ gearbox driving system 4 + 1 hot storage bins, emergency overflow included Mixing tower with modularity design Advantage Modularity design for fast assembly Energy saving Excellent control of all metering process Reliable production in any environment and working conditions Specifications of sap100 Output 100 tph Batch mixer 1250 kg. Wooden cases
Working power-----three phare ac 380v 50-60hz Welding mains-----dc 290-330v Rated power-------8kva Max power ------12kva Welding electricity-----1000-2000a(secondary side). Total weight is about 1600kg
